Download or read book Speed Reduction Methods and Studies in Work Zones written by R. F. Benekohal and published by . This book was released on 1992 with total page 82 pages. Available in PDF, EPUB and Kindle. Book excerpt: The objectives of this project were to determine the effectiveness of speed control methods and study traffic behavior in construction zones. This report provides a brief introduction and summary of findings from the following reports which were prepared as part of this study: (1) Evaluation and Summary of Studies in Speed Control Methods in Work Zones. (2) Evaluation of a Radar-Activated Horn System for Speed Control in Highway Maintenance Operations. (3) Survey of Driver's Opinion about Work Zone Traffic Control on a Rural Highway. (4) Speed Reduction Effects of Drone Radar in Rural Interstate Work Zones. (5) Speed Reduction Effects of Changeable Message Signs in a Construction Zone. (6) Effects of Police Presence on Speed in a Highway Work Zone: Circulating Marked Police Car Experiment. (7) Evaluation of Work Zone Speed Limit Signs with Strobe Lights. (8) Speed Reduction Profiles of Vehicles in a Highway Construction zone. Data only for those vehicles in free flow traffic are used for speed reduction evaluation. A vehicle was considered to be in free flow traffic when its time headway was greater than 5 seconds.

Download or read book Evaluation and Summary of Studies in Speed Control Methods in Work Zones written by R. F. Benekohal and published by . This book was released on 1992 with total page 114 pages. Available in PDF, EPUB and Kindle. Book excerpt: This report summarizes and evaluates the important findings from the literature review of the studies on work zone speed control techniques. The following treatments are included in this report: 1) flagging, 2) lane width reduction, 3) law enforcement, 4) changeable message signs (CMS), 5) rumble strips, and 6) flashing beacons. The effects of the speed control treatments on speed and traffic flow are evaluated based on: A) experiences with treatment, B) effects of treatment on speed, C) effectiveness of treatment, and D) comments about treatment. A brief description of the conditions under which the treatments were applied is provided, and the speed reduction effects of each technique are discussed. A reference matrix was prepared to identify publications related to each type of speed reduction treatment used in work zones.

Download or read book Effectiveness of Speed Management Methods in Work Zones written by Henry Brown and published by . This book was released on 2022 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: "Management of speeds is a significant component of any strategy to reduce work zone crashes. The objective of this study is to investigate the effectiveness of speed management countermeasures, such as speed display trailer, speed display trailer with red and blue lights, work vehicle with red and blue lights, and active and passive law enforcement, in managing vehicle speeds in work zones. The research methodology includes a review of the existing literature, field study, simulator study, and driver survey. The field study was conducted at a work zone on I-270 in the St. Louis region. All speed countermeasures tested in the field study achieved speed reductions. Active law enforcement was the most effective speed countermeasure for both daytime and nighttime conditions. Thirteen scenarios were studied using a driving simulator. Combining a speed display trailer and active law enforcement was the most effective countermeasure for daytime conditions. Using a speed display trailer by itself was the most effective for nighttime conditions. While respondents to both the driver and post-simulator surveys generally preferred the speed display trailer, they also admitted that the presence of law enforcement would be the most effective in causing them to slow down. Overall, the results of the study indicate that any of the tested countermeasures would help reduce speeds in a work zone. In some instances, deploying multiple countermeasures at the same site was found to be the most effective speed reduction strategy"--Abstract.

Download or read book Speed Reduction Effects of Changeable Message Signs in a Construction Zone written by R. F. Benekohal and published by . This book was released on 1992 with total page 94 pages. Available in PDF, EPUB and Kindle. Book excerpt: This study evaluated the vehicular speed reduction effects of displaying speed limit and information messages on a changeable message sign (CMS) placed inside the work activity area in a work zone for a one lane closure on a rural interstate highway. It also examined the additional effects of using two CMS devices compared to one CMS. The following three experiments were conducted: (1) One CMS in advance of the work zone (Experiment 1), (2) One CMS inside the work activity area (Experiment 2), and (3) Two CMSs inside the work activity area (Experiment 3). Displaying speed limit and information messages on CMSs placed in the work activity area was effective in reducing the average speed and percentages of vehicles with excessive speeds. Comparing the results from Experiments 2 and 3 indicated that displaying the CMS messages reduced the speed of cars immediately after passing the CMS, but not at a point far from the CMS. Although trucks did not consistently reduce their speeds near the first CMS, trucks traveled at reduced speeds after passing the CMS. Cars and trucks reduced their speeds by as much as 5 and 4 mph, respectively, near the CMS. The speed reduction depended on the travel speed of the vehicles. Placing the CMS in the work activity area was more effective than putting it in advance of the work zone.

Download or read book Work Zone Speed Management written by John W. Shaw and published by . This book was released on 2015 with total page 152 pages. Available in PDF, EPUB and Kindle. Book excerpt: This synthesis documents information regarding the current state of practice for work zone speed management. The report compiles data, procedures, techniques, and technical issues related to observing and comparing work zone speeds. The speed management measures have been organized into four categories: engineering, operational, enforcement, and public education and outreach. Information included in this study was acquired through a review of the literature, two surveys of state department of transportation representatives in all states, a compilation of state agency public information campaigns, and follow-up interviews with select survey respondents from several U.S. states and one Canadian province.

Download or read book Improving Work Zone Safety Through Speed Management written by Norman M. Sommers and published by . This book was released on 2013 with total page 78 pages. Available in PDF, EPUB and Kindle. Book excerpt: Safety hazards are increased in highway work zones as the dynamics of a work zone introduce a constantly changing environment with varying levels of risk. Excessive speeding through work and maintenance zones is a common occurrence which elevates the dangers to both drivers and motorists in the work zone. Although most work zones are controlled by reduced speed limits or state law enforcement, driver adherence to these regulations and laws in very minimal, especially in work zones. Several studies have shown a correlation between speeding in work zones and traffic crashes which lead most traffic safety professionals to conclude that excessive speeding and speed variance are the contributing factors in a large percentage of traffic crashes, injuries or fatalities. The most influential factor in achieving speed compliance in the work zone is the driver's perception of heightened risk. The main objective of this study was to determine the safest and most effective countermeasure for the reduction of vehicular speeds within construction and maintenance work zones. The purpose of the simulator experiment was to determine the effectiveness of 20 countermeasures on the reduction of speed through work zones in a controlled laboratory setting. The literature review identified several past research studies utilizing speed reduction countermeasures in work zones and under normal traffic conditions. From this review, 20 countermeasures were selected for evaluation based upon discussions with ODOT personnel.The post hoc tests indicated that the presence of construction workers, presence of construction vehicles, law enforcement, speed photo enforcement and shifting lanes were most effective at reducing speeds in work zones. The least effective speed reduction countermeasures included 3 sets of 3 rumble strips, concrete barriers, other channelizing devices and changeable message signs with speed reductions less than 10 mph.

Download or read book Speed Reduction Profiles of Vehicles in a Highway Construction Zone written by and published by . This book was released on 1992 with total page 198 pages. Available in PDF, EPUB and Kindle. Book excerpt: In response to roadway geometry and traffic control devices, motorists may change their speeds within in a work zone. Speed profile data were collected for 208 vehicles who traveled a 1 .5-mile long section of a work zone, and speed reduction patterns were determined for Autos and Trucks. Four driver categories were identified based on the patterns. About 61% of the drivers reduced their speeds considerably after the first work zone speed limit signs, but nearly 15% of the drivers did not reduce their speeds until they neared the location of construction activities. About 11% of the drivers traveled at consistently high speeds and did not considerably reduce their speeds. The remaining drivers did not display a common pattern. The average speeds of Autos and Trucks were 5-18 mph and 1-12 mph, respectively, over the work zone speed limit. Vehicles decreased their speeds to the lowest level near the work space, but increased them after passing it. Even at the work space, about 65% of Autos and 47% of Trucks traveled faster than the speed limit. Autos and Trucks reduced their speeds by 3-13 mph and 3-12 mph, respectively, compared to their speeds at the beginning of the taper. The speeds at the beginning of the taper were used to group the vehicles into four speed groups. The maximum reduction in the average speed at different locations was greater with greater initial mean speeds; indicating that, on the average, the vehicles with higher initial speeds reduced their speeds more than the vehicles with lower initial speeds. However, the drivers in the higher initial speed groups kept higher speeds in the work zone than the drivers in the lower initial speed groups, even though the former group had greater speed reductions than the latter group.

Download or read book Speed Reduction Techniques for Rural High to low Speed Transitions written by Gerry John Forbes and published by Transportation Research Board. This book was released on 2011 with total page 114 pages. Available in PDF, EPUB and Kindle. Book excerpt: TRB's National Cooperative Highway Research Program (NCHRP) Synthesis 412: Speed Reduction Techniques for Rural High-to-Low Speed Transitions explores techniques for lowering traffic speeds in rural transition zones. Transition zones are those portions of high-speed roads that have lower posted speed limits as the roadway approaches a settlement.

Download or read book Evaluation of Work Zone Speed Reduction Measures written by T. H. Maze and published by . This book was released on 2000 with total page 146 pages. Available in PDF, EPUB and Kindle. Book excerpt: The Iowa Department of Transportation (DOT) has made improving work zone (WZ) safety a high priority. Managing vehicle speeds through work zones is perceived to be an important factor in achieving this goal. A number of speed reduction techniques are currently used by transportation agencies throughout the country to control speeds and reduce speed variation at work zones. The purpose of this project is to study these and other applicable work zone speed reduction strategies. Furthermore, this research explores transportation agencies' policies regarding managing speeds in long-term, short-term, and moving work zones. This report consists of three chapters. The first chapter, a literature review, examines the current speed reduction practices at work zones and provides a review of the relevant literature. The speed control strategies reviewed in this chapter range from posting regulatory and advisory speed limit signs to using the latest radar technologies to reduce speeds at work zones. The second chapter includes a short write-up for each identified speed control technique. The write-up includes a description, the results of any field tests, the benefits and the costs of the technology or technique. To learn more about other state policies regarding work zone speed reduction and management, the Center for Transportation Research and Education conducted a survey. The survey consists of six multipart questions. The third chapter provides summaries of the response to each question.

Download or read book Controlling Speeds in Highway Work Zones written by Stephen H. Richards and published by . This book was released on 1984 with total page 104 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Speed Control Through Work Zones written by and published by . This book was released on 1987 with total page 56 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Studies to Improve the Management of Regulatory Speed Limits in Texas Work Zones written by and published by . This book was released on 2008 with total page 162 pages. Available in PDF, EPUB and Kindle. Book excerpt: This report describes the methodology and results of analyses performed to (1) improve existing procedures on establishing and managing work zone speed limits, and (2) evaluate new technologies and strategies that can be used to better manage work zone speed limits. Field studies indicated that motorists reduce their speed adjacent to most of the work zone conditions currently used in Texas to justify reduced work zone speed limits; however, the amount of the speed reduction is dependent upon the normal non-work zone operating speed of the roadway. Based on the field study findings, researchers recommended a 5 mph maximum speed reduction for shoulder activity and lane encroachment conditions. A 10 mph maximum speed reduction is still warranted for lane closures and temporary diversions. Speed limit reductions should be discouraged on roadways with existing speed limits less than 65 mph for all conditions except lane closures when workers are in a closed lane unprotected by barrier and only a single travel lane remains open. Short term work zone speed limits are reduced speed limits that are posted only when work activity is present.

Download or read book Strategies for Work Zone Transportation Management Plans written by Leverson Boodlal and published by . This book was released on 2020 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: One of the ways a state department of transportation or other transportation agency can address work zone safety and other impacts is to develop and implement a Transportation Management Plan (TMP). The TRB National Cooperative Highway Research Program's NCHRP Research Report 945: Strategies for Work Zone Transportation Management Plans provides a practitioner-ready guidebook on how to select and implement strategies that improve safety and traffic operations in roadway construction work zones. Supplemental materials to the report include NCHRP Web-Only Document 276: Evaluating Strategies for Work ZoneTransportation Management Plans; fact sheets on ramp meter, reversible lane, and truck restrictions; and guidebook appendices.

Download or read book Report written by and published by . This book was released on 1964 with total page 44 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Effects of Police Presence on Speed in a Highway Work Zone written by R. F. Benekohal and published by . This book was released on 1992 with total page 84 pages. Available in PDF, EPUB and Kindle. Book excerpt: This study evaluated the effects of police presence on the speed of vehicles in a work zone and determined the "halo" effects of police presence (lasting effects when police are gone) on vehicular speeds. A marked police car circulated in a 4-mile long interstate highway work zone and actively enforced the speed limit laws. Variables such as the average speed, speed distribution, percentage of fast-moving motorists, and net speed reductions for cars and trucks were used for evaluation. The results indicated that the average speeds of the cars and trucks were 4.3-4.4, and 4.3-5.0 mph, respectively, lower when police were patrolling the work zone compared to no-police patrol condition. The percentage of fast-moving cars and trucks before the work space decreased by 14% and 32%, respectively, when police were in the work zone. These speed reductions indicate that the police presence was effective in decreasing the speed of vehicles in the work zone. The police presence had halo effects on trucks but not on cars. Trucks traveled at reduced speed when police were present in the work zone and this trend of traveling at the reduced speed continued for a time period at least one hour after the police departed from the work zone. However, cars traveled 2. 4-3. o mph faster and the percentage of fast-moving cars in the work zone increased after the police left the area.

Download or read book Evaluation of Work Zone Speed Limit Signs with Strobe Lights written by R. F. Benekohal and published by . This book was released on 1992 with total page 100 pages. Available in PDF, EPUB and Kindle. Book excerpt: The construction zone speed limit sign used in Illinois consists of a regulatory 45 mph speed limit sign augmented with two small strobe lights and two orange colored plates. When the lights are flashing the speed limit is 45 mph. This report contains the findings from evaluation of the effectiveness of the flashing lights in reducing speeds in a rural interstate construction zone. The speed reduction effects on cars and trucks were determined at two locations within the work zone. The results indicated that the average speed of cars was reduced by 1.9-7.1 mph and that of trucks by 1.3-6.0 mph when the strobe lights were flashing. In general, the speed reduction effects were more pronounced on the cars than on the trucks, and at a location past the work space than before it. The reductions at the location past the work space were 2-3 times more than the reductions at the location before the work space. Cars reduced their speeds, on the average, by 1.9 to 4.9 mph before and by 5.9 to 7.1 mph after the work space. Similarly, the speed reduction for trucks was 1.3-2.9 mph before and 3.3-6.0 after the work space. In general, the percentages of vehicles with excessive speeds in the work zone decreased when the lights were flashing.

Download or read book Effective Speed Reduction in Work Zones written by Stirling P. Stackhouse and published by . This book was released on 1998 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: