Download or read book An Introduction to Corrosion and Protection of Metals written by Gosta Wranglen and published by Springer. This book was released on 1985-05-30 with total page 288 pages. Available in PDF, EPUB and Kindle. Book excerpt: Corrosion may be defined as an unintentional attack on a material through reaction with a surrounding medium. The term can refer to a process or to the damage caused by such a process. According to this general definition, materials other than metals, such as ceramics, plastics or concrete, may also be subject to corrosion (or corrode). When no particular reference is made to the material, however, it is normally understood that a metal is being attacked. It is entirely in this limited sense that the term is used in this book. There are good reasons for treating the corrosion of metals separately, apart from deterioration or decay of other materials. Since metals have a high electric conductivity, their corrosion is usually of an electrochemical nature. The chemical deterioration of electrically non-conducting ma terials, such as plastics and ceramics, is governed by other physico-chemical principles. It is necessary to devote more attention to metallic corrosion nowadays than earlier, due to 1. An increased use of metals within all fields of technology. 2. The use for special applications, e.g. within the atomic energy field, of rare and expensive metals, whose preservation requires particular precautions. 3. A more corrosive environment due to the increasing pollution of air and water. 4. The use of metallic constructions of more slender dimensions which do not tolerate corrosive attacks to the same extent as did the heavy constructions used in the old days.
Download or read book An Introduction to Corrosion and Protection of Metals written by Gösta Wranglén and published by . This book was released on 1972 with total page 304 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Corrosion and Protection of Metals written by David M Bastidas and published by . This book was released on 2020-09-16 with total page 242 pages. Available in PDF, EPUB and Kindle. Book excerpt: Introduction and Scope-During the last few decades, an enormous effort has been made to understand corrosion phenomena and their mechanisms, and to elucidate the causes that dramatically influence the service lifetime of metal materials. The performance of metal materials in aggressive environments is critical for a sustainable society. The failure of the material in service impacts the economy, the environment, health, and society. In this regard, corrosion-based economic losses due to maintenance, repair, and the replacement of existing structures and infrastructure account for up to 4% of gross domestic product (GDP) in well developed countries. One of the biggest issues in corrosion engineering is estimating service lifetime. Corrosion prediction has become very difficult, as there is no direct correlation with service lifetime and experimental lab results, usually as a result of discrepancies between accelerated testing and real corrosion processes. It is of major interest to forecast the impact of corrosion-based losses on society and the global economy, since existing structures and infrastructure are becoming old, and crucial decisions now need to be made to replace them. On the other hand, environmental protocols seek to reduce greenhouse effects. Therefore, low emission policies, in force, establish regulations for the next generation of materials and technologies. Advanced technologies and emergent materials will enable us to get through the next century. Great advances are currently in progress for the development of corrosion-resistant metal materials for different sectors, such as energy, transport, construction, and health. This Special Issue on the corrosion and protection of metals is focused on current trends in corrosion science, engineering, and technology, ranging from fundamental to applied research, thus covering subjects related to corrosion mechanisms and modelling, protection and inhibition processes, and mitigation strategies.
Download or read book Passivity and Protection of Metals Against Corrosion written by N. D. Tomashov and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 182 pages. Available in PDF, EPUB and Kindle. Book excerpt: Considerable progress has been made in the past 20 years toward understanding the basic mechanisms of corrosion, and the application of this knowledge to its control. From the very beginning, educational institutions and industrial research laboratories have contributed greatly toward determining and elucidating the fundamental principles of corrosion reactions. Some of the basic principles involved in cor rosion of metals can be credited to early investigators. Michael Faraday in 1830-1840 studied the relationship between the quantity of a metal dissolved and the electric current which was produced by this reaction. He also proposed that the passivation of iron was through the formation of a film and that the dissolution of a metal was electro chemical in nature. Sir Humphrey Davy in 1824 worked out the funda mentals of galvanic corrosion of ships' hulls and applied sacrificial zinc anodes to protect them from sea water corrosion. Richard Arlie in 1847 demonstrated that corrosion produced by oxygen at the surface of iron in a flowing stream generated a current. With the fundamental knowledge available to him from these early investigators, Willis Rodney Whitney developed and expressed, in its most useful form, one of the basic scientific principles which provides modern corrosion specialists with a fundamental basis of corrosion control. Dr. Whitney concluded that corrosion of iron is electrochemical, and that the rate is simply a function of the electromotive force and resistance of the circuit.
