Download or read book New Methods for Engineering Site Characterization Using Reflection and Surface Wave Seismic Surveys written by Susit Chaiprakaikeow and published by . This book was released on 2012 with total page 149 pages. Available in PDF, EPUB and Kindle. Book excerpt: PUBLIC ABSTRACT: This study presents two new seismic testing methods for engineering application, a new shallow seismic reflection method and Time Filtered Analysis of Surface Waves (TFASW). Both methods are described in this dissertation. The new shallow seismic reflection was developed to measure reflections at a single point using 2-4 receivers, assuming homogeneous, horizontal layering. Two problems commonly encountered in reflection testing are dealt with in this new method. These problems are: phase shifts between the wave source and ground motion; and, loss of high frequency energy. Using approaches to mitigate these problems significantly improved the shape of measured waveforms. However, none of the sites investigated yielded strong enough reflectors to fully characterize the sites. TFASW is a new surface (Rayleigh) wave method to determine the shear wave velocity profile at soil and rock sites. The method is an improvement over other surface wave seismic methods because digital filters with optimized bandwidths are used to characterize the surface wave dispersion. Successful applications of the TFASW method are shown at three sites.
Download or read book Surface Wave Methods for Near Surface Site Characterization written by Sebastiano Foti and published by CRC Press. This book was released on 2014-08-21 with total page 492 pages. Available in PDF, EPUB and Kindle. Book excerpt: Develop a Greater Understanding of How and Why Surface Wave Testing Works Using examples and case studies directly drawn from the authors’ experience, Surface Wave Methods for Near-Surface Site Characterization addresses both the experimental and theoretical aspects of surface wave propagation in both forward and inverse modeling. This book accents the key facets associated with surface wave testing for near-surface site characterization. It clearly outlines the basic principles, the theoretical framework and the practical implementation of surface wave analysis. In addition, it also describes in detail the equipment and measuring devices, acquisition techniques, signal processing, forward and inverse modeling theories, and testing protocols that form the basis of modern surface wave techniques. Review Examples of Typical Applications for This Geophysical Technique Divided into eight chapters, the book explains surface wave testing principles from data measurement to interpretation. It effectively integrates several examples and case studies illustrating how different ground conditions and geological settings may influence the interpretation of data measurements. The authors accurately describe each phase of testing in addition to the guidelines for correctly performing and interpreting results. They present variants of the test within a consistent framework to facilitate comparisons, and include an in-depth discussion of the uncertainties arising at each stage of surface wave testing. Provides a comprehensive and in-depth treatment of all the steps involved in surface wave testing Discusses surface wave methods and their applications in various geotechnical conditions and geological settings Explains how surface wave measurements can be used to estimate both stiffness and dissipative properties of the ground Addresses the issue of uncertainty, which is often an overlooked problem in surface wave testing Includes examples with comparative analysis using different processing techniques and inversion algorithms Outlines advanced applications of surface wave testing such as joint inversion, underwater investigation, and Love wave analysis Written for geotechnical engineers, engineering seismologists, geophysicists, and researchers, Surface Wave Methods for Near-Surface Site Characterization offers practical guidance, and presents a thorough understanding of the basic concepts.
Download or read book Surface Wave Methods for Near Surface Site Characterization written by Sebastiano Foti and published by CRC Press. This book was released on 2014-08-21 with total page 482 pages. Available in PDF, EPUB and Kindle. Book excerpt: Develop a Greater Understanding of How and Why Surface Wave Testing WorksUsing examples and case studies directly drawn from the authors' experience, Surface Wave Methods for Near-Surface Site Characterization addresses both the experimental and theoretical aspects of surface wave propagation in both forward and inverse modeling. This book accents
Download or read book Seeing into the Earth written by National Research Council and published by National Academies Press. This book was released on 2000-04-26 with total page 155 pages. Available in PDF, EPUB and Kindle. Book excerpt: Just below our feet is an environment that supports our infrastructure, yields water, provides for agriculture, and receives our waste. Our capacity to describe, or characterize, this environment is crucial to the solution of many resource, environmental, and engineering problems. And just as medical imaging technologies have reduced the need for exploratory surgeries, a variety of technologies hold the promise for rapid, relatively inexpensive noninvasive characterization of the Earth's subsurface. Seeing into the Earth examines why noninvasive characterization is important and how improved methods can be developed and disseminated. Looking at the issues from both the commercial and public perspectives, the volume makes recommendations for linking characterization and cost savings, closing the gap between the state of science and the state of the practice, and helping practitioners make the best use of the best methods. The book provides background on: The role of noninvasive subsurface characterization in contaminant cleanup, resource management, civil engineering, and other areas. The physical, chemical, biological, and geological properties that are characterized. Methods of characterization and prospects for technological improvement. Certain to be important for earth scientists and engineers alike, this book is also accessible to interested lay readers.
