Download or read book Magnet Misalignment Studies for the Front end of the Neutrino Factory written by and published by . This book was released on 2013 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: In the Neutrino Factory front-end the muon beam coming from the interaction of a high-power (4 MW) proton beam on a mercury jet target is transformed through a buncher, a phase rotator and an ionization cooling channel before entering the downstream acceleration system. The muon front-end channel is densely packed with solenoid magnets, normal conducting radio-frequency cavities and absorber windows for the cooling section. The tolerance to the misalignment of the different components has to be determined in order on one hand to set the limits beyond which the performance of the front-end channel would be degraded; on the other hand to optimize the design and assembly of the front-end cells such that the component alignment can be checked and corrected for where crucial for the performance of the channel. In this paper we show the results of some of the simulations of the front-end channel performance where the magnetic field direction has been altered compared to the baseline.
Download or read book Studies of the Front End of a Neutrino Factory written by and published by . This book was released on 2001 with total page 3 pages. Available in PDF, EPUB and Kindle. Book excerpt: A neutrino factory employs muons which are produced, collected, cooled, accelerated and then stored so that their eventual decay produces an intense neutrino beam. A general description may be found in the paper by Geer [S. Geer, Phys. Rev. D, 57, 1 (1998)], and two upcoming Comments on Nuclear and Particle Physics articles [S. Geer, ''Future prospects for muon facilities'', see http://www-mucool.fnal.gov/mcnotes/muc0154.ps; also A. M. Sessler, ''Neutrino Factories: The Facility'', http://www-mucool.fnal.gov/mcnotes/muc0155.pdf]. In this contribution, we use analytic and numerical tools to investigate the performance of the front end of a neutrino factory. This region starts just after the target and ends just prior to the recirculating accelerators. Extensive previous work has resulted in designs used in the Fermilab Study of 1999-2000 and the Brookhaven Study of 2000-2001. Here we explore variations away from these particular designs, seeking possible improvements in final muon output, risk reduction, and ultimate cost. Our studies include changes in the overall front end geometry through optimization of the induction linac design and variations of the rf frequency in the cooling channel acceleration, and initial exploration of the use of helical wiggler fields to increase the range of initial muon energies that are captured.
Download or read book Neutrino Factory and Muon Collider Fellow Final Technical Report for DOE Award DE FG02 03ER41267 written by and published by . This book was released on 2006 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: By providing an intense, well controlled, well characterized, narrow beam of muon neutrinos (?????????s) and electron antineutrinos (–?e’s) from the decay of muons (?−??2019?s) in a storage ring, a neutrino factory can advance neutrino physics beyond the current round of approved and proposed experiments using conventional neutrino beams produced from a beam of decaying pions and kaons [1, 2]. There is no other comparable single clean source of electron neutrinos (from the decay of ?+’s) or antineutrinos. A muon storage ring producing 1019 to 1021 muon decays per year should be feasible. These intense neutrino beams can be used to study neutrino oscillations and possible CP violation. An entry-level muon storage ring that could provide 1019 decays per year would allow a determination of the sign of ?m231and a first measurement of sin22?13 for favorable values of this parameter. An improved muon storage ring system that could provide 1020 muon decays per year would allow measurement of sin22?13 to 1̃0−4. A high performance muon storage ring capable of providing more than 1020 muon decays per year would allow the exciting possibility of a measurement of CP violation in the leptonic sector. An intense cold muon beam at the front end of a neutrino factory could enable a rich variety of precision muon physics, such as a more precise measurement of the muon anomalous magnetic moment (g – 2) and searches for ? -> e ? and ?−N -> e− N conversion [3]. In addition, colliding beams of ?+ and ?− in a muon collider can provide an effective ?Higgs factory? or multi-TeV center-of-mass energy collisions [4]. A muon collider will be the best way to study the Higgs bosons associated with supersymmetric theories and may be necessary to discover them. Two neutrino factory feasibility studies have been carried out in the U.S. [5, 6]. International design efforts are now under way. The International Neutrino Factory and Superbeam Scoping Study (ISS) [7] began at the NuFact05 Workshop in June 2005 with the goals of elaborating the physics case, defining the baseline options for such a facility and its neutrino detectors, and identifying the required R&D program to lay the foundations for a complete design study proposal, and an International Design Study of the Neutrino Factory is beginning. These studies entail iterative cost and technical difficulty evaluations, thereby providing guidelines for the advancing R&D program. One of the central subsystems of a neutrino factory or muon collider is the muon cooling system. The muon beam is cooled to increase the phase space density and allow the muons to pass through smaller apertures, thus reducing the cost of the following accelerator systems. This cooling is accomplished through ionization cooling, in which the beam is passed through liquid hydrogen absorbers and then accelerated in RF cavities to restore the longitudinal momentum. Ionization cooling was proposed more than twenty years ago [8] but has not yet been demonstrated in practice. The International Muon Ionization Cooling Experiment (MICE) [9, 10] seeks to build and operate a muon-cooling device of a design proposed in Feasibility Study-II [6]. In addition to cooling the muons, MICE includes apparatus to measure the performance of the device. The experiment will be carried out by a collaboration of physicists from the U.S., Europe, and Japan at the Rutherford Appleton Laboratory in the U.K. MICE will begin operation in late 2007. Successful performance of the MICE experiment will provide the understanding needed to design a complete neutrino factory, in which the muons are cooled, accelerated, circulated in a storage ring, and decay to produce the neutrino beam. The first neutrino factory might be built in the U.S., Europe, or Japan. A Muon Collider Task Force (MCTF) has recently been organized at Fermilab.
