Download or read book Metallic Powders for Additive Manufacturing written by Enrique J. Lavernia and published by John Wiley & Sons. This book was released on 2024-03-06 with total page 613 pages. Available in PDF, EPUB and Kindle. Book excerpt: Metallic Powders for Additive Manufacturing Overview of successful pathways for producing metal powders for additive manufacturing of high-performance metallic parts and components with tailored properties Metallic Powders for Additive Manufacturing introduces the readers to the science and technology of atomized metal powders beyond empirical knowledge and the fundamental relationships among the chemistry, microstructure, and morphology of atomized metallic powders and their behavior during additive manufacturing. The text sets a foundation of the underlying science that controls the formation and microstructure of atomized metallic droplets, including the relations among the properties of metallic powders, their performance during the manufacturing processes, and the resulting products. Other topics covered include the influence of powder on defect formation, residual stress, mechanical behavior, and physical properties. The concluding two chapters encompass considerations of broader societal implications and overarching themes, including the exploration of alternative feedstock materials, economic analysis, and sustainability assessment. These chapters offer valuable perspectives on the prospective trajectory of the field. Written by a team of experienced and highly qualified professors and academics, Metallic Powders for Additive Manufacturing includes information on: Atomization techniques such as Vacuum Induction Gas Atomization (VIGA), Electrode Induction Melting Gas Atomization (EIMGA), and Plasma Rotating Electrode Process (PREP) Atomization science and technology, covering control of atomization parameters, powder size distribution, effect of processing variables, and theoretical models of atomization Heat transfer and solidification of droplets, covering nucleation, microstructure development, and important thermal and solidification conditions during atomization Atomization of Al, Fe, Ni, Co, Ti, and high entropy alloys, as well as composite powders for additive manufacturing, and guidelines for atomization equipment and powder handling Fundamental processing principles in a variety of metal additive manufacturing processes Powder characteristics and requirements for different additive manufacturing processes Effect of powder chemistry and physical characteristics on additive manufacturing processes, and the microstructure and properties of the built parts Evaluation of alternative feedstock sources for metal additive manufacturing, beyond gas atomized powder Economic and sustainability perspectives on powder production and additive manufacturing Metallic Powders for Additive Manufacturing is an excellent combination of rigorous fundamentals and a practice-oriented and forward-looking resource on the subject for materials scientists and practicing engineers seeking to understand, optimize, and further develop the field of powder production and additive manufacturing.
Download or read book Metal Powder Based Additive Manufacturing written by Kun Zhou and published by John Wiley & Sons. This book was released on 2023-05-17 with total page 325 pages. Available in PDF, EPUB and Kindle. Book excerpt: Metal Powder—Based Additive Manufacturing Highly comprehensive resource covering all key aspects of the current developments of metal powder—based additive manufacturing Metal Powder—Based Additive Manufacturing provides valuable knowledge and critical insights regarding the recent advances in various metal powder—based additive manufacturing techniques. This book also reviews typical powder preparation processes and highlights the significance of metal powder—based additive manufacturing for various industrial applications. The key features covered in this book: A rigorous overview of the underlying theories and practical applications of metal powder—based additive manufacturing techniques, including laser powder bed fusion, electron beam melting, laser-based directed energy deposition, and metal binder jetting. An expansive introduction of each technique and its significance pertaining to the printing processes, metallurgical defects, powder materials, equipment, and the microstructures and mechanical properties of the printed parts. A deep exploration of the preparation processes of metal powders for additive manufacturing and the effects of different processes on the powder properties. Comprehensive case studies of parts printed by metal powder—based additive manufacturing for various industrial applications. By providing extensive coverage of relevant concepts in the field of metal powder—based additive manufacturing, this book highlights its essential role in Industry 4.0 and serves as a valuable resource for scientists, engineers, and students in materials science, powder metallurgy, physics, and chemistry. The rich research experience of the authors in additive manufacturing ensures that the readers are provided with both an in-depth understanding and informative technical guidance of metal powder—based additive manufacturing.
Download or read book Additive Manufacturing of Metals written by Leila Ladani and published by . This book was released on 2020-08 with total page 251 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book is a technical introduction to additive manufacturing (AM) with a focus on powder bed fusion and metals. It provides the theory and industry-based practices to design, make, and test metal components via AM. After outlining the methods and materials of powder bed methods, the book explains the workings and physical limitations of electron beam and laser melt technologies in manufacturing parts, using a variety of metal powders. In this context, the physics of powder melting is described, as well as the effects of temperature variables on the properties of a part. The critical elements of how powder feedstock is chosen and formulated are explained. Processing methods are described using original design and engineering parameters developed by the author. Information is provided on current test methods of metals produced by AM, as well as how to carry out quality control, monitor reliability, and implement safety standards. For process design, a section is devoted to modeling.Each chapter includes a set of problems for students and practitioners that reflect metals' fabrication in industry.
Download or read book Fundamentals of Laser Powder Bed Fusion of Metals written by Igor Yadroitsev and published by Elsevier. This book was released on 2021-05-23 with total page 678 pages. Available in PDF, EPUB and Kindle. Book excerpt: Laser powder bed fusion of metals is a technology that makes use of a laser beam to selectively melt metal powder layer-by-layer in order to fabricate complex geometries in high performance materials. The technology is currently transforming aerospace and biomedical manufacturing and its adoption is widening into other industries as well, including automotive, energy, and traditional manufacturing. With an increase in design freedom brought to bear by additive manufacturing, new opportunities are emerging for designs not possible previously and in material systems that now provide sufficient performance to be qualified in end-use mission-critical applications. After decades of research and development, laser powder bed fusion is now enabling a new era of digitally driven manufacturing. Fundamentals of Laser Powder Bed Fusion of Metals will provide the fundamental principles in a broad range of topics relating to metal laser powder bed fusion. The target audience includes new users, focusing on graduate and undergraduate students; however, this book can also serve as a reference for experienced users as well, including senior researchers and engineers in industry. The current best practices are discussed in detail, as well as the limitations, challenges, and potential research and commercial opportunities moving forward. Presents laser powder bed fusion fundamentals, as well as their inherent challenges Provides an up-to-date summary of this advancing technology and its potential Provides a comprehensive textbook for universities, as well as a reference for industry Acts as quick-reference guide
Download or read book Handbook of Non Ferrous Metal Powders written by Oleg D Neikov and published by Elsevier. This book was released on 2009-02-24 with total page 644 pages. Available in PDF, EPUB and Kindle. Book excerpt: The manufacture and use of the powders of non-ferrous metals has been taking place for many years in what was previously Soviet Russia, and a huge amount of knowledge and experience has built up in that country over the last forty years or so. Although accounts of the topic have been published in the Russian language, no English language account has existed until now. Six prominent academics and industrialists from the Ukraine and Russia have produced this highly-detailed account which covers the classification, manufacturing methods, treatment and properties of the non-ferrous metals ( aluminium, titanium, magnesium, copper, nickel, cobalt, zinc, cadmium, lead, tin, bismuth, noble metals and earth metals). The result is a formidable reference source for those in all aspects of the metal powder industry. Covers the manufacturing methods, properties and importance of the following metals: aluminium, titanium, magnesium, copper, nickel, cobalt, zinc, cadmium, noble metals, rare earth metals, lead, tin and bismuth Expert Russian team of authors, all very experienced English translation and update of book previously published in Russian
Download or read book Metallic Powders for Additive Manufacturing written by Enrique J. Lavernia and published by John Wiley & Sons. This book was released on 2024-02-02 with total page 613 pages. Available in PDF, EPUB and Kindle. Book excerpt: Metallic Powders for Additive Manufacturing Overview of successful pathways for producing metal powders for additive manufacturing of high-performance metallic parts and components with tailored properties Metallic Powders for Additive Manufacturing introduces the readers to the science and technology of atomized metal powders beyond empirical knowledge and the fundamental relationships among the chemistry, microstructure, and morphology of atomized metallic powders and their behavior during additive manufacturing. The text sets a foundation of the underlying science that controls the formation and microstructure of atomized metallic droplets, including the relations among the properties of metallic powders, their performance during the manufacturing processes, and the resulting products. Other topics covered include the influence of powder on defect formation, residual stress, mechanical behavior, and physical properties. The concluding two chapters encompass considerations of broader societal implications and overarching themes, including the exploration of alternative feedstock materials, economic analysis, and sustainability assessment. These chapters offer valuable perspectives on the prospective trajectory of the field. Written by a team of experienced and highly qualified professors and academics, Metallic Powders for Additive Manufacturing includes information on: Atomization techniques such as Vacuum Induction Gas Atomization (VIGA), Electrode Induction Melting Gas Atomization (EIMGA), and Plasma Rotating Electrode Process (PREP) Atomization science and technology, covering control of atomization parameters, powder size distribution, effect of processing variables, and theoretical models of atomization Heat transfer and solidification of droplets, covering nucleation, microstructure development, and important thermal and solidification conditions during atomization Atomization of Al, Fe, Ni, Co, Ti, and high entropy alloys, as well as composite powders for additive manufacturing, and guidelines for atomization equipment and powder handling Fundamental processing principles in a variety of metal additive manufacturing processes Powder characteristics and requirements for different additive manufacturing processes Effect of powder chemistry and physical characteristics on additive manufacturing processes, and the microstructure and properties of the built parts Evaluation of alternative feedstock sources for metal additive manufacturing, beyond gas atomized powder Economic and sustainability perspectives on powder production and additive manufacturing Metallic Powders for Additive Manufacturing is an excellent combination of rigorous fundamentals and a practice-oriented and forward-looking resource on the subject for materials scientists and practicing engineers seeking to understand, optimize, and further develop the field of powder production and additive manufacturing.
Download or read book Properties of Metal Powders for Additive Manufacturing written by U.s. Department of Commerce and published by CreateSpace. This book was released on 2014-07-23 with total page 28 pages. Available in PDF, EPUB and Kindle. Book excerpt: This report is the second in a series of reports from the National Institute of Standards and Technology's (NIST's) Engineering Laboratory project titled Materials Standards for Additive Manufacturing. This project provides the measurement science for the additive manufacturing (AM) industry to measure material properties in a standardized way. Currently there are few consensus-based standards in this area. This project, in conjunction with NIST's Fundamental Measurement Science for Additive Processes project, will provide the technical foundation necessary to develop new consensus-based standards. Development of standards will be done via ASTM-International's (hereafter referred to as 'ASTM') Committee F42 on Additive Manufacturing Technologies and the newly formed International Organization for Standardization (ISO) TC261 committee on Additive Manufacturing.
Download or read book Additive Manufacturing of Titanium Alloys written by Bhaskar Dutta and published by Butterworth-Heinemann. This book was released on 2016-06-17 with total page 96 pages. Available in PDF, EPUB and Kindle. Book excerpt: Additive Manufacturing of Titanium Alloys: State of the Art, Challenges and Opportunities provides alternative methods to the conventional approach for the fabrication of the majority of titanium components produced via the cast and wrought technique, a process which involves a considerable amount of expensive machining. In contrast, the Additive Manufacturing (AM) approach allows very close to final part configuration to be directly fabricated minimizing machining cost, while achieving mechanical properties at least at cast and wrought levels. In addition, the book offers the benefit of significant savings through better material utilization for parts with high buy-to-fly ratios (ratio of initial stock mass to final part mass before and after manufacturing). As titanium additive manufacturing has attracted considerable attention from both academicians and technologists, and has already led to many applications in aerospace and terrestrial systems, as well as in the medical industry, this book explores the unique shape making capabilities and attractive mechanical properties which make titanium an ideal material for the additive manufacturing industry. Includes coverage of the fundamentals of microstructural evolution in titanium alloys Introduces readers to the various Additive Manufacturing Technologies, such as Powder Bed Fusion (PBF) and Directed Energy Deposition (DED) Looks at the future of Titanium Additive Manufacturing Provides a complete review of the science, technology, and applications of Titanium Additive Manufacturing (AM)
Download or read book Laser Additive Manufacturing of High Performance Materials written by Dongdong Gu and published by Springer. This book was released on 2015-04-21 with total page 322 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book entitled “Laser Additive Manufacturing of High-Performance Materials” covers the specific aspects of laser additive manufacturing of high-performance new materials components based on an unconventional materials incremental manufacturing philosophy, in terms of materials design and preparation, process control and optimization and theories of physical and chemical metallurgy. This book describes the capabilities and characteristics of the development of new metallic materials components by laser additive manufacturing process, including nanostructured materials, in situ composite materials, particle reinforced metal matrix composites, etc. The topics presented in this book, similar as laser additive manufacturing technology itself, show a significant interdisciplinary feature, integrating laser technology, materials science, metallurgical engineering and mechanical engineering. This is a book for researchers, students, practicing engineers and manufacturing industry professionals interested in laser additive manufacturing and laser materials processing. Dongdong Gu is a Professor at College of Materials Science and Technology, Nanjing University of Aeronautics and Astronautics (NUAA), PR China.
Download or read book Additive Manufacturing of Metals written by John O. Milewski and published by Springer. This book was released on 2017-06-28 with total page 351 pages. Available in PDF, EPUB and Kindle. Book excerpt: This engaging volume presents the exciting new technology of additive manufacturing (AM) of metal objects for a broad audience of academic and industry researchers, manufacturing professionals, undergraduate and graduate students, hobbyists, and artists. Innovative applications ranging from rocket nozzles to custom jewelry to medical implants illustrate a new world of freedom in design and fabrication, creating objects otherwise not possible by conventional means. The author describes the various methods and advanced metals used to create high value components, enabling readers to choose which process is best for them. Of particular interest is how harnessing the power of lasers, electron beams, and electric arcs, as directed by advanced computer models, robots, and 3D printing systems, can create otherwise unattainable objects. A timeline depicting the evolution of metalworking, accelerated by the computer and information age, ties AM metal technology to the rapid evolution of global technology trends. Charts, diagrams, and illustrations complement the text to describe the diverse set of technologies brought together in the AM processing of metal. Extensive listing of terms, definitions, and acronyms provides the reader with a quick reference guide to the language of AM metal processing. The book directs the reader to a wealth of internet sites providing further reading and resources, such as vendors and service providers, to jump start those interested in taking the first steps to establishing AM metal capability on whatever scale. The appendix provides hands-on example exercises for those ready to engage in experiential self-directed learning.
Download or read book Powder Metallurgy written by Leszek A. Dobrzański and published by BoD – Books on Demand. This book was released on 2017-03-29 with total page 396 pages. Available in PDF, EPUB and Kindle. Book excerpt: The book presents the fundamentals and the role of powder metallurgy in contemporary technologies and the state of the art of classical powder metallurgy technologies and a general description of new variants and special and hybrid technologies used in powder metallurgy. The next part includes over a dozen case studies provided in the following chapters, comprehensively describing authors' accomplishments of numerous teams from different countries across the world in advanced research areas relating to powder metallurgy and to special and hybrid technologies. The detailed information, largely deriving from own and original research and R
Download or read book Metal Powder Additive Manufacturing written by Anatoliy Popovich and published by . This book was released on 2016 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: The beginning of the chapter is devoted to methods of receiving of metal powders-initial components for metal additive manufacturing. Initial materials are very important part of manufacturing, because their quality has an influence on stability of production process and quality of final product. There are various methods of metal powder synthesis. They may be separated conventionally on physical-chemical and mechanical ones. The physical-chemical methods are associated with physical and chemical transformations, and chemical composition and structure of the final product (metal powder) significantly differ from raw materials. The mechanical methods include various types of milling processes and jet dispersion melts by high pressure of gas or liquid (atomization). It is shown that the typical methods of quantitative estimation of powdered materials and some parameters for alloys that already were used in additive technologies. The next theme of the chapter is a review of additive technologies, initial materials for that is metal powders. At this moment, there are three main technologies that have found wide use for the production of metal parts from metal powders: binder jetting, directed energy deposition, and powder bed fusion. Each of them has unique peculiarity, advantages, and limitations that will be presented in the chapter.
