Download or read book Effect of Fuel Composition and Differential Diffusion on Flame Stabilization in Reacting Syngas Jets in Turbulent Cross flow written by and published by . This book was released on 2015 with total page 11 pages. Available in PDF, EPUB and Kindle. Book excerpt: Here, three-dimensional direct numerical simulation results of a transverse syngas fuel jet in turbulent cross-flow of air are analyzed to study the influence of varying volume fractions of CO relative to H2 in the fuel composition on the near field flame stabilization. The mean flame stabilizes at a similar location for CO-lean and CO-rich cases despite the trend suggested by their laminar flame speed, which is higher for the CO-lean condition. To identify local mixtures having favorable mixture conditions for flame stabilization, explosive zones are defined using a chemical explosive mode timescale. The explosive zones related to flame stabilization are located in relatively low velocity regions. The explosive zones are characterized by excess hydrogen transported solely by differential diffusion, in the absence of intense turbulent mixing or scalar dissipation rate. The conditional averages show that differential diffusion is negatively correlated with turbulent mixing. Moreover, the local turbulent Reynolds number is insufficient to estimate the magnitude of the differential diffusion effect. Alternatively, the Karlovitz number provides a better indicator of the importance of differential diffusion. A comparison of the variations of differential diffusion, turbulent mixing, heat release rate and probability of encountering explosive zones demonstrates that differential diffusion predominantly plays an important role for mixture preparation and initiation of chemical reactions, closely followed by intense chemical reactions sustained by sufficient downstream turbulent mixing. The mechanism by which differential diffusion contributes to mixture preparation is investigated using the Takeno Flame Index. The mean Flame Index, based on the combined fuel species, shows that the overall extent of premixing is not intense in the upstream regions. However, the Flame Index computed based on individual contribution of H2 or CO species reveals that hydrogen contributes significantly to premixing, particularly in explosive zones in the upstream leeward region, i.e. at the preferred flame stabilization location. Therefore, a small amount of H2 diffuses much faster than CO, creating relatively homogeneous mixture pockets depending on the competition with turbulent mixing. These pockets, together with high H2 reactivity, contribute to stabilizing the flame at a consistent location regardless of the CO concentration in the fuel for the present range of DNS conditions.

Download or read book Effect of Differential Diffusion on Flame Stabilization in a Syngas Jet in Turbulent Cross flow written by and published by . This book was released on 2015 with total page 2 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Advanced Turbulent Combustion Physics and Applications written by N. Swaminathan and published by Cambridge University Press. This book was released on 2022-01-06 with total page 485 pages. Available in PDF, EPUB and Kindle. Book excerpt: Explore a thorough overview of the current knowledge, developments and outstanding challenges in turbulent combustion and application.

Download or read book The Effects of Differential Diffusion in Counter flow Premixed Flames with Dilution and Enrichment written by Ehsan Abbasi Atibeh and published by . This book was released on 2019 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: "The continued combustion of fossil fuels to fulfill global energy demand is being questioned because of the well-known problem of greenhouse-gas (GHG) emissions, which introduces new carbon, in the form of carbon dioxide, into the environment causing climate change. However, the inherent advantages of combustion-based engines, e.g., energy and power densities, make it hard for other power systems to compete; hence, a leading strategy is to avoid burning fossil fuels by using alternative renewable fuels, such as hydrogen and renewable biofuels. Adaptability with alternative renewable fuels that have variable compositions is referred to as fuel flexibility, which is an important parameter of next-generation combustor design. However, fuel flexibility significantly affects combustor operability properties, such as blowout, flashback, and dynamic stability, mainly due to variations in turbulent burning rates. Changing the fuel and oxidizing-gas mixture composition affects flame characteristics and burning rates through changing: (1) mixture reactivity, which is represented by unstretched laminar flame speed, and (2) mixture diffusivity, i.e., the diffusivity of the deficient reactant and diffusivity of heat. The disparity between thermal and mass diffusivities at the flame front is known as "differential diffusion", which causes stretch sensitivity, and thermal-diffusive instabilities, in flame-front propagation, and is represented by Lewis number, a ratio of thermal-to-mass diffusivities.This thesis investigates the effects of differential diffusion and stretch sensitivity on propagation, stabilization, and structure of lean turbulent premixed flames in the thin reaction zone regime. In the context of fuel flexibility, various fuels and oxidizer-inert mixtures are used to form mixtures with distinct effective Lewis numbers, through changing both fuel diffusivity and thermal diffusivity of the mixture. In these experiments, the unstretched laminar flame speed is kept constant during mixture dilution, and hydrogen enrichment of hydrocarbon flames, through changing the mixture equivalence ratio, in order to minimize the effects of chemistry. Furthermore, bulk-flow properties and the temperature boundary condition are kept constant; hence, the study highlights the effects of differential diffusion. The experiments are carried out using strained counter-flow flames, in order to study the effects of both components of the flame stretch, i.e., hydrodynamic strain and curvature. Local instantaneous statistics of various flame parameters within the imaged plane are quantified using high-speed particle image velocimetry (PIV) and Mie scattering flame tomography at various levels of turbulence intensity. These statistics include flame location, flame velocity, and flame-front topology, such as flame stretch, flame-front curvature, and flame surface area.The statistics of various parameters of turbulent flames with distinct effective Lewis number show that the effects of differential diffusion on the burning rates and the structure of turbulent premixed flames are important in highly turbulent flames in the thin reaction zone of combustion. Furthermore, these results are not dependent on the fuel or oxidizing-gas mixture and can be described fully by the effective Lewis number and turbulence intensity. In addition, at constant turbulence intensities, differential diffusion increases the burning rate of turbulent flames in thermo-diffusively unstable mixtures through two main mechanisms: (1) increasing the local flamelet displacement velocity, and (2) increasing the flame surface area. This thesis shows the need to advance the combustion theory to produce models that can capture the effects of differential diffusion for flames in real-world combustion systems, in order to predict the performance of future fuel-flexible combustors. The experimental results of this thesis provide a valuable dataset for the validation of such theories." --

Download or read book Sustainability in Biofuel Production Technology written by Pratibha S. Agrawal and published by John Wiley & Sons. This book was released on 2022-08-26 with total page 372 pages. Available in PDF, EPUB and Kindle. Book excerpt: Sustainability in Biofuel Production Technology Explore current challenges and the latest technologies in biofuel production In Sustainability in Biofuel Production Technology, a team of engineers and chemists delivers a thorough and accessible exploration of the source of renewable energy biofuels poised to help conserve natural resources and limit the impact of fossil fuel use. The book offers detailed information about the challenges and trends in biodiesel production and includes contributions from leading researchers in the field of biodiesel production. Readers will explore aviation biofuels, biofuel production technologies, reactor design and safety considerations, and the modelling and simulation of biofuel production as they move through the book’s 14 chapters. The authors also analyze the performance of biofuels along with cost estimations and mathematical modeling of various process parameters. Readers will also find: A thorough introduction to biofuels, including their history, generation, classification, and relevant technologies In-depth presentations of the production technologies of biofuels, including chemical and biological production processes Comprehensive explorations of the utilization of biofuels in aviation, including performance analyses and safety considerations Fulsome discussions of key issues and challenges in biofuels production pathways and the environmental effects of biofuels Perfect for academic researchers and industrial scientists working in the biofuels, bioenergy, catalysis, and materials science sectors, Sustainability in Biofuel Production Technology will also be suitable for members of regulatory bodies in the bioenergy sector.