Download or read book Interim Design Report for the International Design Study for a Neutrino Factory written by and published by . This book was released on 2011 with total page 272 pages. Available in PDF, EPUB and Kindle. Book excerpt: The starting point for the International Design Study for the Neutrino Factory (the IDS-NF) was the output of the earlier International Scoping Study for a future Neutrino Factory and super-beam facility (the ISS). The accelerator facility described in section 2 incorporates the improvements that have been derived from the substantial amount of work carried out within the Accelerator Working Group. Highlights of these improvements include: (1) Initial concepts for the implementation of the proton driver at each of the three example sites, CERN, FNAL, and RAL; (2) Detailed studies of the energy deposition in the target area; (3) A reduction in the length of the muon beam phase-rotation and bunching systems; (4) Detailed analyses of the impact of the risk that stray magnetic field in the accelerating cavities in the ionization cooling channel will reduce the maximum operating gradient. Several alternative ionization-cooling lattices have been developed as fallback options to mitigate this technical risk; (5) Studies of particle loss in the muon front-end and the development of strategies to mitigate the deleterious effects of such losses; (6) The development of more complete designs for the muon linac and re-circulating linacs; (7) The development of a design for the muon FFAG that incorporates insertions for injection and extraction; and (8) Detailed studies of diagnostics in the decay ring. Other sub-systems have undergone a more 'incremental' evolution; an indication that the design of the Neutrino Factory has achieved a degree of maturity. The design of the neutrino detectors described in section 3 has been optimized and the Detector Working Group has made substantial improvements to the simulation and analysis of the Magnetized Iron Neutrino Detector (MIND) resulting in an improvement in the overall neutrino-detection efficiency and a reduction in the neutrino-energy threshold. In addition, initial consideration of the engineering of the MIND has generated a design that is feasible and a finite element analysis of the toroidal magnetic field to produce a realistic field map has been carried out. Section 3 also contains, for the first time, a specification for the near-detector systems and a demonstration that the neutrino flux can be determined with a precision of 1% through measurements of inverse muon decay at the near detector. The performance of the facility, the work of the Physics and Performance Evaluation Group, is described in section 1. The effect of the improved MIND performance is to deliver a discovery reach for CP-invariance violation in the lepton sector, the determination of the mass hierarchy, and of?13 that extends down to values of sin2 2?13 H"5 x 10−5 and is robust against systematic uncertainties. In addition, the improved neutrino-energy threshold has allowed an indicative analysis of the kind of re-optimization of the facility that could be carried out should?13 be found close to the current upper bound. The results presented in section 1 demonstrate that the discovery reach as well as the precision with which the oscillation parameters can be measured at the baseline Neutrino Factory is superior to that of other proposed facilities for all possible values of sin2 2?13.
Download or read book POLARIZATION EFFECTS IN THE FRONT END OF THE NEUTRINO FACTORY written by and published by . This book was released on 2000 with total page 8 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Energy Research Abstracts written by and published by . This book was released on 1991 with total page 678 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book High Luminosity Large Hadron Collider HL LHC written by G.. Apollinari and published by . This book was released on 2017 with total page 516 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Particle Physics Reference Library written by Christian W. Fabjan and published by Springer Nature. This book was released on 2020 with total page 1083 pages. Available in PDF, EPUB and Kindle. Book excerpt: This second open access volume of the handbook series deals with detectors, large experimental facilities and data handling, both for accelerator and non-accelerator based experiments. It also covers applications in medicine and life sciences. A joint CERN-Springer initiative, the "Particle Physics Reference Library" provides revised and updated contributions based on previously published material in the well-known Landolt-Boernstein series on particle physics, accelerators and detectors (volumes 21A, B1,B2,C), which took stock of the field approximately one decade ago. Central to this new initiative is publication under full open access
Download or read book Government Reports Announcements Index written by and published by . This book was released on 1984 with total page 766 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Semiconductor Detector Systems written by Helmuth Spieler and published by OUP Oxford. This book was released on 2005-08-25 with total page 513 pages. Available in PDF, EPUB and Kindle. Book excerpt: Semiconductor sensors patterned at the micron scale combined with custom-designed integrated circuits have revolutionized semiconductor radiation detector systems. Designs covering many square meters with millions of signal channels are now commonplace in high-energy physics and the technology is finding its way into many other fields, ranging from astrophysics to experiments at synchrotron light sources and medical imaging. This book is the first to present a comprehensive discussion of the many facets of highly integrated semiconductor detector systems, covering sensors, signal processing, transistors and circuits, low-noise electronics, and radiation effects. The diversity of design approaches is illustrated in a chapter describing systems in high-energy physics, astronomy, and astrophysics. Finally a chapter "Why things don't work" discusses common pitfalls. Profusely illustrated, this book provides a unique reference in a key area of modern science.