Download or read book Geophysical Characterization of Sites written by Richard D. Woods and published by Science Publishers. This book was released on 1994 with total page 160 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Advancements in 1D and 2D Near surface Seismic Site Characterization Using Surface Waves and Full Waveform Inversion written by Michael Benjamin Schutt Yust and published by . This book was released on 2022 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: Seismic site characterization is a critical part of understanding earthquake hazards in geotechnical engineering. This is often accomplished through various invasive and non-invasive methods for measuring shear-wave velocity (Vs) in-situ, as it is directly related to small-strain shear modulus. For civil engineering applications, the seismic conditions of the near surface (top 30 m) are of particular interest. Surface wave testing has become the tool of choice for many engineers due to its flexibility, efficiency, and ability to characterize a wide variety of subsurface conditions. Surface wave testing is also particularly well suited to near-surface imaging due to the prevalence of surface waves within the elastic wavefield at shallow depths. Surface wave testing, however, is not without limitations. Inversion of surface wave dispersion data is ill-posed and non-unique, meaning that when it is performed rigorously with full consideration of epistemic uncertainty, a potentially large number of reasonable and different 1D Vs profiles are produced. This presents a challenge of evaluating which profiles should be used for further analysis or design. Additionally, engineers often desire information about the lateral variability of seismic parameters in the subsurface, but the inherently 1D nature of the processing and inversion techniques used in surface wave testing make acquiring this information challenging. Evaluation of lateral variability is generally accomplished through multiple individual 1D surface wave analyses across the site, providing only pseudo-2D information. This also introduces a new challenge: how to collect the large amount of experimental data required for multiple analyses as the efficiency of traditional surface wave acquisition is limited by the need to physically move geophone arrays with limited numbers of sensors. This dissertation discusses these challenges and presents potential solutions through the application of the DeltaVs method, distributed acoustic sensing, and full waveform inversion
Download or read book Engineering Seismology with Applications to Geotechnical Engineering written by Öz Yilmaz and published by SEG Books. This book was released on 2015-05-20 with total page 966 pages. Available in PDF, EPUB and Kindle. Book excerpt: The scope of engineering seismology includes geotechnical site investigations for buildings and engineering infrastructures, such as dams, levees, bridges, and tunnels, landslide and active-fault investigations, seismic microzonation, and geophysical investigations of historic buildings. These projects require multidisciplinary participation by the geologist, geophysicist, and geotechnical and earthquake engineers. A key objective of this book (SEG Investigations in Geophysics Series No. 17) by Öz Yilmaz is to encourage the specialists from these disciplines to apply the seismic method to solve the many challenging engineering problems they face. The broader scope of engineering seismology also includes exploration of earth resources, including groundwater exploration, coal and mineral exploration, and geothermal exploration. While focusing on the application of the seismic method to geotechnical site investigations, this book includes many case studies in all of the applications of engineering seismology.
Download or read book Static Corrections for Seismic Reflection Surveys written by Michael J. G. Cox and published by SEG Books. This book was released on 1999 with total page 546 pages. Available in PDF, EPUB and Kindle. Book excerpt: This reference manual is designed to enable more geophysicists to appreciate static corrections, especially their limitations, their relationship with near-surface geology, and their impact on the quality of final interpreted sections. The book is addressed to those involved in data acquisition (datum static corrections), data processing (datum static and residual static corrections), and interpretation (the impact that unresolved static corrections, especially the long-wavelength or low-spatial-frequency component, have on the interpretation of the final section). Simple explanations of the underlying principles are included in an attempt to remove some of the mystique of static corrections. The principles involved are illustrated with simple models; these are supplemented with many data examples. This book details differences in approaches that must be considered among 2D, 3D, and crooked-line recordings as well as between P-wave and S-wave surveys. Static corrections are shown to be a simplified yet practical approach to modeling the effects of the near surface where a more correct wavefield or raypath-modeled method may not be efficiently undertaken. Chapters cover near-surface topography and geology; computation of datum static corrections; uphole surveys; refraction surveys; static corrections-limitations and effect on seismic data processes; residual static corrections; and interpretation aspects. An extensive index and a large list of references are included.
Download or read book Geotechnical and Geophysical Site Characterization 4 written by Roberto Quental Coutinho and published by CRC Press. This book was released on 2012-09-06 with total page 1888 pages. Available in PDF, EPUB and Kindle. Book excerpt: Site characterization is a fundamental step towards the proper design, construction and long term performance of all types of geotechnical projects, ranging from foundation, excavation, earth dams, embankments, seismic hazards, environmental issues, tunnels, near and offshore structures. Geotechnical and Geophysical Site Characterization 4 provides practical applications of novel and innovative technologies in geotechnical and geophysical engineering, and is of interest to academics, engineers and professionals involved in Geotechnical Engineering.
Download or read book Geotechnical and Geophysical Site Characterization written by António Viana da Fonseca and published by . This book was released on 2004 with total page 1082 pages. Available in PDF, EPUB and Kindle. Book excerpt: "Soils and rocks are complex natural geomaterials that exhibit a wide range in strength, stiffness, state of stress, structure, and flow characteristics. Geotechnical & Geophysical Site Characterization provides eleven keynote state-of-the-art papers, including the Mitchell Lecture. A total selection of 219 technical papers and theme reports address methods of site exploration related to ground exploration for civil engineering and construction works. These two volumes represent a collection of experience & knowledge regarding various methods of in-situ testing, geophysical techniques, innovative devices, improved interpretation algorithms, and statistical treatment of field data for the characterization of soils, rocks, and other geomaterials. The papers represent the written records and documented efforts from international experts from industry, academe, and government who participated in the Second International Conference on Site Characterization held in Porto, Portugal on September 20-22, 2004. Topics include the utilization of rotary drilling, sampling, and coring techniques. Of particular interest is the variety of in-situ tests, including standard penetration, cone penetration, flat dilatometer, pressuremeter, vane shear, piezocone, dynamic probes, and specialized tools, as well as geophysical approaches: resistivity surveys, surface waves, crosshole, downhole, electromagnetic conductivity, and ground penetrating radar. A careful and proper site evaluation is required in the analysis and design of new structures, construction monitoring, and forensic studies that require remediation. Many of the contributions relate to case studies of projects that involve shallow foundations, drilled shafts, pilings, slope stability, excavations, earth dams, tunnels, and mining. Several papers discuss a combined approach using multiple methods and/or complementary set of geotechnical & geophysical tests to ascertain the characteristics of the ground."--back cover.
Download or read book Seismic Data Analysis written by Özdoğan Yilmaz and published by SEG Books. This book was released on 2001 with total page 2065 pages. Available in PDF, EPUB and Kindle. Book excerpt: Expanding the author's original work on processing to include inversion and interpretation, and including developments in all aspects of conventional processing, this two-volume set is a comprehensive and complete coverage of the modern trends in the seismic industry - from time to depth, from 3D to 4D, from 4D to 4C, and from isotropy to anisotropy.
Download or read book Hydrogeophysics written by Yorum Rubin and published by Springer Science & Business Media. This book was released on 2006-05-06 with total page 518 pages. Available in PDF, EPUB and Kindle. Book excerpt: This ground-breaking work is the first to cover the fundamentals of hydrogeophysics from both the hydrogeological and geophysical perspectives. Authored by leading experts and expert groups, the book starts out by explaining the fundamentals of hydrological characterization, with focus on hydrological data acquisition and measurement analysis as well as geostatistical approaches. The fundamentals of geophysical characterization are then at length, including the geophysical techniques that are often used for hydrogeological characterization. Unlike other books, the geophysical methods and petrophysical discussions presented here emphasize the theory, assumptions, approaches, and interpretations that are particularly important for hydrogeological applications. A series of hydrogeophysical case studies illustrate hydrogeophysical approaches for mapping hydrological units, estimation of hydrogeological parameters, and monitoring of hydrogeological processes. Finally, the book concludes with hydrogeophysical frontiers, i.e. on emerging technologies and stochastic hydrogeophysical inversion approaches.
Download or read book Seismic Site Characterization Techniques Applied to the NATO RSG 11 Test Site in M nster Nord Federal Republic of Germany written by Donald G. Albert and published by . This book was released on 1982 with total page 48 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Seismic Imaging a Practical Approach written by Jean-Luc Mari and published by . This book was released on 2021 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: In the geophysics of oil exploration and reservoir studies, the surface seismic method is the most commonly used method to obtain a subsurface model in 2 or 3 dimensions. This method plays an increasingly important role in soil investigations for geotechnical, hydrogeological and site characterization studies regarding seismic hazard issues. The goal of this book is to provide a practical guide, using examples from the field, to the application of seismic methods to surface imaging. After reviewing the current state of knowledge in seismic wave propagation, refraction and reflection seismic methods, the book aims to describe how seismic tomography and fullwave form inversion methods can be used to obtain seismic images of the subsurface. Through various synthetic and field examples, the book highlights the benefit of combining different sets of data: refracted waves with reflected waves, and body waves with surface waves. With field data targeting shallow structures, it shows how more accurate geophysical models can be obtained by using the proposed hybrid methods. Finally, it shows how the integration of seismic data (3D survey and VSP), logging data (acoustic logging) and core measurements, combined with a succession of specific and advanced processing techniques, enables the development of a 3D high resolution geological model in depth. In addition to these examples, the authors provide readers with guidelines to carry out these operations, in terms of acquisition, as well as processing and interpretation. In each chapter, the reader will find theoretical concepts, practical rules and, above all, actual application examples. For this reason, the book can be used as a text to accompany course lectures or continuing education seminars. This book aims to promote the exchange of information among geologists, geophysicists, and engineers in geotechnical fields.
Download or read book Engineering Seismology written by Özdoğan Yilmaz and published by . This book was released on 2015 with total page 954 pages. Available in PDF, EPUB and Kindle. Book excerpt: The scope of engineering seismology includes geotechnical site investigations for buildings and engineering infrastructures, such as dams, levees, bridges, and tunnels, landslide and active-fault investigations, seismic microzonation, and geophysical investigations of historic buildings. These projects require multidisciplinary participation by the geologist, geophysicist, and geotechnical and earthquake engineers. A key objective of this book (SEG Investigations in Geophysics Series No. 17) by Öz Yilmaz is to encourage the specialists from these disciplines to apply the seismic method to solve the many challenging engineering problems they face. The broader scope of engineering seismology also includes exploration of earth resources, including groundwater exploration, coal and mineral exploration, and geothermal exploration. While focusing on the application of the seismic method to geotechnical site investigations, this book includes many case studies in all of the applications of engineering seismology.
Download or read book Seismic Waves written by Masaki Kanao and published by BoD – Books on Demand. This book was released on 2012-01-25 with total page 340 pages. Available in PDF, EPUB and Kindle. Book excerpt: The importance of seismic wave research lies not only in our ability to understand and predict earthquakes and tsunamis, it also reveals information on the Earth's composition and features in much the same way as it led to the discovery of Mohorovicic's discontinuity. As our theoretical understanding of the physics behind seismic waves has grown, physical and numerical modeling have greatly advanced and now augment applied seismology for better prediction and engineering practices. This has led to some novel applications such as using artificially-induced shocks for exploration of the Earth's subsurface and seismic stimulation for increasing the productivity of oil wells. This book demonstrates the latest techniques and advances in seismic wave analysis from theoretical approach, data acquisition and interpretation, to analyses and numerical simulations, as well as research applications. A review process was conducted in cooperation with sincere support by Drs. Hiroshi Takenaka, Yoshio Murai, Jun Matsushima, and Genti Toyokuni.
Download or read book Geotechnical Site Characterization Using Multi channel Analysis of Rayleigh and Love Waves written by James David Lane and published by . This book was released on 2009 with total page 106 pages. Available in PDF, EPUB and Kindle. Book excerpt: The Multi-Channel Analysis of Surface Waves (MASW) is a technique in which surface waves can be analyzed to determine soil shear wave velocity profiles with depth. The shear wave velocity of soil can be used to calculate the shear modulus, which is an important geotechnical engineering parameter. Site surveys were conducted and analyzed located at a location on the flood plain of the Tennessee River. The flood plain consists of a thin layer of soil above rigid (Knox Dolomite) bedrock and exhibited strong stratification. Three different aspects of MASW data acquisition and analysis are presented in the study. The first aspect is the response correction of the classical horizontal and vertical component geophone and its effects on surface wave dispersion; the second aspect is the effect of Rayleigh wave MASW data acquisition, analysis, and modeling as influenced by Rayleigh wave guides; the third aspect is the use of MASW and Love wave data acquisition, analysis, and modeling. MASW is performed using a seismic source and geophones (velocity sensor) without correcting the amplitude and phase errors induced by the equivalent single degree of freedom response function representing the mechanical response of a given velocity sensor. Geophones were experimentally tested in the laboratory to determine their natural frequency, damping ratio, and transduction constants. The results from these tests were mathematically corrected for their mechanical response and compared to uncorrected and corrected field data. Several seismic sources and various sourceoffset distances were evaluated to determine their effects on Rayleigh wave dispersion. Rayleigh waves, guided in a layer, were interpreted to have a profound influence on the Rayleigh wave dispersion data obtained using different seismic sources and source-offset distances. Results from Love wave data analysis produced superior dispersion data in comparison to the dispersion data obtained from Rayleigh wave data, making interpretation much more certain.
