Download or read book Room and Elevated Temperature Sliding Wear Behavior of Cold Sprayed Ni WC Composite Coatings written by Tyler B. Torgerson and published by . This book was released on 2018 with total page 50 pages. Available in PDF, EPUB and Kindle. Book excerpt: The tribological properties of cold sprayed Ni-WC metal matrix composite (MMC) coatings were investigated under dry sliding conditions from room temperature (RT) up to 400°C, and during thermal cycling to explore their temperature adaptive friction and wear behavior. Characterization of worn surfaces was conducted using scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), and Raman spectroscopy to determine the chemical and microstructural evolution during friction testing. Data provided insights into tribo-oxide formation mechanisms controlling friction and wear. It was determined that the steady-state coefficient of friction (CoF) decreased from 0.41 at RT to 0.32 at 400 ̊C, while the wear rate increased from 0.5×10-4 mm3/N·m at RT to 3.7×10-4 mm3/N·m at 400 ̊C. The friction reduction is attributed primarily to the tribochemical formation of lubricious NiO on both the wear track and transfer film adhered to the counterface. The increase in wear is attributed to a combination of thermal softening of the coating and a change in the wear mechanism from adhesive to more abrasive. In addition, the coating exhibited low friction behavior during thermal cycling by restoring the lubricious NiO phase inside the wear track at high temperature intervals. Therefore, cold sprayed Ni-WC coatings are potential candidates for elevated temperature and thermally self-adaptive sliding wear applications.
Download or read book Cold Spray Deposition of Ni WC Composite Coatings and Their Sliding and Erosive Wear Behaviour written by Sima Ahmad Ali Dokht and published by . This book was released on 2018 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Thermal Spray Coatings written by Lalit Thakur and published by CRC Press. This book was released on 2021-11-03 with total page 367 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book provides the latest information about the research being conducted and established solutions available in the field of thermal spray coatings for various engineering applications. The readers of this book will be mainly the graduates, engineers and researchers who are pursuing their carrier in the field of thermal spraying. This book will cover the studies and research works of reputed scientists and engineers who have developed thermal spray coatings for thermal protection, bio-implants, renewal energy, wear and corrosion in hydraulic turbines and jet engines, hydrophobic surfaces etc. Hence, the book serves as a valuable resource of latest advancement in thermal spray technology and consolidated references for aspirants and professionals of surface engineering community. The book covers following topics for different industrial applications: Introduction: Historical developments, Science and Engineering aspects of thermal spray coating technology and different thermal spray coatings techniques and its comparison with other fabrication processes. Recent advancements and applications of thermal spray coatings Cold spray technology for additive manufacturing. High-temperature corrosion and erosion resistant coatings and thermal barrier coatings for power plants, automotive sector, and jet engines. Erosion and corrosion-resistant coatings for hydro-power plants, offshore, chemical and oil industries. Bio-coatings for human body implants. Thermal spray coating for super-hydrophobic surface. 3. Case study of boiler tubes failure and prevention by thermal spray coatings.
Download or read book Residual Stresses in Composite Materials written by Mahmood M. Shokrieh and published by Woodhead Publishing. This book was released on 2021-06-22 with total page 506 pages. Available in PDF, EPUB and Kindle. Book excerpt: The residual stress is a common phenomenon in composite materials. They can either add to or significantly reduce material strength. Because of the increasing demand for high-strength, lightweight materials such as composites and their wide range of applications; it is critical that the residual stresses of composite materials are understood and measured correctly.The first edition of this book consists of thirteen chapters divided into two parts. The first part reviews destructive and non-destructive testing (NDT) techniques for measuring residual stresses. There are also additional chapters on using mathematical (analytical and numerical) methods for the calculation of residual stresses in composite materials. These include the simulated hole drilling method, the slitting/crack compliance method, measuring residual stresses in homogeneous and composite glass materials using photoelastic techniques, and modeling residual stresses in composite materials. The second part of the book discusses measuring residual stresses in different types of composites including polymer and metal matrix composites. The addition of nanoparticles to the matrix of polymeric composites as a new technique for the reduction of residual stresses is also discussed.In the Second Edition of this book, each of the original chapters of the first edition has been fully updated, taking into account the latest research and new developments. There are also five new chapters on the theoretical and experimental studies of residual stresses in the composite integrated circuits; residual stresses in additive manufacturing of polymers and polymer matrix composites; residual stresses in metal matrix composites fabricated by additive manufacturing; the eigenstrain based method for the incremental hole-drilling technique; and the estimation of residual stresses in polymer matrix composites using the digital image correlation technique.Residual Stresses in Composite Materials, Second Edition, provides a unique and comprehensive overview of this important topic and is an invaluable reference text for both academics and professionals working in the mechanical engineering, civil engineering, aerospace, automotive, marine, and sporting industries. - Presents the latest developments on theoretical and experimental studies of residual stresses in composites - Reviews destructive and non-destructive testing (NDT) techniques for measuring residual stresses - Discusses residual stresses in the polymer matrix, metal matrix, and ceramic matrix composites - Considers the addition of nanoparticles to the matrix as a new technique for reduction of residual stresses in polymeric composites - Introduces the latest advancements of research on the residual stresses in additive-manufactured polymer and metal matrix composites
Download or read book Cold Spray Coatings written by Pasquale Cavaliere and published by Springer. This book was released on 2017-11-08 with total page 566 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book combines the contributions of experts in the field to describe the behavior of various materials, micromechanisms involved during processing, and the optimization of cold-spray technology. It spans production, characterization, and applications including wear resistance, fatigue, life improvement, thermal barriers, crack repair, and biological applications. Cold spray is an innovative coating technology based on the kinetic energy gained by particles sprayed at very high pressures. While the technique was developed in the 1990s, industrial and scientific interest in this technology has grown vastly in the last ten years. Recently, many interesting applications have been associated with cold-sprayed coatings, including wear resistance, fatigue life improvement, thermal barriers, biological applications, and crack repair. However, many fundamental aspects require clarification and description.
Download or read book Handbook of Thermal Spray Technology written by Joseph R. Davis and published by ASM International. This book was released on 2004-01-01 with total page 344 pages. Available in PDF, EPUB and Kindle. Book excerpt: This reference covers principles, processes, types of coatings, applications, performance, and testing and analysis of thermal spray technology. It will serve as an introduction and guide for those new to thermal spray, and as a reference for specifiers and users of thermal spray coatings and thermal spray experts. Coverage encompasses basics of th
Download or read book Thermal Spray Fundamentals written by Pierre L. Fauchais and published by Springer Science & Business Media. This book was released on 2014-01-24 with total page 1587 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book provides readers with the fundamentals necessary for understanding thermal spray technology. Coverage includes in-depth discussions of various thermal spray processes, feedstock materials, particle-jet interactions, and associated yet very critical topics: diagnostics, current and emerging applications, surface science, and pre and post-treatment. This book will serve as an invaluable resource as a textbook for graduate courses in the field and as an exhaustive reference for professionals involved in thermal spray technology.
Download or read book Self Lubricating Composites written by Pradeep L. Menezes and published by Springer Nature. This book was released on 2022-01-03 with total page 305 pages. Available in PDF, EPUB and Kindle. Book excerpt: In most tribological applications, liquid or grease based lubricants are used to facilitate the relative motion of solid bodies to minimize friction and wear between interacting surfaces. The challenges for liquid lubricants arise in extreme environmental conditions, such as very high or low temperatures, vacuum, radiation, and extreme contact pressure. At these conditions, solid lubricants may be the alternative choice which can help to decrease friction and wear without incorporating liquid lubricants. Challenges with solid lubricants are to maintain a continuous supply of solid lubricants on the contact surfaces to act as lubricous layer between two sliding surfaces. Such a continuous supply is more easily maintained in the case of liquid lubricants when compared to solid lubricants. The most innovative development to ensure a continuous supply of solid lubricant to the contact surface during sliding is to introduce solid lubricant as reinforcement into the matrix of one of the sliding components. Composite materials are engineered or naturally occurring materials which contain two or more distinct constituents with significantly different chemical, physical and mechanical properties. Composites consist of reinforcement and matrix (metal, polymer and ceramics). Among various reinforcements, recent emerging material, solid lubricant, is found to have many favorable attributes such as good lubrication property. Self‐lubrication is the ability of a material to provide lubrication to the contact surface to decrease friction and wear rate in the absence of an external lubricant by transferring embedded solid lubricants in the composite to the interface. Self-lubricating composites (SLCs) are an important category of engineering materials that are increasingly replacing a number of conventional materials in the automotive, aerospace, and marine industries due to superior tribological properties. In SLCs, solid lubricant materials, including carbonous materials, molybdenum disulfide (MoS2), and hexagonal boron nitride (h-BN) are embedded into the matrices as reinforcements to manufacture a novel material with attractive self-lubricating properties. Several studies have been investigated the tribological properties of self-lubricating materials. This book fills that gap to have a reference book about self-lubricating materials and their properties to help scientists, engineers, and industries. This book discusses mechanisms of self-lubricating materials, self-lubricating properties and the applications for industries. The chapters will be written by authoritative expertise in the field. Additionally, this book will demonstrate fundamental study and most advanced innovations in self-lubricating materials as regards to friction and wear. The chapters also include tribological properties of composites and coatings and some practical applications of self-lubricating materials.
Download or read book Modern Cold Spray written by Julio Villafuerte and published by Springer. This book was released on 2015-08-24 with total page 435 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book focuses on the current state of the art of the novel cold spray process. Cold spray is a solid state metal consolidation process, which allows engineers to tailor surface and shape properties by optimizing process parameters, powder characteristics and substrate conditions for a wide variety of applications that are difficult or impossible by other techniques. Readers will benefit from this book's coverage of the commercial evolution of cold spray since the 1980's and will gain a practical understanding of what the technology has to offer.
Download or read book Sliding Wear Behavior of Tungsten Carbide Thermal Spray Coatings Standard Finish Versus Superfinish written by David L. Redman and published by . This book was released on 2001 with total page 244 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Handbook of Research on Tribology in Coatings and Surface Treatment written by Pakseresht, Amirhossein and published by IGI Global. This book was released on 2022-03-25 with total page 470 pages. Available in PDF, EPUB and Kindle. Book excerpt: Advances are continuously being made in applying the coatings and surface treatments by different techniques to reduce the damages from tribology. Engineers need more detailed information to compare the capability of each coating process in wear resistant and lubrication applications. It is also important to focus on the concepts of tribology in various applications such as the manufacturing process, bio implants, machine elements, and corrosive environments. The need for a comprehensive resource addressing these findings in order to improve wear resistance is unavoidable. The Handbook of Research on Tribology in Coatings and Surface Treatment evaluates the latest advances the fabrication of wear-resistant and lubricant coatings by different techniques and investigates wear-resistant coatings and surface treatments in various applications such as the automobile industry. Covering a wide range of topics such as lubricant coatings and wearable electronic devices, it is ideal for engineers, industry professionals, researchers, academicians, scholars, practitioners, instructors, and students.
Download or read book Cold Spray Technology written by Anatolii Papyrin and published by Elsevier. This book was released on 2006-10-04 with total page 341 pages. Available in PDF, EPUB and Kindle. Book excerpt: The topic of this book is Cold Spray technology. Cold Spray is a process of applying coatings by exposing a metallic or dielectric substrate to a high velocity (300 to 1200 m/s) jet of small (1 to 50 μm) particles accelerated by a supersonic jet of compressed gas. This process is based on the selection of the combination of particle temperature, velocity, and size that allows spraying at the lowest temperature possible. In the Cold Spray process, powder particles are accelerated by the supersonic gas jet at a temperature that is always lower than the melting point of the material, resulting in coating formation from particles in the solid state. As a consequence, the deleterious effects of high-temperature oxidation, evaporation, melting, crystallization, residual stresses, gas release, and other common problems for traditional thermal spray methods are minimized or eliminated. This book is the first of its kind on the Cold Spray process. Cold Spray Technology covers a wide spectrum of various aspects of the Cold Spray technology, including gas-dynamics, physics of interaction of high-speed solid particles with a substrate as well as equipment, technologies, and applications. Cold Spray Technology includes the results of more than 20 years of original studies (1984-2005) conducted at the Institute of Theoretical and Applied Mechanics of the Siberian Division of the Russian Academy of Science, as well as the results of studies conducted at most of the research centres around the world. The authors' goal is threefold. The first goal is to explain basic principles and advantages of the Cold Spray process. The second goal is, to give practical information on technologies and equipment. The third goal is to present the current state of research and development in this field over the world. The book provides coverage and data that will be of interest for users of Cold Spray technology as well as for other coating experts. At the present time the Cold Spray method is recognized by world leading scientists and specialists. A wide spectrum of research is being conducted at many research centres and companies in many countries. New approach to spray coatings Results are exceptionally pure coatings Low spray temperature without degradation of powder and substrate materials High productivity, high deposition efficiency High operational safety because of absence of high temperature gas jets, radiation and explosive gases Excellent thermal and electrical conductivity Wide spectrum of applications because of important advantages of the process
Download or read book Protection against Erosive Wear using Thermal Sprayed Cermet written by Carlos P. Bergmann and published by Springer Science & Business Media. This book was released on 2011-07-02 with total page 89 pages. Available in PDF, EPUB and Kindle. Book excerpt: Erosive wear is characterized by successive loss of material from the surface due to the continuous impact of solid particles. This type of wear affects numerous industries, such as power generation, mining, and the pneumatic transportation of solids. The worst case scenario normally occurs where there is a combination of both erosion and oxidation, especially at high temperatures. In order to minimize damage caused by erosive wear, many authors propose the use of better bulk materials or surface coatings, and generally cermets are suggested. Various researchers have conducted experiments to study the wear mechanisms occurring in this kind of materials, but most of these experiments do not lead to similar results; in fact, there is no accordance among the authors, and moreover, some wear variables are ignored. In this book, studies undertaken in this field by several investigators have been discussed extensively. At the end of it, table reviews are suggested to summarize the most important mechanisms of the erosive wear in bulk and coating cermets.
Download or read book High Pressure Cold Spray written by C. M. Kay and published by . This book was released on 2016-06 with total page 324 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book is a highly practical and useful ""go-to"" resource that presents an in-depth look at the high pressure cold spray process and describes applications in various industries. Cold spray continues to be the fastest developing spray technology over the last decade, and a significant number of scientists, engineers, and technologists are joining the cold spray community around the globe. The technology is relatively young and work is being simultaneously pursued in universities, research centers, and in many high tech industries. As this novel technology spreads quickly into many new application areas, there is a large need for an authoritative source of information. This new book addresses this need and will be indispensable to universities, libraries, and those involved in thermal spray. It presents baseline information on design and modeling, materials science of engineered coatings, and specific applications in various high tech industries, and is also a hands-on resource for cold spray operators.
Download or read book Sliding Wear Behavior of Tungsten Carbide WC Thermal Spray Coatings for Replacement of Chromium Electroplate in Aircraft Applications written by Annie Cyrilla Savarimuthu and published by . This book was released on 2000 with total page 396 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book The Cold Spray Materials Deposition Process written by and published by Elsevier. This book was released on 2007-09-21 with total page 377 pages. Available in PDF, EPUB and Kindle. Book excerpt: The cold spray process produces dense, low oxide coatings which can be used in such diverse applications as corrosion control and metals repair. It has emerged as an important alternative to thermal spray coating techniques in certain areas. This pioneering book reviews both the fundamentals of the process and how it can best be applied in practice. The first part of the book discusses the development of the process together with its advantages and disadvantages in comparison with thermal spray coating techniques. Part two reviews key process parameters such as powders, nozzle design, particle temperature and velocity, and particle/substrate interaction. It also describes portable and stationary cold spray systems. The final part of the book discusses how the cold spray process can be applied in such areas as improved wear, corrosion protection, electromagnetic interference shielding and repair of damaged components. The cold spray materials deposition process is a standard reference on this important process and its industrial applications. Examines the fundamentals of the cold spraying process Assesses how the technique can best be applied in practice Describes portable and stationary cold spray systems
Download or read book The Science and Engineering of Thermal Spray Coatings written by Lech Pawlowski and published by John Wiley & Sons. This book was released on 2008-04-30 with total page 656 pages. Available in PDF, EPUB and Kindle. Book excerpt: This extensively updated and revised version builds on the success of the first edition featuring new discoveries in powder technology, spraying techniques, new coatings applications and testing techniques for coatings -- Many new spray techniques are considered that did not exist when the first edition was published! The book begins with coverage of materials used, pre-spray treatment, and the techniques used. It then leads into the physics and chemistry of spraying and discusses coatings build-up. Characterization methods and the properties of the applied coatings are presented, and the book concludes with a lengthy chapters on thermal spray applications covers such areas as the aeronautics and space, automobiles, ceramics, chemicals, civil engineering, decorative coatings, electronics, energy generation and transport, iron and steel, medicine, mining and the nuclear industries.
