Download or read book Fundamental Studies in Selective Wet Etching and Corrosion Processes for High performance Semiconductor Devices written by Nabil George Mistkawi and published by . This book was released on 2010 with total page 198 pages. Available in PDF, EPUB and Kindle. Book excerpt: As multistep, multilayer processing in semiconductor industry becomes more complex, the role of cleaning solutions and etching chemistries are becoming important in enhancing yield and in reducing defects. This thesis demonstrates successful formulations that exhibit copper and tungsten compatibility, and are capable of Inter Layer Dielectric (ILD) cleaning and selective Ti etching. The corrosion behavior of electrochemically deposited copper thin films in deaerated and non-deaerated cleaning solution containing hydrofluoric acid (HF) has been investigated. Potentiodynamic polarization experiments were carried out to determine active, active-passive, passive, and transpassive regions. Corrosion rates were calculated from tafel slopes. ICP-MS and potentiodynamic methods yielded comparable Cu dissolution rates. Interestingly, the presence of hydrogen peroxide in the cleaning solution led to more than an order of magnitude suppression of copper dissolution rate. We ascribe this phenomenon to the formation of interfacial CuO which dissolves at slower rate in dilute HF. A kinetic scheme involving cathodic reduction of oxygen and anodic oxidation of Cu0 and Cu+1 is proposed. It was determined that the reaction order kinetics is first order with respect to both HF and oxygen concentrations. The learnings from copper corrosion studies were leveraged to develop a wet etch/clean formulation for selective titanium etching. The introduction of titanium hard-mask (HM) for dual damascene patterning of copper interconnects created a unique application in selective wet etch chemistry. A formulation that addresses the selectivity requirements was not available and was developed during the course of this dissertation. This chemical formulation selectively strips Ti HM film and removes post plasma etch polymer/residue while suppressing the etch rate of tungsten, copper, silicon oxide, silicon carbide, silicon nitride, and carbon doped silicon oxide. Ti etching selectivity exceeding three orders of magnitude was realized. Surprisingly, it exploits the use of HF, a chemical well known for its SiO2 etching ability, along with a silicon precursor to protect SiO2. The ability to selectively etch the Ti HM without impacting key transistor/interconnect components has enabled advanced process technology nodes of today and beyond. This environmentally friendly formulation is now employed in production of advanced high-performance microprocessors and produced in a 3000 gallon reactor.
Download or read book CRC Handbook of Metal Etchants written by Perrin Walker and published by CRC Press. This book was released on 1990-12-11 with total page 1434 pages. Available in PDF, EPUB and Kindle. Book excerpt: This publication presents cleaning and etching solutions, their applications, and results on inorganic materials. It is a comprehensive collection of etching and cleaning solutions in a single source. Chemical formulas are presented in one of three standard formats - general, electrolytic or ionized gas formats - to insure inclusion of all necessary operational data as shown in references that accompany each numbered formula. The book describes other applications of specific solutions, including their use on other metals or metallic compounds. Physical properties, association of natural and man-made minerals, and materials are shown in relationship to crystal structure, special processing techniques and solid state devices and assemblies fabricated. This publication also presents a number of organic materials which are widely used in handling and general processing...waxes, plastics, and lacquers for example. It is useful to individuals involved in study, development, and processing of metals and metallic compounds. It is invaluable for readers from the college level to industrial R & D and full-scale device fabrication, testing and sales. Scientific disciplines, work areas and individuals with great interest include: chemistry, physics, metallurgy, geology, solid state, ceramic and glass, research libraries, individuals dealing with chemical processing of inorganic materials, societies and schools.
Download or read book Chemical Abstracts written by and published by . This book was released on 2002 with total page 2626 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Fundamentals of Microfabrication and Nanotechnology Three Volume Set written by Marc J. Madou and published by CRC Press. This book was released on 2018-12-14 with total page 3654 pages. Available in PDF, EPUB and Kindle. Book excerpt: Now in its third edition, Fundamentals of Microfabrication and Nanotechnology continues to provide the most complete MEMS coverage available. Thoroughly revised and updated the new edition of this perennial bestseller has been expanded to three volumes, reflecting the substantial growth of this field. It includes a wealth of theoretical and practical information on nanotechnology and NEMS and offers background and comprehensive information on materials, processes, and manufacturing options. The first volume offers a rigorous theoretical treatment of micro- and nanosciences, and includes sections on solid-state physics, quantum mechanics, crystallography, and fluidics. The second volume presents a very large set of manufacturing techniques for micro- and nanofabrication and covers different forms of lithography, material removal processes, and additive technologies. The third volume focuses on manufacturing techniques and applications of Bio-MEMS and Bio-NEMS. Illustrated in color throughout, this seminal work is a cogent instructional text, providing classroom and self-learners with worked-out examples and end-of-chapter problems. The author characterizes and defines major research areas and illustrates them with examples pulled from the most recent literature and from his own work.
Download or read book Dry Etching Technology for Semiconductors written by Kazuo Nojiri and published by Springer. This book was released on 2014-10-25 with total page 126 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book is a must-have reference to dry etching technology for semiconductors, which will enable engineers to develop new etching processes for further miniaturization and integration of semiconductor integrated circuits. The author describes the device manufacturing flow, and explains in which part of the flow dry etching is actually used. The content is designed as a practical guide for engineers working at chip makers, equipment suppliers and materials suppliers, and university students studying plasma, focusing on the topics they need most, such as detailed etching processes for each material (Si, SiO2, Metal etc) used in semiconductor devices, etching equipment used in manufacturing fabs, explanation of why a particular plasma source and gas chemistry are used for the etching of each material, and how to develop etching processes. The latest, key technologies are also described, such as 3D IC Etching, Dual Damascene Etching, Low-k Etching, Hi-k/Metal Gate Etching, FinFET Etching, Double Patterning etc.
Download or read book Fundamentals of Microfabrication written by Marc J. Madou and published by CRC Press. This book was released on 2018-10-08 with total page 764 pages. Available in PDF, EPUB and Kindle. Book excerpt: MEMS technology and applications have grown at a tremendous pace, while structural dimensions have grown smaller and smaller, reaching down even to the molecular level. With this movement have come new types of applications and rapid advances in the technologies and techniques needed to fabricate the increasingly miniature devices that are literally changing our world. A bestseller in its first edition, Fundamentals of Microfabrication, Second Edition reflects the many developments in methods, materials, and applications that have emerged recently. Renowned author Marc Madou has added exercise sets to each chapter, thus answering the need for a textbook in this field. Fundamentals of Microfabrication, Second Edition offers unique, in-depth coverage of the science of miniaturization, its methods, and materials. From the fundamentals of lithography through bonding and packaging to quantum structures and molecular engineering, it provides the background, tools, and directions you need to confidently choose fabrication methods and materials for a particular miniaturization problem. New in the Second Edition Revised chapters that reflect the many recent advances in the field Updated and enhanced discussions of topics including DNA arrays, microfluidics, micromolding techniques, and nanotechnology In-depth coverage of bio-MEMs, RF-MEMs, high-temperature, and optical MEMs. Many more links to the Web Problem sets in each chapter
Download or read book Atomic Layer Deposition for Semiconductors written by Cheol Seong Hwang and published by Springer Science & Business Media. This book was released on 2013-10-18 with total page 266 pages. Available in PDF, EPUB and Kindle. Book excerpt: Offering thorough coverage of atomic layer deposition (ALD), this book moves from basic chemistry of ALD and modeling of processes to examine ALD in memory, logic devices and machines. Reviews history, operating principles and ALD processes for each device.
Download or read book Plasma Processing of Materials written by National Research Council and published by National Academies Press. This book was released on 1991-02-01 with total page 88 pages. Available in PDF, EPUB and Kindle. Book excerpt: Plasma processing of materials is a critical technology to several of the largest manufacturing industries in the worldâ€"electronics, aerospace, automotive, steel, biomedical, and toxic waste management. This book describes the relationship between plasma processes and the many industrial applications, examines in detail plasma processing in the electronics industry, highlights the scientific foundation underlying this technology, and discusses education issues in this multidisciplinary field. The committee recommends a coordinated, focused, and well-funded research program in this area that involves the university, federal laboratory, and industrial sectors of the community. It also points out that because plasma processing is an integral part of the infrastructure of so many American industries, it is important for both the economy and the national security that America maintain a strong leadership role in this technology.
Download or read book Scientific and Technical Aerospace Reports written by and published by . This book was released on 1978 with total page 1008 pages. Available in PDF, EPUB and Kindle. Book excerpt: Lists citations with abstracts for aerospace related reports obtained from world wide sources and announces documents that have recently been entered into the NASA Scientific and Technical Information Database.
Download or read book Research Opportunities in Corrosion Science and Engineering written by National Research Council and published by National Academies Press. This book was released on 2011-01-27 with total page 192 pages. Available in PDF, EPUB and Kindle. Book excerpt: The field of corrosion science and engineering is on the threshold of important advances. Advances in lifetime prediction and technological solutions, as enabled by the convergence of experimental and computational length and timescales and powerful new modeling techniques, are allowing the development of rigorous, mechanistically based models from observations and physical laws. Despite considerable progress in the integration of materials by design into engineering development of products, corrosion considerations are typically missing from such constructs. Similarly, condition monitoring and remaining life prediction (prognosis) do not at present incorporate corrosion factors. Great opportunities exist to use the framework of these materials design and engineering tools to stimulate corrosion research and development to achieve quantitative life prediction, to incorporate state-of-the-art sensing approaches into experimentation and materials architectures, and to introduce environmental degradation factors into these capabilities. Research Opportunities in Corrosion Science and Engineering identifies grand challenges for the corrosion research community, highlights research opportunities in corrosion science and engineering, and posits a national strategy for corrosion research. It is a logical and necessary complement to the recently published book, Assessment of Corrosion Education, which emphasized that technical education must be supported by academic, industrial, and government research. Although the present report focuses on the government role, this emphasis does not diminish the role of industry or academia.
Download or read book Semiconductor Laser Engineering Reliability and Diagnostics written by Peter W. Epperlein and published by John Wiley & Sons. This book was released on 2013-01-25 with total page 522 pages. Available in PDF, EPUB and Kindle. Book excerpt: This reference book provides a fully integrated novel approach to the development of high-power, single-transverse mode, edge-emitting diode lasers by addressing the complementary topics of device engineering, reliability engineering and device diagnostics in the same book, and thus closes the gap in the current book literature. Diode laser fundamentals are discussed, followed by an elaborate discussion of problem-oriented design guidelines and techniques, and by a systematic treatment of the origins of laser degradation and a thorough exploration of the engineering means to enhance the optical strength of the laser. Stability criteria of critical laser characteristics and key laser robustness factors are discussed along with clear design considerations in the context of reliability engineering approaches and models, and typical programs for reliability tests and laser product qualifications. Novel, advanced diagnostic methods are reviewed to discuss, for the first time in detail in book literature, performance- and reliability-impacting factors such as temperature, stress and material instabilities. Further key features include: practical design guidelines that consider also reliability related effects, key laser robustness factors, basic laser fabrication and packaging issues; detailed discussion of diagnostic investigations of diode lasers, the fundamentals of the applied approaches and techniques, many of them pioneered by the author to be fit-for-purpose and novel in the application; systematic insight into laser degradation modes such as catastrophic optical damage, and a wide range of technologies to increase the optical strength of diode lasers; coverage of basic concepts and techniques of laser reliability engineering with details on a standard commercial high power laser reliability test program. Semiconductor Laser Engineering, Reliability and Diagnostics reflects the extensive expertise of the author in the diode laser field both as a top scientific researcher as well as a key developer of high-power highly reliable devices. With invaluable practical advice, this new reference book is suited to practising researchers in diode laser technologies, and to postgraduate engineering students.
Download or read book Ceramic Abstracts written by and published by . This book was released on 1997 with total page 504 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Chemical Solution Synthesis for Materials Design and Thin Film Device Applications written by Soumen Das and published by Elsevier. This book was released on 2021-01-29 with total page 746 pages. Available in PDF, EPUB and Kindle. Book excerpt: Chemical Solution Synthesis for Materials Design and Thin Film Device Applications presents current research on wet chemical techniques for thin-film based devices. Sections cover the quality of thin films, types of common films used in devices, various thermodynamic properties, thin film patterning, device configuration and applications. As a whole, these topics create a roadmap for developing new materials and incorporating the results in device fabrication. This book is suitable for graduate, undergraduate, doctoral students, and researchers looking for quick guidance on material synthesis and device fabrication through wet chemical routes. Provides the different wet chemical routes for materials synthesis, along with the most relevant thin film structured materials for device applications Discusses patterning and solution processing of inorganic thin films, along with solvent-based processing techniques Includes an overview of key processes and methods in thin film synthesis, processing and device fabrication, such as nucleation, lithography and solution processing
Download or read book Molecular Sensors and Nanodevices written by John X. J. Zhang and published by Academic Press. This book was released on 2018-11-19 with total page 606 pages. Available in PDF, EPUB and Kindle. Book excerpt: Molecular Sensors and Nanodevices: Principles, Designs and Applications in Biomedical Engineering, Second Edition is designed to be used as a foundational text, aimed at graduates, advanced undergraduates, early-career engineers and clinicians. The book presents the essential principles of molecular sensors, including theories, fabrication techniques and reviews. In addition, important devices and recently, highly-cited research outcomes are also cited. This differentiates the book from other titles on the market whose primary focus is more research-oriented and aimed at more of a niche market. Covers the fundamental principles of device engineering and molecular sensing, sensor theories and applications in biomedical science and engineering Introduces nano/micro fabrication techniques, including MEMS, bioMEMS, microTAS and nanomaterials science that are essential in the miniaturization of versatile molecular sensors Explores applications of nanomaterials and biomaterials, including proteins, DNAs, nanoparticles, quantum dots, nanotubes/wires and graphene in biomedicine
Download or read book Physics Briefs written by and published by . This book was released on 1987 with total page 862 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Power GaN Devices written by Matteo Meneghini and published by Springer. This book was released on 2016-09-08 with total page 383 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book presents the first comprehensive overview of the properties and fabrication methods of GaN-based power transistors, with contributions from the most active research groups in the field. It describes how gallium nitride has emerged as an excellent material for the fabrication of power transistors; thanks to the high energy gap, high breakdown field, and saturation velocity of GaN, these devices can reach breakdown voltages beyond the kV range, and very high switching frequencies, thus being suitable for application in power conversion systems. Based on GaN, switching-mode power converters with efficiency in excess of 99 % have been already demonstrated, thus clearing the way for massive adoption of GaN transistors in the power conversion market. This is expected to have important advantages at both the environmental and economic level, since power conversion losses account for 10 % of global electricity consumption. The first part of the book describes the properties and advantages of gallium nitride compared to conventional semiconductor materials. The second part of the book describes the techniques used for device fabrication, and the methods for GaN-on-Silicon mass production. Specific attention is paid to the three most advanced device structures: lateral transistors, vertical power devices, and nanowire-based HEMTs. Other relevant topics covered by the book are the strategies for normally-off operation, and the problems related to device reliability. The last chapter reviews the switching characteristics of GaN HEMTs based on a systems level approach. This book is a unique reference for people working in the materials, device and power electronics fields; it provides interdisciplinary information on material growth, device fabrication, reliability issues and circuit-level switching investigation.
Download or read book Etching of III V Semiconductors written by Peter H. L. Notten and published by Elsevier Science & Technology. This book was released on 1991 with total page 376 pages. Available in PDF, EPUB and Kindle. Book excerpt:
