Download or read book Film Condensation of Steam on Externally Finned Horizontal Tubes written by Frederick A. Flook and published by . This book was released on 1985 with total page 147 pages. Available in PDF, EPUB and Kindle. Book excerpt: Filmwise condensation measurements of steam were made on horizontal finned tubes under vacuum and near-atmospheric conditions. Data were obtained for copper tubes with fins of rectangular, triangular, trapezoidal, and parabolic cross sections, and for a commercially-available finned tube. A stainless steel finned tube was also tested to investigate the effect of thermal conductivity. Maximum enhancements of about 4.8 were obtained under vacuum conditions, and about 6.9 at atmospheric pressure, compared to a smooth tube having an outside diameter equal to the root diameter of the finned tubes. The optimum fin spacing was found to be about 2.0 mm for rectangularly shaped-fins with a fin-thickness of 1.0 mm, and fin height of 0.5 and 1.5 mm. Fins with a parabolic shape were shown to perform better than fins of rectangular shape, and fins were shown to degrade the performance of stainless steel tubes. The effects of vapor shear were also shown to have only a small influence on the steam-side heat transfer coefficient. A theoretical model proposed by Webb et al. was found to underpredict the experimental data. Several suggestions to modify this model are described. Keywords: External fin; Heat transfer coefficient; Enhancement, Condenser tubes (Theses).
Download or read book Film Condensation of Steam on Externally Finned Horizontal Tubes written by and published by . This book was released on 1985 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: Filmwise condensation measurements of steam were made on horizontal finned tubes under vacuum and near-atmospheric conditions. Data were obtained for copper tubes with fins of rectangular, triangular, trapezoidal, and parabolic cross sections, and for a commercially-available finned tube. A stainless steel finned tube was also tested to investigate the effect of thermal conductivity. Maximum enhancements of about 4.8 were obtained under vacuum conditions, and about 6.9 at atmospheric pressure, compared to a smooth tube having an outside diameter equal to the root diameter of the finned tubes. The optimum fin spacing was found to be about 2.0 mm for rectangularly shaped-fins with a fin-thickness of 1.0 mm, and fin height of 0.5 and 1.5 mm. Fins with a parabolic shape were shown to perform better than fins of rectangular shape, and fins were shown to degrade the performance of stainless steel tubes. The effects of vapor shear were also shown to have only a small influence on the steam-side heat transfer coefficient. A theoretical model proposed by Webb et al. was found to underpredict the experimental data. Several suggestions to modify this model are described. Keywords: External fin; Heat transfer coefficient; Enhancement, Condenser tubes (Theses).
Download or read book Filmwise Condensation of Steam on Externally Finned Horizontal Tubes written by William M. Poole and published by . This book was released on 1983 with total page 86 pages. Available in PDF, EPUB and Kindle. Book excerpt: The film-condensation characteristics of a smooth tube and six externally-finned tubes having fins 1 mm high and 1 mm thick, and ptiches of 1.5, 2.0, 2.5, 3.0, 5.0, and 10.0 mm, were experimentally tested. A smooth copper tube with an active length of 133.5 mm, an outside diameter of 19.05 mm, and an inside diameter of 12.7 mm was first tested to correlate the inside heat-transfer coefficient using the Sieder-Tate equation. The leading coefficient for this equation was found to be 0.034 + or - 0.001, and was used to derive the external condensing coefficient for all of the tubes by subtracting the inside and wall resistances from the measured overall resistance. The condensing coefficient was measured, both at atmospheric pressure and vacuum (84 mm hg), with the heat flux as a variable. Condensation data taken for the smooth tube were compared with data in the literature to check the reliability of the apparatus and the data-reduction procedures. The data for the finned tubes showed an optimum pitch of 2.5 mm. (Author).
Download or read book Film Condensation of Steam on Externally Enhanced Horizontal Tubes written by Evagelos S. Mitrou and published by . This book was released on 1986 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: Heat-transfer measurements were made for filmwise condensation of steam on externally enhanced horizontal tubes under vacuum and at atmospheric pressure. Data were obtained for copper tubes with circular fins of rectangular, triangular, trapezoidal, and parabolic cross sections for spiral fins of triangular cross section, for commercially available finned tubes and for wire-wrapped tubes. Four spirally finned tubes from each of Cu, Cu-ni, A1 and stainless steel and two tubes with fins of rectangular cross section from each of Cu-Ni and A1 were manufactured and tested to investigate the effect of thermal conductivity. Among sprially finned tubes, the optimum fin pitch was found to be 1.6 mm. The tubes with a parabolic fin shape showed the best performance with steam-side enhancements of 4.1 and 6.2 under vacuum and at the atmospheric pressure respectively. Enhancement ratios as high as 3.5 and 2.1 were obtained under vacuum and at atmospheric pressure, respectively, for the commercially available finned tubes. The heat-transfer performance decreased with decreasing tube metal thermal conductivity. For the wire-wrapped tubes, an optimum pitch to wire diameter ratio of about 5.1 was found, with steam-side enhancements of about 1.9 and 2.2 under vacuum and at atmospheric pressure, respectively. A recent theoretical analysis of laminar film of low-surface-tension fluids on wire-wrapped tubes was modified to include the condensate retention of the tube due to the high surface tension of water. Agreement between this modified analysis and the experimental data was favorable. Keywords: Heat transfer coefficient.
Download or read book Some Aspects of Film Condensation of Steam on Finned Tubes written by James M. Coumes and published by . This book was released on 1989 with total page 148 pages. Available in PDF, EPUB and Kindle. Book excerpt: Heat-transfer measurements were made for filmwise condensation of steam on smooth tubes and finned tubes with rectangular-shaped fins. The influence of fin root diameter on a single horizontal finned tube was examined by taking data for two families of tubes whose fin root diameters were 12.7 and 19.05 mm. Each family of tubes had fins that were 1 mm thick and 1 mm high, but with fin spacings of 0.25, 0.50, 1.0, 1.5, 2.0, and 4.0 mm. To compare results being obtained in a concurrent research project with Queen Mary College (University of London), data were collected on two tubes whose fin root diameters were 12.7 mm, and which had fin thickness of 0.5 mm, fin heights of 1.59 mm, and fin spacings of 1.0 mm. A comparison of the enhancement ratios (based on constant vapor-side temperature drop) with past Naval Postgraduate School (nps) studies showed good agreement. The apparatus was then modified in order to study the effects of condensate inundation.
Download or read book Effect of Fin Height on Film Condensation of Steam on Stainless Steel Integral fin Tubes written by George A. Incheck and published by . This book was released on 1995 with total page 308 pages. Available in PDF, EPUB and Kindle. Book excerpt: Condensation heat transfer performance on a series of horizontal stainless-steel integral-fin tubes was experimentally studied at both atmospheric and vacuum pressure conditions to examine the effects of fin height on tubes of low thermal conductivity. Eight tubes with rectangular fin heights ranging from 0.16 to 1.42 mm and a smooth tube were tested. The fin thickness and spacing and tube inside and root diameters were kept constant at 1.0, 1.5, 13.1, and 14.2 mm respectively. The overall heat transfer coefficient was determined from experimentation and the outside heat transfer coefficient was then determined using the modified Wilson plot technique. A fin height of approximately 0.30 mm provided the maximum heat transfer at both vacuum and atmospheric conditions. Heat transfer performance declined steadily for further increases in fin height. The experimental results were compared to the predictions of the Beatty and Katz and Briggs and Rose models. Neither model satisfactorily predicted performance for the full range of fin heights tested.
Download or read book The Influence of Wall Conductivity on Film Condensation with Integral Fin Tubes written by Robert Lee Cobb and published by . This book was released on 1993 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: Heat transfer performance of steam condensing on horizontal finned tubes made of copper, aluminum, copper nickel(90/10), and stainless steel(316) was studied using a condenser test rig at both vacuum and atmospheric conditions. Integral fin tubes included conventional rectangular shaped fins as well as rectangular fins having a radiussed root geometry (ie, a fillet radius equal to half the fin spacing). All finned tubes had inner and outer diameters of 12.70mm and 15.88mm respectively, and had a fin thickness of l.0mm and a fin spacing of 1.5mm. The overall heat transfer coefficient (U sub o) was determined experimentally and the outside heat transfer coefficient (ho) was obtained utilizing a modified Wilson Plot procedure. Results indicated that the performance of a finned tube was strongly dependent on the tube material and weakly dependent on fin geometry. Radiussing the fin root to remove condensate between fins in the unflooded portion (ie, top portion) of a finned tube reduced the heat transfer performance compared to a conventional rectangular shaped integral fin. Experimental data were compared to the models of Beatty and Katz as well as to a modified model of Rose.
Download or read book Filmwise Condensation of Steam on Low Integral Finned Tubes written by Ioannis V. Georgiadis and published by . This book was released on 1984 with total page 167 pages. Available in PDF, EPUB and Kindle. Book excerpt: Filmwise condensation heat-transfer measurements of steam were made on horizontal tubes under vacuum and near-atmospheric pressures. Data were taken for smooth tube and for 21 tubes which contained rectangularly-shaped, low integral fins. The fin geometry was systematically varied in order to investigate the dependence of the steam-side heat-transfer coefficient on fin spacing, thickness and height. The condensation process was found to be most sensitive to fin spacing and to be weakly dependent on fin thickness. When the fin height was increased from 1.0 to 2.0 mm, the increase in the heat-transfer coefficient was about 20 percent, while the increase in condensing area was 51 percent. The best performing finned tube had a fin height of 1.5 mm, a fin thickness of 1.0 mm and a fin height of 2.0 mm. It showed an enhancement over the smooth tube of between 4 to 5 under vacuum conditions and around 6 at atmospheric conditions. Thus, the use of finned tubes may result in a significant reduction in size and weight of present-day steam condensers. Originator-supplied key words include: Steam, Condensation, Filmwise, Tube, Low Integral Fin, Heat-Transfer Coefficient, Enhancement.
Download or read book Further Studies in Filmwise Condensation of Steam on Horizontal Finned Tubes written by Keith Andrew Swensen and published by . This book was released on 1992 with total page 127 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Handbook of Thermal Science and Engineering written by and published by Springer. This book was released on 2018-07-31 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This Handbook provides researchers, faculty, design engineers in industrial R&D, and practicing engineers in the field concise treatments of advanced and more-recently established topics in thermal science and engineering, with an important emphasis on micro- and nanosystems, not covered in earlier references on applied thermal science, heat transfer or relevant aspects of mechanical/chemical engineering. Major sections address new developments in heat transfer, transport phenomena, single- and multiphase flows with energy transfer, thermal-bioengineering, thermal radiation, combined mode heat transfer, coupled heat and mass transfer, and energy systems. Energy transport at the macro-scale and micro/nano-scales is also included. The internationally recognized team of authors adopt a consistent and systematic approach and writing style, including ample cross reference among topics, offering readers a user-friendly knowledgebase greater than the sum of its parts, perfect for frequent consultation. The Handbook of Thermal Science and Engineering is ideal for academic and professional readers in the traditional and emerging areas of mechanical engineering, chemical engineering, aerospace engineering, bioengineering, electronics fabrication, energy, and manufacturing concerned with the influence thermal phenomena.
Download or read book Scientific and Technical Aerospace Reports written by and published by . This book was released on 1992 with total page 1572 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Film Vapour Condensations on Horizontal Small Finned Tubes written by V. A. Kharkhu and published by . This book was released on 1971 with total page 13 pages. Available in PDF, EPUB and Kindle. Book excerpt: The report describes vapor film condensation on a horizontal tube with transverse trapezoid fins under the influence of surface tension. Experimental data are given for heat transfer of water and Freon-113 vapors, which are in a good agreement with the theoretical data. It is shown that the rate of vapour condensation may be increased by 1.5-2 times due to the action of surface forces. (Author).
Download or read book Condensation of Vapors on Outside of Finned Tubes written by Kenneth Orion Beatty and published by . This book was released on 1948 with total page 24 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Heat Transfer in Condensation and Boiling written by Karl Stephan and published by Springer Science & Business Media. This book was released on 2013-06-29 with total page 342 pages. Available in PDF, EPUB and Kindle. Book excerpt: I welcome the opportunity to have my book translated, because of the great emphasis on two-phase flow and heat transfer in the English-speaking world, as related to research, university education, and industrial practice. The 1988 Springer-Verlag edition of "Warmeiibergang beim Kondensieren und beim Sieden" has been enlarged to include additional material on falling film evaporation (Chapter 12) and pressure drop in two-phase flow (Chapter 13). Minor errors in the original text have also been corrected. I would like to express my sincere appreciation to Professor Green, Asso ciate Professor of German at Rensselaer, for his excellent translation and co operation. My thanks go also to Professor Bergles for his close attention to technical and linguistic details. He carefully read the typescript and made many comments and suggestions that helped to improve the manuscript. I hope that the English edition will meet with' a favorable reception and contribute to better understanding and to progress in the field of heat transfer in condensation and boiling. February 1992 K. Stephan Preface to the German-Language Edition This book is a continuation of the series "Heat and Mass Transfer" edited by U. Grigull, in which three volumes have already been published. Its aim is to acquaint students and practicing engineers with heat transfer during condensa tion and boiling, and is intended primarily for students and engineers in mechanical, chemical, electrical, and industrial processing engineering.
Download or read book Further Developments of Filmwise Condensation of Steam on Horizontal Integral Finned Tubes written by Mark Brady Guttendorf and published by . This book was released on 1990 with total page 170 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book CONDENSATION OF STEAM ON MULTIPLE HORIZONTAL TUBES written by and published by . This book was released on 2004 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: The problem of condensation of steam on a vertical tier of horizontal tubes is investigated by both analytical and experimental methods in this study. A computer program is written to perform the analysis of laminar film condensation on the horizontal tubes. The program is capable to calculate condensate film thickness and velocity distribution, as well as the heat transfer coefficient within the condensate. An experimental setup was also manufactured to observe the condensation phenomenon. Effects of tube diameter and temperature difference between steam and the tube wall on condensation heat transfer have been analytically investigated with the computer program. Experiments were carried out at different inclinations of the tier of horizontal tubes. Effects of the steam velocity and the distance between the horizontal tubes are also experimentally investigated. Results of the experiments are compared to those of the studies of Abdullah et al., Kumar et al. and Nusselt as well as to the analytical results of the present study.
Download or read book Masters Theses in the Pure and Applied Sciences written by Wade H. Shafer and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 386 pages. Available in PDF, EPUB and Kindle. Book excerpt: Masters Theses in the Pure and Applied Sciences was first conceived, published, and disseminated by the Center for Information and Numerical Data Analysis and Synthesis (CINDAS) * at Purdue University in 1957, starting its coverage of theses with the academic year 1955. Beginning with Volume 13, the printing and dissemination phases of the activity were transferred to University Microfilms/Xerox of Ann Arbor, Michigan, with the thougtit that such an arrangement would be more beneficial to the academic and general scientific and technical community. After five years of this joint undertaking we had concluded that it was in the interest of all con cerned if the printing and distribution of the volumes were handled by an interna tional publishing house to assure improved service and broader dissemination. Hence, starting with Volume 18, Masters Theses in the Pure and Applied Sciences has been disseminated on a worldwide basis by Plenum Publishing Cor poration of New York, and in the same year the coverage was broadened to include Canadian universities. All back issues can also be ordered from Plenum. We have reported in Volume 31 (thesis year 1986) a total of 11 ,480 theses titles trom 24 Canadian and 182 United States universities. We are sure that this broader base tor these titles reported will greatly enhance the value ot this important annual reterence work. While Volume 31 reports theses submitted in 1986, on occasion, certain univer sities do re port theses submitted in previousyears but not reported at the time.
