Download or read book Strain Hardening Due to Machining Austenitic Stainless Steel written by Mohammad Sepahrom and published by . This book was released on 1972 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Reducing Tool Wear When Machining Austenitic Stainless Steels written by T. Kosa and published by . This book was released on 1998 with total page 9 pages. Available in PDF, EPUB and Kindle. Book excerpt: Austenitic stainless steels are considered more difficult to machine than carbon steels due to their high work hardening rate, large spread between yield and ultimate tensile strength, high toughness and ductility, and low thermal conductivity. These characteristics can result in a built-up edge or excessive tool wear during machining, especially when the cutting speed is too high. The practical solution is to lower the cutting speed until tool life reaches an acceptable level. However, lower machining speed negatively impacts productivity. Thus, in order to overcome tool wear at relatively high machining speeds for these alloys, on-going research is being performed to improve cutting fluids, develop more wear-resistant tools, and to modify stainless steels to make them less likely to cause tool wear.
Download or read book Advanced Machining Processes of Metallic Materials written by Wit Grzesik and published by Elsevier. This book was released on 2008-01-22 with total page 489 pages. Available in PDF, EPUB and Kindle. Book excerpt: Advanced Machining Processes of Metallic Materials updates our knowledge on the metal cutting processes in relation to theory and industrial practice. In particular, many topics reflect recent developments, e.g. modern tool materials, computational machining, computer simulation of various process phenomena, chip control, monitoring of the cutting state, progressive and hybrid machining operations, and generation and modelling of surface integrity. This book addresses the present state and future development of machining technologies. It provides a comprehensive description of metal cutting theory, experimental and modelling techniques along with basic machining processes and their effective use in a wide range of manufacturing applications. Topics covered include fundamental physical phenomena and methods for their evaluation, available technology of machining processes for specific classes of materials and surface integrity. The book also provides strategies for optimalization techniques and assessment of machinability. Moreover, it describes topics not currently covered in other sources, such as high performance and multitasking (complete) machining with a high potential for increasing productivity, and virtual and e-machining. The research covered here has contributed to a more generalized vision of machining technology, including not only traditional manufacturing tasks but also new potential (emerging) applications such as micro- and nanotechnology. - Many practical examples of modern machining technology - Applicable for various technical, engineering and scientific levels - Collects together 20 years of research in the field and related technical information
Download or read book Stainless Steels and Alloys written by Zoia Duriagina and published by BoD – Books on Demand. This book was released on 2019-02-13 with total page 160 pages. Available in PDF, EPUB and Kindle. Book excerpt: Materials science is the magic that allows us to change the chemical composition and microstructure of material to regulate its corrosion-mechanical, technological, and functional properties. Five major classes of stainless steels are widely used: ferritic, austenitic, martensitic, duplex, and precipitation hardening. Austenitic stainless steels are extensively used for service down to as low as the temperature of liquid helium (-269oC). This is largely due to the lack of a clearly defined transition from ductile to brittle fracture in impact toughness testing. Steels with ferritic or martensitic structures show a sudden change from ductile (safe) to brittle (unsafe) fracture over a small temperature difference. Even the best of these steels shows this behavior at temperatures higher than -100oC and in many cases only just below zero. Various types of stainless steel are used across the whole temperature range from ambient to 1100oC. This book will be useful to scientists, engineers, masters, graduate students, and students. I hope readers will enjoy this book and that it will serve to create new materials with unique properties.
Download or read book Composites Manufacturing written by Sanjay Mazumdar and published by CRC Press. This book was released on 2001-12-27 with total page 417 pages. Available in PDF, EPUB and Kindle. Book excerpt: More and more companies manufacture reinforced composite products. To meet the market need, researchers and industries are developing manufacturing methods without a reference that thoroughly covers the manufacturing guidelines. Composites Manufacturing: Materials, Product, and Process Engineering fills this void. The author presents a fundamental
Download or read book Machining of Stainless Steels and Super Alloys written by Helmi A. Youssef and published by John Wiley & Sons. This book was released on 2016-01-19 with total page 303 pages. Available in PDF, EPUB and Kindle. Book excerpt: Provides a comprehensive description for machining technologies of stainless steels and super alloys with consideration to current industrial applications. Presents current and recent developments related to traditional and nontraditional machining techniques of stainless steels and super alloys Arranges types of stainless steels and super alloys in qualitative and quantitative form, as related to their machining characteristics, providing the reader with information regarding optimum working condition for each material Proposes a 10-level machinability chart to rank important grades of stainless steels Arranges the machinability rating of the most commonly used super alloys in a descending order Presents non-traditional machining processes along with some hybrid processes which have been applied successfully to stainless steels and super alloys
Download or read book Handbook of Manufacturing Engineering and Technology written by Andrew Y. C. Nee and published by Springer. This book was released on 2014-10-31 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: The Springer Reference Work Handbook of Manufacturing Engineering and Technology provides overviews and in-depth and authoritative analyses on the basic and cutting-edge manufacturing technologies and sciences across a broad spectrum of areas. These topics are commonly encountered in industries as well as in academia. Manufacturing engineering curricula across universities are now essential topics covered in major universities worldwide.
Download or read book Strain Hardening of Austenitic Stainless Steel written by Gordon W. Powell and published by . This book was released on 1955 with total page 35 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Machining and Grinding of Ultrahigh strength Steels and Stainless Steel Alloys written by C. T. Olofson and published by . This book was released on 1967 with total page 220 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Wear Processes in Manufacturing written by Shyam Bahadur and published by ASTM International. This book was released on 1999 with total page 167 pages. Available in PDF, EPUB and Kindle. Book excerpt: Contains papers presented at a May 1998 symposium held in Atlanta, Georgia, in sections on abrasion in ceramic grinding, wear of cutting tools, friction in vibratory conveyors, and erosion in manufacturing. Specific subjects include characterization of wear processes due to material erosion, measuri
Download or read book Superaustenitic Stainless Steels written by Alessio Malandruccolo and published by Springer Nature. This book was released on with total page 293 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Manufacturing and Application of Stainless Steels written by Andrea Di Schino and published by MDPI. This book was released on 2020-04-15 with total page 260 pages. Available in PDF, EPUB and Kindle. Book excerpt: Stainless steels represent a quite interesting material family, both from a scientific and commercial point of view, following to their excellent combination in terms of strength and ductility together with corrosion resistance. Thanks to such properties, stainless steels have been indispensable for the technological progress during the last century and their annual consumption increased faster than other materials. They find application in all these fields requiring good corrosion resistance together with ability to be worked into complex geometries. Despite to their diffusion as a consolidated materials, many research fields are active regarding the possibility to increase stainless steels mechanical properties and corrosion resistance by grain refinement or by alloying by interstitial elements. At the same time innovations are coming from the manufacturing process of such a family of materials, also including the possibility to manufacture them starting from metals powder for 3D printing. The Special Issue scope embraces interdisciplinary work covering physical metallurgy and processes, reporting about experimental and theoretical progress concerning microstructural evolution during processing, microstructure-properties relations, applications including automotive, energy and structural.
Download or read book Handbook of Residual Stress and Deformation of Steel written by George E. Totten and published by ASM International. This book was released on 2002 with total page 496 pages. Available in PDF, EPUB and Kindle. Book excerpt: Annotation Examines the factors that contribute to overall steel deformation problems. The 27 articles address the effect of materials and processing, the measurement and prediction of residual stress and distortion, and residual stress formation in the shaping of materials, during hardening processes, and during manufacturing processes. Some of the topics are the stability and relaxation behavior of macro and micro residual stresses, stress determination in coatings, the effects of process equipment design, the application of metallo- thermo-mechanic to quenching, inducing compressive stresses through controlled shot peening, and the origin and assessment of residual stresses during welding and brazing. Annotation c. Book News, Inc., Portland, OR (booknews.com)
Download or read book Fundamentals of Machining Processes written by Hassan Abdel-Gawad El-Hofy and published by CRC Press. This book was released on 2013-08-06 with total page 565 pages. Available in PDF, EPUB and Kindle. Book excerpt: Completely revised and updated, this second edition of Fundamentals of Machining Processes: Conventional and Nonconventional Processes covers the fundamentals machining by cutting, abrasion, erosion, and combined processes. The new edition has been expanded with two additional chapters covering the concept of machinability and the roadmap for selecting machining processes that meet required design specification. See What’s New in the Second Edition: Explanation of the definition of the relative machinability index and how the machinability is judged Important factors affecting the machinability ratings Machinability ratings of common engineering materials by conventional and nonconventional methods. Factors to be considered when selecting a machining process that meets the design specifications, including part features, materials, product accuracy, surface texture, surface integrity, cost, environmental impacts, and the process and the machine selected capabilities Introduction to new Magnetic Field Assisted Finishing Processes Written by an expert with 37 years of experience in research and teaching machining and related topics, this covers machining processes that range from basic conventional metal cutting, abrasive machining to the most advanced nonconventional and micromachining processes. The author presents the principles and theories of material removal and applications for conventional and nonconventional machining processes, discusses the role of machining variables in the technological characteristics of each process, and provides treatment of current technologies in high speed machining and micromachining. The treatment of the different subjects has been developed from basic principles and does not require the knowledge of advanced mathematics as a prerequisite. A fundamental textbook for undergraduate students, this book contains machining data, solved examples, and review questions which are useful for students and manufacturing engineers.
Download or read book Burrs Analysis Control and Removal written by Jan C. Aurich and published by Springer Science & Business Media. This book was released on 2009-12-01 with total page 249 pages. Available in PDF, EPUB and Kindle. Book excerpt: In many machining operations burrs cannot be avoided. They can affect the functionality and the safe handling of the workpiece in the subsequent processing, and have to be removed by a special deburring process. Toleration of burrs, which are not part of functional edges, depends on their respective shape and size. High inspection effort is necessary to guarantee the workpiece quality. Therefore, the research results on burrs, with a focus on burr analysis and control as well as on cleanability and burr removal based on the presentations held at the conference are valuable for researchers and engineers in manufacturing development.
Download or read book Proceedings of the 8th International Conference on Fracture Fatigue and Wear written by Magd Abdel Wahab and published by Springer Nature. This book was released on 2021-01-12 with total page 756 pages. Available in PDF, EPUB and Kindle. Book excerpt: This proceedings gather a selection of peer-reviewed papers presented at the 8th International Conference on Fracture Fatigue and Wear (FFW 2020), held as a virtual conference on 26–27 August 2020. The contributions, prepared by international scientists and engineers, cover the latest advances in and innovative applications of fracture mechanics, fatigue of materials, tribology, and wear of materials. In addition, they discuss industrial applications and cover theoretical and analytical methods, numerical simulations and experimental techniques. The book is intended for academics, including graduate students and researchers, as well as industrial practitioners working in the areas of fracture fatigue and wear.
Download or read book Uhlig s Corrosion Handbook written by R. Winston Revie and published by John Wiley & Sons. This book was released on 2011-04-12 with total page 1299 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book serves as a reference for engineers, scientists, and students concerned with the use of materials in applications where reliability and resistance to corrosion are important. It updates the coverage of its predecessor, including coverage of: corrosion rates of steel in major river systems and atmospheric corrosion rates, the corrosion behavior of materials such as weathering steels and newer stainless alloys, and the corrosion behavior and engineering approaches to corrosion control for nonmetallic materials. New chapters include: high-temperature oxidation of metals and alloys, nanomaterials, and dental materials, anodic protection. Also featured are chapters dealing with standards for corrosion testing, microbiological corrosion, and electrochemical noise.