Download or read book An Introduction to Corrosion and Protection of Metals written by Gosta Wranglen and published by . This book was released on 1987 with total page 287 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Introduction to Corrosion Science written by E. McCafferty and published by Springer Science & Business Media. This book was released on 2010-01-04 with total page 583 pages. Available in PDF, EPUB and Kindle. Book excerpt: This textbook is intended for a one-semester course in corrosion science at the graduate or advanced undergraduate level. The approach is that of a physical chemist or materials scientist, and the text is geared toward students of chemistry, materials science, and engineering. This textbook should also be useful to practicing corrosion engineers or materials engineers who wish to enhance their understanding of the fundamental principles of corrosion science. It is assumed that the student or reader does not have a background in electrochemistry. However, the student or reader should have taken at least an undergraduate course in materials science or physical chemistry. More material is presented in the textbook than can be covered in a one-semester course, so the book is intended for both the classroom and as a source book for further use. This book grew out of classroom lectures which the author presented between 1982 and the present while a professorial lecturer at George Washington University, Washington, DC, where he organized and taught a graduate course on “Environmental Effects on Materials.” Additional material has been provided by over 30 years of experience in corrosion research, largely at the Naval Research Laboratory, Washington, DC and also at the Bethlehem Steel Company, Bethlehem, PA and as a Robert A. Welch Postdoctoral Fellow at the University of Texas. The text emphasizes basic principles of corrosion science which underpin extensions to practice.
Download or read book Corrosion and Its Control written by H. VanDroffelaar and published by National Assn of Corrosion Engineers. This book was released on 1994-12-31 with total page 332 pages. Available in PDF, EPUB and Kindle. Book excerpt: A text that emphasizes the engineering aspects of corrosion and its control in ways helpful to practicing engineers, based on notes used by the authors for an advanced undergraduate engineering course at Queen's U., Kingston, Ontario. This revised and expanded edition places particular emphasis on u
Download or read book Introduction to Corrosion and Protection of Metals written by G. Wranglen and published by . This book was released on 1972 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book An Introduction to Corrosion and Protection of Metals written by Gosta Wrangten and published by . This book was released on 1977 with total page 288 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Corrosion of Metals written by Helmut Kaesche and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 604 pages. Available in PDF, EPUB and Kindle. Book excerpt: Corrosion due to water is one of the most significant and complex causes of damage to metallic products. Written from the viewpoint of physical chemistry, this authoritative and established text deals with the aqueous corrosion of metals. Available for the first time in English, Corrosion of Metal addressing engineers, metallurgists, physicists and chemists. This self-contained, valuable reference comprehensively organizes and makes readily accessible the accumulated wealth of fundamental and applied knowledge. The concentration is on the underlying essentials of corrosion and failure, and the material is consistently presented in relation to practical applications to corrosion protection. The first chapters introducing the physicochemical principles are ideal for students. The following chapters provide an overview of the state of research for those familiar with the fundamentals. An exhaustive bibliography and appendices conclude the volume.
Download or read book Handbook of Hot dip Galvanization written by Peter Maaß and published by John Wiley & Sons. This book was released on 2011-03-31 with total page 460 pages. Available in PDF, EPUB and Kindle. Book excerpt: Hot-dip galvanization is a method for coating steel workpieces with a protective zinc film to enhance the corrosion resistance and to improve the mechanical material properties. Hot-dip galvanized steel is the material of choice underlying many modern buildings and constructions, such as train stations, bridges and metal domes. Based on the successful German version, this edition has been adapted to include international standards, regulations and best practices. The book systematically covers all steps in hot-dip galvanization: surface pre-treatment, process and systems technology, environmental issues, and quality management. As a result, the reader finds the fundamentals as well as the most important aspects of process technology and technical equipment, alongside contributions on workpiece requirements for optimal galvanization results and methods for applying additional protective coatings to the galvanized pieces. With over 200 illustrated examples, step-by-step instructions, presentations and reference tables, this is essential reading for apprentices and professionals alike.
Download or read book An Introduction to Corrosion and Protection of Metals written by Gosta Wranglen and published by Springer. This book was released on 1985-05-15 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: Corrosion may be defined as an unintentional attack on a material through reaction with a surrounding medium. The term can refer to a process or to the damage caused by such a process. According to this general definition, materials other than metals, such as ceramics, plastics or concrete, may also be subject to corrosion (or corrode). When no particular reference is made to the material, however, it is normally understood that a metal is being attacked. It is entirely in this limited sense that the term is used in this book. There are good reasons for treating the corrosion of metals separately, apart from deterioration or decay of other materials. Since metals have a high electric conductivity, their corrosion is usually of an electrochemical nature. The chemical deterioration of electrically non-conducting ma terials, such as plastics and ceramics, is governed by other physico-chemical principles. It is necessary to devote more attention to metallic corrosion nowadays than earlier, due to 1. An increased use of metals within all fields of technology. 2. The use for special applications, e.g. within the atomic energy field, of rare and expensive metals, whose preservation requires particular precautions. 3. A more corrosive environment due to the increasing pollution of air and water. 4. The use of metallic constructions of more slender dimensions which do not tolerate corrosive attacks to the same extent as did the heavy constructions used in the old days.
Download or read book Principles of Metal Surface Treatment and Protection written by D. R. Gabe and published by Elsevier. This book was released on 2014-07-22 with total page 232 pages. Available in PDF, EPUB and Kindle. Book excerpt: Principles of Metal Surface Treatment and Protection deals with the principles of metal surface treatment and protection. Topics covered range from electrodeposition and hot dip coating to diffusion and non-metallic coatings, as well as oxide and conversion coatings. The theory of corrosion protection is also discussed. Comprised of eight chapters, this volume begins with an overview of the corrosion of metals and the scope of protection against corrosion, followed by a detailed treatment of electrodeposition. The discussion then turns to the principles of hot dipping as a coating method; the formation of a diffusion coating; and the role of a non-metallic coating in corrosion protection. Subsequent chapters focus on the protection of oxide films against corrosion by means of anodizing, phosphatizing, and the use of tin free steel; testing and selection of a particular coating for corrosion resistance applications; and the theory of corrosion protection. This book is intended for metal-finishing scientists and students of metallurgy and metal finishing.
Download or read book Corrosion Prevention and Protection written by Edward Ghali and published by John Wiley & Sons. This book was released on 2007-01-30 with total page 574 pages. Available in PDF, EPUB and Kindle. Book excerpt: Corrosion Prevention and Protection: Practical Solutions presents a functional approach to the various forms of corrosion, such as uniform corrosion, pitting corrosion, crevice corrosion, galvanic corrosion, stress corrosion, hydrogen-induced damage, sulphide stress cracking, erosion-corrosion, and corrosion fatigue in various industrial environments. The book is split into two parts. The first, consisting of five chapters: Introduction and Principles (Fundamentals) of Corrosion Corrosion Testing, Detection, Monitoring and Failure Analysis Regulations, Specifications and Safety Materials: Metals, Alloys, Steels and Plastics Corrosion Economics and Corrosion Management The second part of the book consists of two chapters which present: a discussion of corrosion reactions, media, active and active-passive corrosion behaviour and the various forms of corrosion, a collection of case histories and practical solutions which span a wide range of industrial problems in a variety of frequently encountered environments, including statues & monuments, corrosion problems in metallurgical and mineral processing plants, boilers, heat exchangers and cooling towers, aluminum and copper alloys, galvanized steel structures as well as hydrogeological environmental corrosion This text is relevant to researchers and practitioners, engineers and chemists, working in corrosion in industry, government laboratories and academia. It is also suitable as a course text for engineering students as well as libraries related to chemical and chemical engineering institutes and research departments.
Download or read book Electrocorrosion and Protection of Metals written by Joseph Riskin and published by Elsevier. This book was released on 2008-11-07 with total page 273 pages. Available in PDF, EPUB and Kindle. Book excerpt: Electrocorrosion, the corrosion of metallic constructions by external currents, is the most significant factor in conductive aggressive environments. Corrosion of underground and underwater metal constructions by stray currents has been comprehensively studied in the past decades and is considered here only in the form of a review. The primary attention is on corrosion, by external anodic (mainly) and cathodic currents, of metal constructions in the highly aggressive environments typical for electrochemical plants, where penetration of the external currents (leakage currents) from the electrolytic baths into metal constructions is unavoidable. A new approach to the problem of electrocorrosion protection of passive structural metals is considered in this book, keeping the metals attacked by external currents in the boundaries of their passive field. The systems, developed in accordance with this approach, are based on the modification of existing and elaboration of new methods of electrocorrosion protection. These systems take into account corrosion and electrochemical characteristics of the aggressive media (redox potential, conductivity etc.) and of the passive metal (corrosion and activation potentials, current density in a passive state, etc) as well as the sizes and distribution character of the external currents. The book covers analysis of leakage current distributions in electrochemical plants, their influence, methods to estimate corrosion stability of metallic structures subject to external currents and presents many concrete examples of the successful introduction of corrosion protection systems in operating plants. A new approach to protection from electrocorrosion, taking into account the passive state of the metal in aggressive media Newly developed and modifications of well known methods of electrocorrosion protection are presented Systematized data on electrocorrosion and protection of metals, especially in electrochemical plants, allow corrosion engineers, researchers and personnel maintaining the equipment of electrochemical plants to analyze the corrosion state of metallic equipment and prevent electrocorrosion
Download or read book Corrosion and Surface Chemistry of Metals written by Dieter Landolt and published by EPFL Press. This book was released on 2007-05-02 with total page 640 pages. Available in PDF, EPUB and Kindle. Book excerpt: Textbook; grad.
Download or read book Uhlig s Corrosion Handbook written by R. Winston Revie and published by John Wiley & Sons. This book was released on 2011-04-12 with total page 1299 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book serves as a reference for engineers, scientists, and students concerned with the use of materials in applications where reliability and resistance to corrosion are important. It updates the coverage of its predecessor, including coverage of: corrosion rates of steel in major river systems and atmospheric corrosion rates, the corrosion behavior of materials such as weathering steels and newer stainless alloys, and the corrosion behavior and engineering approaches to corrosion control for nonmetallic materials. New chapters include: high-temperature oxidation of metals and alloys, nanomaterials, and dental materials, anodic protection. Also featured are chapters dealing with standards for corrosion testing, microbiological corrosion, and electrochemical noise.
