Download or read book Push On Hose and Mating Hose Fittings written by Hydraulic Hose and Hose Fittings Committee and published by . This book was released on 2009 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This SAE standard provides limited, dimensional and general performance requirements for low pressure, field attachable, push-on hose and their mating hose fittings. The intended application is for fluid and pneumatic power used with petroleum base hydraulic fluids, lube oils, water glycols and air, within the temperature ranges listed in Table 1. The maximum working pressure is 1.7 MPa (see Table 2). For air applications the maximum working pressure is at 0.7 MPa. Hose and hose fittings are manufactured within certain dimensions with tolerance ranges in order to provide the proper gripping and sealing. SAE J2552 hose from one manufacturer may not be compatible with J2552 hose fittings supplied by another manufacturer. It is the responsibility of the fabricator to consult the manufacturers' written assembly instructions or the manufacturers directly before intermixing hose and hose fittings from two manufacturers. Always follow the manufacturers' instructions for proper preparation and fabrication of hose assemblies. Hose assemblies made to this standard shall not be used in dynamic motion, vibrating or impulsing applications, nor for brake hoses or fuel lines.This is a new document with the objective to standardize push-on hose and the mating hose fittings.

Download or read book Hydraulic Hose Fittings written by Hydraulic Hose and Hose Fittings Committee and published by . This book was released on 2011 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This SAE Standard provides general and dimensional specifications for the most common hose fittings used in conjunction with hydraulic hoses specified in SAE J517 and utilized in hydraulic systems on mobile and stationary equipment.The general specifications contained in Sections 1 through 15 are applicable to all hydraulic hose fittings and supplement the detailed specifications for the 100R-series fittings contained in the later sections of this document.This document shall be utilized as a procurement document only to the extent agreed upon by the manufacturer and user.Refer to SAE J517 for specifications of hose and information on hose assemblies. SAE J1273 contains information on application factors affecting hose fittings, hose, and hose assemblies.THE RATED WORKING PRESSURE OF A HOSE ASSEMBLY COMPRISING SAE J516 FITTINGS AND SAE J517 HOSE SHALL NOT EXCEED THE LOWER OF THE TWO WORKING PRESSURE RATED VALUES.The following are hose fitting types contained in this document: aMale dryseal pipe thread hose fittings shall be as shown in Figure 2 for the respective styles, and in Table 2 for the applicable hoses and sizes. bMale straight thread O-ring hose fittings shall be as shown in Figure 3 or the respective styles, and in Table 3 for the applicable hoses and sizes. cMale 37° flare hose fittings shall be as shown in Figure 4 for the respective styles, and in Table 4 for the applicable hoses and sizes. dFemale 37° flare hose fittings shall be as shown in Figures 5 to 5B for the respective styles and shapes, and in Tables 5 to 5B for the applicable hoses and sizes. eMale 45° flare hose fittings shall be as shown by the 37° figures and tables. fFemale 45° flare hose fittings shall be as shown by the 37° figures and tables. gMale flareless 24° cone hose fittings shall be as shown in Figure 6 and in Table 6 for the applicable hoses and sizes. hFemale flareless 24° cone hose fittings shall be as shown in Figure 7 and in Table 7 for the applicable hoses and sizes. i4-bolt split flange hose fittings shall be as shown in Figures 8 to 8F for the respective styles and shapes, and in Tables 8 to 8F for the applicable hoses and sizes. jMale O-ring face seal hose fittings shall be as shown in Figure 9 for the respective styles, and in Table 9 for the applicable hoses and sizes. kFemale O-ring face seal hose fittings shall be as shown in Figures 10 to 10B for the respective styles, and Tables 10 to 10B for the applicable hoses and sizes.It is recommended that where step sizes or additional types of fittings are required, they be designed to conform with the specifications of this document insofar as they may apply. The following general specifications shall supplement the dimensional data contained in the tables with respect to all unspecified detail. This document has been revised to add the bulkhead o-ring face seal fittings in Figure 11. Also, the Part Identification Number (PIN) in figures 10A and 10B as well as tables 10A and 10B have been corrected.In an effort to standardize within a global market and ensuring that companies can remain competitive in an international market, it is the intent to convert to metric hex sizes which will: lead to one global system guide users to preferred system reduce complexity eliminate duplicationsThe optional inch hexes now contain the note "NOT TO BE USED FOR NEW DESIGN" in accordance with the Metric Hex Resolution approved during the March 2008 FCCTC meeting.

Download or read book Hydraulic Hose Fittings HS 150 2000 written by Hydraulic Hose and Hose Fittings Committee and published by . This book was released on 1999 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This SAE Standard provides general and dimensional specifications for the most common hose fittings used in conjunction with hydraulic hoses specified in SAE J517 and utilized in hydraulic systems on mobile and stationary equipment. The general specifications contained in Sections 1 through 15 are applicable to all hydraulic hose fittings and supplement the detailed specifications for the 100R-series fittings contained in the later sections of this document. This document shall be utilized as a procurement document only to the extent agreed upon by the manufacturer and user. Refer to SAE J517 for specifications of hose and information on hose assemblies. SAE J1273 contains information on application factors affecting hose fittings, hose, and hose assemblies. NOTE: THE RATED WORKING PRESSURE OF A HOSE ASSEMBLY COMPRISING SAE J516 FITTINGS AND SAE J517 HOSE SHALL NOT EXCEED THE LOWER OF THE TWO WORKING PRESSURE RATED VALUES. The following are hose fitting types contained in this document: a. Male dryseal pipe thread type hose fittings shall be as shown in Figures 1A to 1C for the respective styles, and in Tables 1A to 1M for the applicable hoses and sizes. b. Male straight thread O-ring boss type hose fittings shall be as shown in Figures 2A and 2B for the respective styles, and in Tables 2A to 2H for the applicable hoses and sizes. c. Male 37-degree flared type hose fittings shall be as shown in Figures 3A to 3C for the respective styles, and in Tables 3A to 3L for the applicable hoses and sizes. d. Female 37-degree flared type hose fittings shall be as shown in Figures 4A to 7B for the respective styles and shapes, and in Tables 4A to 4M for the applicable hoses and sizes. e. Male 45-degree flared type hose fittings shall be as shown in Figures 8A and 8B for the respective styles, and in Tables 5A to 5E for the applicable hoses and sizes. f. Female 45-degree flared type hose fittings shall be as shown in Figures 9A to 12B for the respective styles and shapes, and in Tables 6A to 6E for the applicable hoses and sizes. g. Male flareless type hose fittings shall be as shown in Figures 13A and 13B for the respective styles, and in Tables 7A and 7B for the applicable hoses and sizes. h. Female flareless type hose fittings shall be as shown in Figures 14A to 14C for the respective styles, and in Tables 8A and 8B for the applicable hoses and sizes. i. 4-bolt split flange type hose fittings shall be as shown in Figures 15A to 21C for the respective styles and shapes, and in Tables 9A to 9I2 for the applicable hoses and sizes. j. Female O-ring face seal hose fittings shall be as shown in Figures 22A to 25B for the respective styles, and Tables 10A to 10L for the applicable hoses and sizes. It is recommended that where step sizes or additional types of fittings are required, they be designed to conform with the specifications of this document insofar as they may apply. The following general specifications shall supplement the dimensional data contained in the tables with respect to all unspecified detail.

Download or read book Hydraulic Hose Fitting for Marine Applications written by Hydraulic Hose and Hose Fittings Committee and published by . This book was released on 2014 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This SAE Standard covers general and performance specifications for hydraulic hose fittings of the styles, types, and classes defined in Section 3 and used in conjunction with nonmetallic flexible hoses for marine applications. This document does not ensure compatibility between manufacturers of hydraulic hose and hydraulic hose fittings. Compatibility is the responsibility of the hydraulic hose assembly manufacturer. The technical report covers technology, products, or processes which are mature and not likely to change in the foreseeable future.

Download or read book Handbook of Hose Pipes Couplings and Fittings written by Michael J. Barber and published by Elsevier Science & Technology. This book was released on 1985 with total page 428 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Hydraulic Hose Fittings for Marine Applications written by Hydraulic Hose and Hose Fittings Committee and published by . This book was released on 1996 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This SAE Standard covers general and performance specifications for hydraulic hose fittings of the styles, types, and classes defined in Section 3 and used in conjunction with nonmetallic flexible hoses for marine applications. This document does not ensure compatibility between manufacturers of hydraulic hose and hydraulic hose fittings. Compatibility is the responsibility of the hydraulic hose assembly manufacturer.

Download or read book BEADED TUBE HOSE FITTINGS written by Hydraulic Hose and Hose Fittings Committee and published by . This book was released on 1993 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This SAE Standard covers complete general and dimensional specifications for beaded tube hose fittings. These fittings are intended for general applications in low-pressure automotive and hydraulic systems on automotive, industrial, and commercial products. The fittings shown in Figures 1 to 3 and Table 1 are intended for use with low-pressure hose and shall be retained by hose clamps as specified in SAE J1508.

Download or read book Hose Fittings and Equipment written by Parker. Fluid Connectors and published by . This book was released on 1996 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Connections for Hydraulic Fluid Power and General Use Hose Fittings Hose Fittings with ISO 8434 2 37 0D Flared Ends written by British Standards Institute Staff and published by . This book was released on 2007-08-31 with total page 20 pages. Available in PDF, EPUB and Kindle. Book excerpt: Hose connectors, Flexible pipes, Pipe connections, Hydraulic equipment, Hydraulic transmission systems, Pipe couplings, Bend couplings, Swivel pipe connectors, Unalloyed steels, Dimensions, Performance, Designations, Screwed fittings, Threads

Download or read book HOSE PUSH ON FITTINGS written by Hydraulic Hose and Hose Fittings Committee and published by . This book was released on 1978 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This standard covers complete general and dimensional specifications for hose push-on fittings. These fittings are intended for general applications in low pressure automotive and hydraulic systems on automotive, industrial, and commercial products. The fittings shown in Figs. 13 and Table 2 are intended for use with low pressure hose and shall be retained by hose clamps as specified in SAE J536.

Download or read book Connections for Hydraulic Fluid Power and General Use Hose Fittings Hose Fittings with ISO 6149 Metric Stud Ends written by British Standards Institute Staff and published by . This book was released on 2007-08-31 with total page 18 pages. Available in PDF, EPUB and Kindle. Book excerpt: Hose connectors, Flexible pipes, Pipe connections, Hydraulic equipment, Hydraulic transmission systems, Stud couplings, Pipe couplings, Bend couplings, Unalloyed steels, Dimensions, Performance, Designations, Screwed fittings, Threads, Assembling

Download or read book FITTINGS CATALOG OF FLARED FLARELESS PIPE THREADED PORT HOSE AND OTHER TYPE TUBE STANDARD CONNECTORS written by G-3, Aerospace Couplings, Fittings, Hose, Tubing Assemblies and published by . This book was released on 1994 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: THIS AEROSPACE INFORMATION REPORT (AIR) IS WRITTEN AS AN AID FOR LOCATING AND IDENTIFYING VARIOUS FITTING DESIGNS AND CONFIGURATIONS THAT ARE DESIGNATED AS STANDARD PARTS.

Download or read book Connections for Hydraulic Fluid Power and General Use Hose Fittings Hose Fittings with ISO 8434 1 and ISO 8434 4 24 0d Cone Connector Ends with O Rings written by British Standards Institute Staff and published by . This book was released on 2003-07-16 with total page 22 pages. Available in PDF, EPUB and Kindle. Book excerpt: Hose connectors, Flexible pipes, Pipe connections, Hydraulic equipment, Hydraulic transmission systems, Fluid equipment, Steels, Dimensions, Design, Toroidal sealing rings, Pipe fittings

Download or read book Formed Tube Ends for Hose Connections and Hose Fittings written by Hydraulic Hose and Hose Fittings Committee and published by . This book was released on 2004 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This SAE standard provides general and dimensional specifications for formed tube ends and hose fittings. These connections are intended for general applications in low pressure automotive and hydraulic systems on automotive, industrial, and commercial products. The fittings shown in Figures 2 and 3 are intended to be retained by hose clamps as specified in SAE J1508. It is recommended that where step sizes or additional types of fittings are required, they be designed to conform with the specifications of this document insofar as they may apply. The following general specifications shall supplement the dimensional data contained in the tables with respect to all unspecified detail.The revisions represented in J1231 are the result of direct requests from the User community. The revision wll reduce the amount of force required to assemble the -16 size connections, resulting in more efficient assembly.

Download or read book Connections for Hydraulic Fluid Power and General Use Hose Fittings Hose Fittings with ISO 8434 6 60 0D Cone Ends written by British Standards Institute Staff and published by . This book was released on 2009-12-31 with total page 24 pages. Available in PDF, EPUB and Kindle. Book excerpt: Hose connectors, Flexible pipes, Pipe connections, Hydraulic equipment, Hydraulic transmission systems, Pipe couplings, Unalloyed steels, Dimensions, Performance, Designations, Screwed fittings, Threads

Download or read book HOSE ASSEMBLY PTFE ARAMID REINFORCED STANDARD DUTY 4000 3000 Psi 275 F TITANIUM FITTINGS FLARELESS STRAIGHT TO STRAIGHT written by G-3, Aerospace Couplings, Fittings, Hose, Tubing Assemblies and published by . This book was released on 1994 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Hose Fittings and Equipment written by Parker FluidConnectors and published by . This book was released on 1993 with total page 434 pages. Available in PDF, EPUB and Kindle. Book excerpt: