Download or read book Dynamic Deformations and Analysis of a Metal Matrix Composite written by Brad Stewart Altman and published by . This book was released on 1992 with total page 364 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Inelasticity and Micromechanics of Metal Matrix Composites written by George Voyiadjis and published by Elsevier. This book was released on 2017-05-04 with total page 358 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book contains fifteen papers based on the presentations made at the symposium on "Inelasticity and Micromechanics of Metal Matrix Composites" held at the University of Washington, USA, in mid-1994. The papers represent the most recent work conducted on inelasticity and micromechanics of metal matrix composites. The book is divided into two parts: Part I deals with the study of inelastic deformation in metal matrix composites, while Part II tackles the micromechanical aspects of metal matrix composites. The articles discuss different aspects of these two topics ranging from purely theoretical treatments to extensive experimental investigations. Many of the papers are by prominent researchers working in this area.

Download or read book Deformation and Failure of Metal Matrix Composites Under Dynamic Loads written by and published by . This book was released on 1996 with total page 75 pages. Available in PDF, EPUB and Kindle. Book excerpt: SRI International conducted a three-year program of experiments, microstructural examinations, and analysis to determine the rate sensitivity of deformation and failure of metal-matrix composites (MMC) and to understand and model the role of interfaces and constituents on dynamic failure. Silicon-carbide fiber reinforced Timetal 21S and Ti-15-3 matrices in three heat treatment conditions were studied. The work included dynamic fiber pushout experiments to measure dynamic interface strength, notched three-point-bend experiments with acoustic emission sensors to determine the static fracture resistance, and notched one-point-bend experiments to determine dynamic fracture resistance. Microstructural examinations were performed on transverse and longitudinal cross sections. The nature of interface failure, fiber failure, and matrix failure was established. A key finding was that toughening from fiber bridging is not obtained under bending loads. In bending, fibers fail well in advance of the crack tip and are thereby prevented from bridging matrix cracks. A two-dimensional finite element model of the composite was developed in which fibers, matrix, and interfaces in the vicinity of the notch root were modeled explicitly. The model can be used in parameter studies to investigate changes in interface and constituent properties, and loading rate, and hence assist in designing MMCs having tailored combinations of strength, toughness, and, particularly, greater resistance to bend failure.

Download or read book Advances in Damage Mechanics Metals and Metal Matrix Composites written by George Voyiadjis and published by Elsevier. This book was released on 2012-12-02 with total page 558 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book provides in a single and unified volume a clear and thorough presentation of the recent advances in continuum damage mechanics for metals and metal matrix composites. Emphasis is placed on the theoretical formulation of the different constitutive models in this area, but sections are added to demonstrate the applications of the theory. In addition, some sections contain new material that has not appeared before in the literature. The book is divided into three major parts: Part I deals with the scalar formulation and is limited to the analysis of isotropic damage in materials; Parts II and III deal with the tensor formulation and is applied to general states of deformation and damage. The material appearing in this text is limited to plastic deformation and damage in ductile materials (e.g. metals and metal matrix composites) but excludes many of the recent advances made in creep, brittle fracture, and temperature effects since the authors feel that these topics require a separate volume for this presentation. Furthermore, the applications presented in this book are the simplest possible ones and are mainly based on the uniaxial tension test.

Download or read book Dynamic Deformation Damage and Fracture in Composite Materials and Structures written by Vadim Silberschmidt and published by Elsevier. This book was released on 2022-09-15 with total page 666 pages. Available in PDF, EPUB and Kindle. Book excerpt: Dynamic Deformation, Damage and Fracture in Composite Materials and Structures, Second Edition reviews various aspects of dynamic deformation, damage and fracture, mostly in composite laminates and sandwich structures, and in a broad range of application areas including aerospace, automotive, defense and sports engineering. This book examines low- and high-velocity loading and assesses shock, blast and penetrative events, and has been updated to cover important new developments such as the use of additive manufacturing to produce composites, including fiber-reinforced ones. New microstructural, experimental, theoretical, and numerical studies with advanced tools are included as well. The book also features four new chapters covering topics such as dynamic delamination, dynamic deformation and fracture in 3D-printed composites, ballistic impacts with fragmenting projectiles, and the effect of multiple impacting. - Examines dynamic deformation and fracture of composite materials, covering experimental, analytical and numerical aspects - Features four new chapters covering topics such as dynamic interfacial fracture, fracture in 3D-printed composites, ballistic impacts with fragmenting projectiles, and the effect of multiple impacting - Addresses important application areas such as aerospace, automotive, wind energy, defense and sports

Download or read book Metal Matrix Composites written by International Conference on Composite Materials and published by Woodhead Publishing. This book was released on 1993 with total page 940 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Micromechanics and Nanosimulation of Metals and Composites written by Siegfried Schmauder and published by Springer Science & Business Media. This book was released on 2008-10-20 with total page 432 pages. Available in PDF, EPUB and Kindle. Book excerpt: The strength of metallic materials determines the usability and reliability of all the machines, tools and equipment around us. Yet, the question about which mechanisms control the strength and damage resistance of materials and how they can be optimised remains largely unanswered. How do real, heterogeneous ma- rials deform and fail? Why can a small modification of the microstructure increase the strength and damage resistance of materials manifold? How can the strength of heterogeneous materials be predicted? The purpose of this book is to present different experimental and computational analysis methods of micromechanics of damage and strength of materials and to demonstrate their applications to various micromechanical problems. This book summarizes at a glance some of the publications of the Computational Mechanics Group at the IMWF/MPA Stuttgart, dealing with atomistic, micro- and meso- chanical modelling and experimental analysis of strength and damage of metallic materials. In chapter 1, the micromechanisms of damage and fracture in different groups of materials are investigated experimentally, using direct observations and inverse analysis. The interaction of microstructural elements with the evolving damage is studied in these experiments. Chapter 2 presents different approaches to the - cromechanical simulation of composite materials: embedded unit cells, multiphase finite elements and multiparticle unit cells. Examples of the application of these models to the analysis of deformation and damage in different materials are given. Chapter 3 deals with the methods of numerical modelling of damage evolution and crack growth in heterogeneous materials.

Download or read book Metal Matrix Composites written by W. Steven Johnson and published by ASTM International. This book was released on 1989 with total page 289 pages. Available in PDF, EPUB and Kindle. Book excerpt: Fourteen peer-reviewed papers on testing techniques, analysis approaches, and descriptions of various failure processes. From the Symposium on [title] held at Sparks, NV, April 1988. Annotation copyright Book News, Inc. Portland, Or.

Download or read book An Experimental and Numerical Investigation of Dynamic Deformations in Metal matrix and Tungsten based Composites written by Sunil Yadav and published by . This book was released on 1996 with total page 256 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Carbon Nanotubes written by Andy Nieto and published by CRC Press. This book was released on 2021-05-18 with total page 376 pages. Available in PDF, EPUB and Kindle. Book excerpt: This discovery of carbon nanotubes (CNT) three decades ago ushered in the technological era of nanotechnology. Among the most widely studied areas of CNT research is their use as structural reinforcements in composites. This book describes the development of CNT reinforced metal matrix composites (CNT-MMCs) over the last two decades. The field of CNT-MMCs is abundant in fundamental science, rich in engineering challenges and innovations and ripe for technological maturation and commercialization. The authors have sought to present the current state of the-art in CNT-MMC technology from their synthesis to their myriad potential end-use applications. Specifically, topics explored include: • Advantages, limitations, and evolution of processing techniques used to synthesize and fabricate CNT-MMCs • Emphasizes dispersion techniques of CNTs in metallic systems, a key challenge to the successful and widespread implementation of CNT-MMCs. Methods for quantification and improved control of CNT distributions are presented • Methods for quantification and improved control of CNT distributions are presented • Characterization techniques uniquely suited for charactering these nanoscale materials and their many chemical and physical interactions with the metal matrix, including real-time in-situ characterization of deformation mechanisms • Electron microscope images from premier studies enrich discussions on micro-mechanical modeling, interfacial design, mechanical behavior, and functional properties • A chapter is dedicated to the emergence of dual reinforcement composites that seek to enhance the efficacy of CNTs and lead to material properties by design This book highlights seminal findings in CNT-MMC research and includes several tables listing processing methods, associated CNT states, and resulting properties in order to aid the next generation of researchers in advancing the science and engineering of CNT-MMCs. In addition, a survey of the patent literature is presented in order to shed light on what the first wave of CNT-MMC commercialization may look like and the challenges that will have to be overcome, both technologically and commercially.

Download or read book A Coupled Uncoupled Computational Scheme for Deformation and Fatigue Damage Analysis of Unidirectional Metal Matrix Composites written by TE. Wilt and published by . This book was released on 1997 with total page 18 pages. Available in PDF, EPUB and Kindle. Book excerpt: A fatigue damage computational algorithm utilizing a multiaxial, isothermal, continuum-based fatigue damage model for unidirectional metal-matrix composites has been implemented into the commercial finite element code MARC using MARC user subroutines. Damage is introduced into the finite element solution through the concept of effective stress that fully couples the fatigue damage calculations with the finite element deformation solution. Two applications using the fatigue damage algorithm are presented. First, an axisymmetric stress analysis of a circumferentially reinforced ring, wherein both the matrix cladding and the composite core were assumed to behave elastic-perfectly plastic. Second, a micromechanics analysis of a fiber/matrix unit cell using both the finite element method and the generalized method of cells (GMC). Results are presented in the form of S-N curves and damage distribution plots.

Download or read book Scientific and Technical Aerospace Reports written by and published by . This book was released on 1995 with total page 702 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Inelastic Deformation of Metal Matrix Composites Part 1 Plasticity and Damage Mechanisms written by National Aeronautics and Space Administration (NASA) and published by Createspace Independent Publishing Platform. This book was released on 2018-07-08 with total page 70 pages. Available in PDF, EPUB and Kindle. Book excerpt: The deformation mechanisms of a Ti 15-3/SCS6 (SiC fiber) metal matrix composite (MMC) were investigated using a combination of mechanical measurements and microstructural analysis. The objectives were to evaluate the contributions of plasticity and damage to the overall inelastic response, and to confirm the mechanisms by rigorous microstructural evaluations. The results of room temperature experiments performed on 0 degree and 90 degree systems primarily are reported in this report. Results of experiments performed on other laminate systems and at high temperatures will be provided in a forthcoming report. Inelastic deformation of the 0 degree MMC (fibers parallel to load direction) was dominated by the plasticity of the matrix. In contrast, inelastic deformations of the 90 degree composite (fibers perpendicular to loading direction) occurred by both damage and plasticity. The predictions of a continuum elastic plastic model were compared with experimental data. The model was adequate for predicting the 0 degree response; however, it was inadequate for predicting the 90 degree response largely because it neglected damage. The importance of validating constitutive models using a combination of mechanical measurements and microstructural analysis is pointed out. The deformation mechanisms, and the likely sequence of events associated with the inelastic deformation of MMCs, are indicated in this paper. Majumdar, B. S. and Newaz, G. M. Unspecified Center...

Download or read book Fundamentals of Metal Matrix Composites written by Subra Suresh and published by Elsevier. This book was released on 2013-10-22 with total page 353 pages. Available in PDF, EPUB and Kindle. Book excerpt: `Metal-Matrix Composites' are being used or considered for use in a variety of applications in the automotive, aerospace and sporting goods industries. This book contains sixteen chapters, all written by leading experts in the filed, which focus on the processing, microstructure and characterization, mechanics and micromechanics of deformation, mechanics and micromechanics of damage and fracture, and practical applications of a wide variety of metal composites.A particularly noteworthy feature of this authoritative volume is its collection of state-of-the-art reviews of the relationships among processing, microstructural evolution, micromechanics of deformation and overall mechanical response.

Download or read book Modeling and Analysis of High Temperature Inelastic Deformation in Metal Matrix Composites written by Rahul S. Shah and published by . This book was released on 1991 with total page 393 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Time dependent Deformation of Titanium Metal Matrix Composites written by and published by . This book was released on 1995 with total page 36 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Contemporary Research in Engineering Science written by Romesh C. Batra and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 696 pages. Available in PDF, EPUB and Kindle. Book excerpt: Fatigue failures occur in aerospace,marine,nuclear structures and automobile com ponents from initiation and propagation of cracks from holes,scratches or defects in the material. To design against these failures, crack propagation life and fracture strength need to be accurately predicted. It is reported in the literature, that these failures often initiate as surface cracks, corner cracks and cracks emanating from fastner holes. Such cracks are with elliptic or nearly elliptic in shapes. The deviation from elliptic shape is due to varying constraint effect along the crack front. Even in situations, when the cracks are through the thickness of the material, there would be thicknesswise variation of constraint effects leading to three dimensional nature of crack growth. Accurate predictions of the crack growth in these cases by numerical methods can be made only by solving three-dimensional boundary value problems. Empirical relationships have been developed [1] based on Linear Elastic Fracture Mechanics over years describing fatigue crack growth response. Some of these empirical relationships required modifications in the later stages, to meet the design applications. The Crack closure phenomenon discovered by Elber[2, 3] during the crack growth phase is mainly attributed to the local material yielding near the crack tip and the consequent residual plastic wake behind the crack tip. It helped considerably in understanding several aspects of fatigue crack growth and rewrite these relations.