Download or read book Microstructure and Tensile Properties of BN SiC Coated Hi Nicalon and Sylramic SiC Fiber Preforms written by and published by . This book was released on 2001 with total page 18 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Microstructure and Tensile Properties of BN SiC Coated Hi Nicalon and Sylramic SiC Fiber Preforms Revised written by National Aeronautics and Space Administration (NASA) and published by Createspace Independent Publishing Platform. This book was released on 2018-06-19 with total page 30 pages. Available in PDF, EPUB and Kindle. Book excerpt: Batch to batch and within batch variations, and the influence of fiber architecture on room temperature physical and tensile properties of BN/SiC coated Hi-Nicalon and Sylramic SiC fiber preform specimens were determined. The three fiber architectures studied were plain weave (PW), 5-harness satin (5HS), and 8-harness satin (8HS). Results indicate that the physical properties vary up to 10 percent within a batch, and up to 20 percent between batches of preforms. Load-reload (Hysteresis) and acoustic emission methods were used to analyze damage accumulation occurring during tensile loading. Early acoustic emission activity, before observable hysteretic behavior, indicates that the damage starts with the formation of nonbridged tunnel cracks. These cracks then propagate and intersect the load bearing "0 deg" fibers giving rise to hysteretic behavior. For the Hi-Nicalon preform specimens, the onset of "0 deg" bundle cracking stress and strain appeared to be independent of the fiber architecture. Also, the "0 deg" fiber bundle cracking strain remained nearly the same for the preform specimens of both fiber types. TEM analysis indicates that the CVI BN interface coating is mostly amorphous and contains carbon and oxygen impurities, and the CVI SiC coating is crystalline. No reaction exists between the CVI BN and SiC coating. Bhatt, Ramakrishna T. and Chen, Yuan L. and Morscher, Gregory N. Glenn Research Center NASA/TM-2001-210695/REV1, E-12626-1/REV1, NAS 1.15:210695/REV1
Download or read book Microstructure and Tensile Properties of BN SiC Coated Hi Nicalon and Sylramic SiC Fiber Preforms written by National Aeronautics and Space Administration (NASA) and published by Createspace Independent Publishing Platform. This book was released on 2018-06-19 with total page 28 pages. Available in PDF, EPUB and Kindle. Book excerpt: Batch to batch and within batch variations, and the influence of fiber architecture on room temperature physical and tensile properties of BN/SiC coated Hi-Nicalon and Sylramic SiC fiber preform specimens were determined. The three fiber architectures studied were plain weave (PW), 5-harness satin (5HS) and 8-harness satin (8HS) Results indicate that the physical properties vary up to 10 percent within a batch, and up to 20 percent between batches of preforms. Load-reload (Hysteresis) and acoustic emission methods were used to analyze damage accumulation occurring during tensile loading. Early acoustic emission activity, before observable hysteretic behavior, indicates that the damage starts with the formation of nonbridged tunnel cracks. These cracks then propagate and intersect the load bearing "0" fibers giving rise to hysteretic behavior, For the Hi-Nicalon preform specimens, the onset of "0" bundle cracking stress and strain appeared to be independent of the fiber architecture. Also, the "0" fiber bundle cracking strain remained nearly the same for the preform specimens of both fiber types. Transmission Electron Microscope (TEM) analysis indicates that the Chemical Vapor Infiltration (CVI) Boron Nitride (BN) interface coating is mostly amorphous and contains carbon and oxygen impurities, and the CVI SiC coating is crystalline. No reaction exists between the CVI BN and SiC coating. Bhatt, Ramakrishna T. and Chen, Yuan L. and Morscher, Gregory N. Glenn Research Center NASA/TM-2001-210695, NAS 1.15:210695, E-12626
Download or read book TMS 2013 142nd Annual Meeting and Exhibition written by The Minerals, Metals & Materials Society (TMS) and published by John Wiley & Sons. This book was released on 2013-02-22 with total page 1238 pages. Available in PDF, EPUB and Kindle. Book excerpt: Presenting papers from the 2013 annual meeting of The Minerals, Metals & Materials Society (TMS), this volume covers developments in all aspects of high temperature electrochemistry, from the fundamental to the empirical and from the theoretical to the applied.
Download or read book Tensile Properties and Microstructural Characterization of Hi Nicalon SiC RBSN Composites written by and published by . This book was released on 1998 with total page 16 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book The Journal of the Acoustical Society of America written by Acoustical Society of America and published by . This book was released on 2003 with total page 1678 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book International Aerospace Abstracts written by and published by . This book was released on 1999 with total page 1016 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Effects of High Temperature Argon Heat Treatment on Tensile Strength and Microstructure of BN SiC Coated SiC Fiber Preforms written by and published by . This book was released on 1999 with total page 18 pages. Available in PDF, EPUB and Kindle. Book excerpt: Preforms of BN/SiC coated Hi-Nicalon and Sylramic SiC fibers were heat treated under 0.1 MPa argon pressure between 1000 deg to 1800 deg C for 1 and 100h. The effects of high temperature exposure on physical dimensions, weight, room temperature tensile strength, and microstructure of preforms have been studied. Both preforms showed shrinkage and weight loss, and microstructural changes beyond 1000 deg C. After 100 hr exposure, the Hi-Nicalon preforms showed strength degradation beyond 1200 deg C. The mechanisms of the strength degradation appear to be grain growth of the SiC fibers and crystallization of the BN coating. After 100 hr, the Sylramic preforms heat treated to 1000 deg C retained their as-produced strength while some of those heat-treated between 1000 deg and 1800 deg C showed strength degradation and others did not. At 1800 deg C, the ultimate tensile strength decreased with increasing time of exposure. Reasons for strength degradation of Sylramic preforms are being investigated.
Download or read book Ceramic Abstracts written by and published by . This book was released on 1999 with total page 256 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Handbook of Ceramic Composites written by Narottam P. Bansal and published by Springer Science & Business Media. This book was released on 2006-08-25 with total page 547 pages. Available in PDF, EPUB and Kindle. Book excerpt: This valuable handbook has been compiled by internationally renowned researchers in the field. Each chapter is focused on a specific composite system or a class of composites, presenting a detailed description of processing, properties, and applications.
Download or read book Heat Treatment Effects on Microstructure of SiC Fiber Preforms written by and published by . This book was released on 1999 with total page 18 pages. Available in PDF, EPUB and Kindle. Book excerpt: Preforms of BN/SiC coated Sylramic SiC fibers were heat treated at 1420 deg, 1600 deg, and 1800 deg C in 0.1 MPa argon or at 1800 deg C in 103 MPa nitrogen for 1 h. Optical, SEM, and TEM techniques were used to analyze the effects of environmental exposure on constituent microstructure of the preforms. TEM analysis of the as-received preforms indicates that the CVI BN coating is predominantly amorphous with small amounts of microcrystalline BN grains, and that the SiC coating on top of the BN coating and SiC fibers is polycrystalline. With increasing temperature of exposure from 1420 deg to 1800 deg C, the preforms heat treated in argon showed increasing amounts of crystalline BN in the CVI BN coating, and coarsening of SiC grains in the CVI SiC coating and SiC fibers. On the other hand, the preforms heal treated in 103 MPa nitrogen at 1800 deg C for 1 h showed microstructural changes inside the fiber tows similar to those heat treated at 1800 deg C in 0.1 MPa argon for 1 h, but the same preforms on the outer periphery of the tows showed reaction between nitrogen and the CVI SiC coating to form Si3N4.
Download or read book Environmental Barrier Coatings written by Kang N. Lee and published by MDPI. This book was released on 2020-12-29 with total page 168 pages. Available in PDF, EPUB and Kindle. Book excerpt: The global increase in air travel will require commercial vehicles to be more efficient than ever before. Advanced engine hot section materials are a key technology required to keep fuel consumption and emission to a minimum in next-generation gas turbines. Ceramic matrix composites (CMCs) are the most promising material to revolutionize gas turbine hot section materials technology because of their excellent high‐temperature properties. Rapid surface recession due to volatilization by water vapor is the Achilles heel of CMCs. Environmental barrier coatings (EBCs) is an enabling technology for CMCs, since it protects CMCs from water vapor. The first CMC component entered into service in 2016 in a commercial engine, and more CMC components are scheduled to follow within the next few years. One of the most difficult challenges to CMC components is EBC durability, because failure of EBC leads to a rapid reduction in CMC component life. Key contributors to EBC failure include recession, oxidation, degradation by calcium‐aluminum‐magnesium silicates (CMAS) deposits, thermal and thermo‐mechanical strains, particle erosion, and foreign object damage (FOD). Novel EBC chemistries, creative EBC designs, and robust processes are required to meet EBC durability challenges. Engine-relevant testing, characterization, and lifing methods need to be developed to improve EBC reliability. The aim of this Special Issue is to present recent advances in EBC technology to address these issues. In particular, topics of interest include but are not limited to the following: • Novel EBC chemistries and designs; • Processing including plasma spray, suspension plasma spray, solution precursor plasma spray, slurry process, PS-PVD, EB-PVD, and CVD; • Testing, characterization, and modeling; • Lifing.
Download or read book Metal and Ceramic Matrix Composites written by Brian Cantor and published by CRC Press. This book was released on 2003-11-01 with total page 432 pages. Available in PDF, EPUB and Kindle. Book excerpt: With contributions from leading experts in their respective fields, Metal and Ceramic Matrix Composites provides a comprehensive overview of topics on specific materials and trends. It is a subject regularly included as a final year option in materials science courses and is also of much industrial and academic interest. The book begins wit
Download or read book Ceramic Matrix Composites written by Narottam P. Bansal and published by John Wiley & Sons. This book was released on 2014-10-27 with total page 725 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book is a comprehensive source of information on various aspects of ceramic matrix composites (CMC). It covers ceramic and carbon fibers; the fiber-matrix interface; processing, properties and industrial applications of various CMC systems; architecture, mechanical behavior at room and elevated temperatures, environmental effects and protective coatings, foreign object damage, modeling, life prediction, integration and joining. Each chapter in the book is written by specialists and internationally renowned researchers in the field. This book will provide state-of-the-art information on different aspects of CMCs. The book will be directed to researchers working in industry, academia, and national laboratories with interest and professional competence on CMCs. The book will also be useful to senior year and graduate students pursuing degrees in ceramic science and engineering, materials science and engineering, aeronautical, mechanical, and civil or aerospace engineering. Presents recent advances, new approaches and discusses new issues in the field, such as foreign object damage, life predictions, multiscale modeling based on probabilistic approaches, etc. Caters to the increasing interest in the application of ceramic matrix composites (CMC) materials in areas as diverse as aerospace, transport, energy, nuclear, and environment. CMCs are considered ans enabling technology for advanced aeropropulsion, space propulsion, space power, aerospace vehicles, space structures, as well as nuclear and chemical industries. Offers detailed descriptions of ceramic and carbon fibers; fiber-matrix interface; processing, properties and industrial applications of various CMC systems; architecture, mechanical behavior at room and elevated temperatures, environmental effects and protective coatings, foreign object damage, modeling, life prediction, integration/joining.
Download or read book The Handbook of Advanced Materials written by and published by John Wiley & Sons. This book was released on 2004-04-27 with total page 656 pages. Available in PDF, EPUB and Kindle. Book excerpt: Written to educate readers about recent advances in the area of new materials used in making products. Materials and their properties usually limit the component designer. * Presents information about all of these advanced materials that enable products to be designed in a new way * Provides a cost effective way for the design engineer to become acquainted with new materials * The material expert benefits by being aware of the latest development in all these areas so he/she can focus on further improvements
Download or read book Structural Composite Materials written by F. C. Campbell and published by ASM International. This book was released on 2010-01-01 with total page 622 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book deals with all aspects of advanced composite materials; what they are, where they are used, how they are made, their properties, how they are designed and analyzed, and how they perform in-service. It covers both continuous and discontinuous fiber composites fabricated from polymer, metal, and ceramic matrices, with an emphasis on continuous fiber polymer matrix composites.
Download or read book Composite Materials written by Krishan K. Chawla and published by Springer Science & Business Media. This book was released on 2013-04-17 with total page 491 pages. Available in PDF, EPUB and Kindle. Book excerpt: Focusing on the relationship between structure and properties, this is a well-balanced treatment of the mechanics and the materials science of composites, while not neglecting the importance of processing. This updated second edition contains new chapters on fatigue and creep of composites, and describes in detail how the various reinforcements, the materials in which they are embedded, and of the interfaces between them, control the properties of the composite materials at both the micro- and macro-levels. Extensive use is made of micrographs and line drawings, and examples of practical applications in various fields are given throughout the book, together with extensive references to the literature. Intended for use in graduate and upper-division undergraduate courses, this book will also prove a useful reference for practising engineers and researchers in industry and academia.