Download or read book Critical Materials Strategy written by Steven Chu and published by DIANE Publishing. This book was released on 2011-05 with total page 166 pages. Available in PDF, EPUB and Kindle. Book excerpt: This report examines the role of rare earth metals and other materials in the clean energy economy. It was prepared by the U.S. Department of Energy (DoE) based on data collected and research performed during 2010. In the report, DoE describes plans to: (1) develop its first integrated research agenda addressing critical materials, building on three technical workshops convened by the DoE during November and December 2010; (2) strengthen its capacity for information-gathering on this topic; and (3) work closely with international partners, including Japan and Europe, to reduce vulnerability to supply disruptions and address critical material needs. Charts and tables. This is a print on demand report.
Download or read book Handbook of Magnetic Measurements written by Slawomir Tumanski and published by CRC Press. This book was released on 2016-04-19 with total page 398 pages. Available in PDF, EPUB and Kindle. Book excerpt: Collecting state-of-the-art knowledge from information scattered throughout the literature, this handbook describes magnetic materials and sensors, the testing of magnetic materials, and applications of magnetic measurements. It presents an up-to-date, accessible account of modern magnetic measurement techniques. The book discusses the fundamentals of magnetism and covers contemporary magnetic materials and sensors. It also explores applications of magnetic diagnostics in medicine, magnetoarcheology, and magnetic imaging. An extensive list of references is included at the end of each chapter.
Download or read book LHC Design Report written by and published by . This book was released on 2004 with total page 560 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Neutrinos in Particle Physics Astronomy and Cosmology written by Zhizhong Xing and published by Springer Science & Business Media. This book was released on 2011-06-08 with total page 434 pages. Available in PDF, EPUB and Kindle. Book excerpt: "Neutrinos in Particle Physics, Astronomy and Cosmology" provides a comprehensive and up-to-date introduction to neutrino physics, neutrino astronomy and neutrino cosmology. The intrinsic properties and fundamental interactions of neutrinos are described, as is the phenomenology of lepton flavor mixing, seesaw mechanisms and neutrino oscillations. The cosmic neutrino background, stellar neutrinos, supernova neutrinos and ultrahigh-energy cosmic neutrinos, together with the cosmological matter-antimatter asymmetry and other roles of massive neutrinos in cosmology, are discussed in detail. This book is intended for researchers and graduate students in the fields of particle physics, particle astrophysics and cosmology. Dr. Zhizhong Xing is a professor at the Institute of High Energy Physics, Chinese Academy of Sciences, China; Dr. Shun Zhou is currently a postdoctoral fellow at the Max Planck Institute for Physics, Germany.
Download or read book Handbook of Accelerator Physics and Engineering written by Alex Chao and published by World Scientific. This book was released on 1999 with total page 702 pages. Available in PDF, EPUB and Kindle. Book excerpt: Edited by internationally recognized authorities in the field, this handbook focuses on Linacs, Synchrotrons and Storage Rings and is intended as a vade mecum for professional engineers and physicists engaged in these subjects. Here one will find, in addition to the common formulae of previous compilations, hard to find specialized formulae, recipes and material data pooled from the lifetime experiences of many of the world's most able practitioners of the art and science of accelerator building and operation.
Download or read book Particle Accelerator Physics written by Helmut Wiedemann and published by Springer Science & Business Media. This book was released on 2013-11-11 with total page 457 pages. Available in PDF, EPUB and Kindle. Book excerpt: Particle Accelerator Physics covers the dynamics of relativistic particle beams, basics of particle guidance and focusing, lattice design, characteristics of beam transport systems and circular accelerators. Particle-beam optics is treated in the linear approximation including sextupoles to correct for chromatic aberrations. Perturbations to linear beam dynamics are analyzed in detail and correction measures are discussed, while basic lattice design features and building blocks leading to the design of more complicated beam transport systems and circular accelerators are studied. Characteristics of synchrotron radiation and quantum effects due to the statistical emission of photons on particle trajectories are derived and applied to determine particle-beam parameters. The discussions specifically concentrate on relativistic particle beams and the physics of beam optics in beam transport systems and circular accelerators such as synchrotrons and storage rings. This book forms a broad basis for further, more detailed studies of nonlinear beam dynamics and associated accelerator physics problems, discussed in the subsequent volume.
Download or read book The Large Hadron Collider written by Lyndon R. Evans and published by EPFL Press. This book was released on 2009-01-01 with total page 264 pages. Available in PDF, EPUB and Kindle. Book excerpt: Describes the technology and engineering of the Large Hadron collider (LHC), one of the greatest scientific marvels of this young 21st century. This book traces the feat of its construction, written by the head scientists involved, placed into the context of the scientific goals and principles.