Download or read book Materials Technology Gaps in Metal Additive Manufacturing written by Cynthia Waters and published by SAE International. This book was released on 2018-04-24 with total page 154 pages. Available in PDF, EPUB and Kindle. Book excerpt: Metal additive manufacturing (MAM) is an exciting emergent technology that offers the possibility of democratizing metal manufacturing worldwide. Many believe it has the ability to revolutionize product manufacturing on a global scale. MAM will require a considerable design shift for manufacturers and, hence, will disrupt conventional thinking and require adaptation. Visionaries in the mobility industry can see the transformative possibilities after materials considerations are addressed./ Materials Technology Gaps in Metal Additive Manufacturing introduces the reader to various opportunities and relationships in the study of material technologies involved in metal-based additive manufacturing of aerospace and automotive parts. Everything starts and ends with the material feedstock, and the intermediate processes that affect a particular metal. Each of the choices in the complex integrated MAM system impacts final-part properties. Edited by Dr. Cynthia K. Waters, from North Carolina A&T State University, Materials Technology Gaps in Metal Additive Manufacturing is a highly curated collection of 10 seminal SAE International papers. They discuss the various technologies involved in MAM, and draw attention to the materials needs in each of the situations addressed. The main topics included in Materials Technology Gaps in Metal Additive Manufacturing are: Process design and material modeling Metal powder selection and study Additive processing parameters' effect on materials properties As more interdependencies of material properties and possible manufacturing processes evolve (compatibility interdependence), questions if the specific manufacturing process is capable to create the required geometry will also arise. Materials Technology Gaps in Metal Additive Manufacturing brings innovative ways to address these and other challenges that are always present in the adoption of novel technologies.
Download or read book Additive Manufacturing of Metals The Technology Materials Design and Production written by Li Yang and published by Springer. This book was released on 2017-05-11 with total page 172 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book offers a unique guide to the three-dimensional (3D) printing of metals. It covers various aspects of additive, subtractive, and joining processes used to form three-dimensional parts with applications ranging from prototyping to production. Examining a variety of manufacturing technologies and their ability to produce both prototypes and functional production-quality parts, the individual chapters address metal components and discuss some of the important research challenges associated with the use of these technologies. As well as exploring the latest technologies currently under development, the book features unique sections on electron beam melting technology, material lifting, and the importance this science has in the engineering context. Presenting unique real-life case studies from industry, this book is also the first to offer the perspective of engineers who work in the field of aerospace and transportation systems, and who design components and manufacturing networks. Written by the leading experts in this field at universities and in industry, it provides a comprehensive textbook for students and an invaluable guide for practitioners
Download or read book Additive Manufacturing Handbook written by Adedeji B. Badiru and published by CRC Press. This book was released on 2017-05-19 with total page 928 pages. Available in PDF, EPUB and Kindle. Book excerpt: Theoretical and practical interests in additive manufacturing (3D printing) are growing rapidly. Engineers and engineering companies now use 3D printing to make prototypes of products before going for full production. In an educational setting faculty, researchers, and students leverage 3D printing to enhance project-related products. Additive Manufacturing Handbook focuses on product design for the defense industry, which affects virtually every other industry. Thus, the handbook provides a wide range of benefits to all segments of business, industry, and government. Manufacturing has undergone a major advancement and technology shift in recent years.
Download or read book Laser Additive Manufacturing written by Milan Brandt and published by Woodhead Publishing. This book was released on 2016-09-01 with total page 500 pages. Available in PDF, EPUB and Kindle. Book excerpt: Laser Additive Manufacturing: Materials, Design, Technologies, and Applications provides the latest information on this highly efficient method of layer-based manufacturing using metals, plastics, or composite materials. The technology is particularly suitable for the production of complex components with high precision for a range of industries, including aerospace, automotive, and medical engineering. This book provides a comprehensive review of the technology and its range of applications. Part One looks at materials suitable for laser AM processes, with Part Two discussing design strategies for AM. Parts Three and Four review the most widely-used AM technique, powder bed fusion (PBF) and discuss other AM techniques, such as directed energy deposition, sheet lamination, jetting techniques, extrusion techniques, and vat photopolymerization. The final section explores the range of applications of laser AM. Provides a comprehensive one-volume overview of advances in laser additive manufacturing Presents detailed coverage of the latest techniques used for laser additive manufacturing Reviews both established and emerging areas of application