Download or read book The Effect of Pressure and Fuel Structure on the Soot Yield of a Turbulent Diffusion Flame in a Crossflow written by Bruce Tobis and published by . This book was released on 1983 with total page 170 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Impact of Fuel and Oxidizer Composition on Premixed Flame Stabilization in Turbulent Swirling Flows written by Soufien Taamallah and published by . This book was released on 2016 with total page 214 pages. Available in PDF, EPUB and Kindle. Book excerpt: The world relies on fossil fuels as its main energy source (86.7% in 1973, 81.7% in 2012). Several factors including the abundance of resources and the existing infrastructure suggest that this is likely to continue in the near future (potentially 75% in 2040). Meanwhile climate change continues to be a pressing concern that calls for the development of low CO2 energy systems. Among the most promising approaches are pre-combustion capture technologies, e.g., coal gasification and natural gas reforming that produce hydrogen-rich fuels. Another approach is oxy-combustion in which air is replaced by a mixture of O2/CO2/H2O as the oxidizer stream. However, modern gas turbines have been optimized to operate on methane-air combustion and several challenges, notably thermo-acoustic instability, arise when using other fuels or oxidizers because of their different thermochemical and transport properties. While these phenomena constitute a major challenge under conventional operations, using hydrogen-rich fuels or CO2-rich oxidizer exacerbates the problem by modifying the combustor stability map in ways that are not well understood. In this thesis, we identify combustion modes most prone to dynamics, predict the onset of thermo-acoustic instability over a wide range of fuel and oxidizer compositions, and define parameters that can scale the data. To this end, a combination of experimental and numerical tools were deployed. We carried out a series of experiments in an optically accessible laboratory-scale swirl-stabilized combustor typical of those found in modern gas turbines, using high-speed chemiluminescence to examine the flame macrostructure; high-speed Particle Image Velocimetry and OH Planar Laser Induced Fluorescence to probe the flow and flame microstructure. Numerical simulations were used to complement experiments and examine the complex three-dimensional two-way interaction between the flame and the turbulent swirling flow. Experimental data were used to construct the stability maps for different CH4-H2 mixtures and analyze the dynamic flame macrostructures and their transitions. A comparison with acoustically uncoupled combustion shows that the onset of thermo-acoustic instability is concomitant with a specific transition associated with the intermittent appearance of the flame in the outer recirculation zone (ORZ) and stabilization along the outer shear layer (forming between the swirling jet and the ORZ, as revealed by the PIV-PLIF data). The sudden onset of large amplitude limit cycle oscillations and the observed hysteresis suggest the existence of a sub-critical Hopf bifurcation typically characterized by a bistable or "triggering" zone; the flame intermittency in the ORZ can potentially provide the disturbance required to trigger these oscillations. Using a dual-camera method to track chemiluminescence in space and time, this flame transition was found to originate from a reacting kernel that detaches from the inner shear layer flame (forming between the jet and the vortex breakdown zone), reaching the ORZ and spinning at a specific frequency; its characteristic Strouhal number is independent of the Reynolds number and the fuel/oxidizer, only a function of the swirl strength. We propose a new Karlovitz number based criterion that defines the transition on a flow time - flame time space, the former being the inverse of the spinning frequency and the latter being the flame extinction strain rate. According to this scaling, the flame survives in the ORZ if and when it can overcome the region's bulk strain rate. This criterion is valid over a wide range of operating, fuel and oxidizer composition, covering a wide range of fast to slow chemistry scenarios. Given the role of this flame transition in triggering the instability, the same criterion is applicable to predicting the onset of thermo-acoustics. The interaction of the turbulent swirling flow with the flame is further examined using large eddy simulations. Numerical simulations show that the experimentally observed large scale flame structures along the inner shear layer are due to a helical vortex core that originates at the swirler's centerbody. This vortical structure stays aligned with the centerline in the combustor upstream section, but bends and reaches the inner shear layer-stabilized flame around the sudden expansion where it causes the flame wrinkling. We propose that the flame kernel igniting the ORZ/ OSL observed in the experiment may be related to the interaction between the helical vortical structure and the outer shear layer.

Download or read book Propagation and Extinction Studies of Laminar Lean Premixed Syngas Air Flames written by Yang Zhang and published by Springer. This book was released on 2017-07-18 with total page 142 pages. Available in PDF, EPUB and Kindle. Book excerpt: This thesis presents pioneering experimental and numerical studies on three aspects of the combustion characteristics of lean premixed syngas/air flames, namely the laminar flame speed, extinction limit and flammability limit. It illustrates a new extinction exponent concept, which enriches the combustion theory. Above all, the book provides the following: a) a series of carefully measured data and theoretical analyses to reveal the intrinsic mechanisms of the fuel composition effect on the propagation and extinction of lean syngas/air flames; b) a mixing model and correlation to predict the laminar flame speed of multi-component syngas fuels, intended for engineering computations; c) a new “extinction exponent” concept to describe the critical effects of chemical kinetics on the extinction of lean premixed syngas/air flames; and d) the effects and mechanism of the dilution of incombustible components on lean premixed syngas/air flames and the preferential importance among the thermal, chemical and diffusion effects.

Download or read book Turbulent Premixed Flames written by Nedunchezhian Swaminathan and published by Cambridge University Press. This book was released on 2011-04-25 with total page 447 pages. Available in PDF, EPUB and Kindle. Book excerpt: A work on turbulent premixed combustion is important because of increased concern about the environmental impact of combustion and the search for new combustion concepts and technologies. An improved understanding of lean fuel turbulent premixed flames must play a central role in the fundamental science of these new concepts. Lean premixed flames have the potential to offer ultra-low emission levels, but they are notoriously susceptible to combustion oscillations. Thus, sophisticated control measures are inevitably required. The editors' intent is to set out the modeling aspects in the field of turbulent premixed combustion. Good progress has been made on this topic, and this cohesive volume contains contributions from international experts on various subtopics of the lean premixed flame problem.

Download or read book And Effect of Differen al Diffusion on Flame Stabiliza on in a Syngas Jet in Turbulent Cross flow written by and published by . This book was released on 2015 with total page 18 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Experimental Studies on Flow Field and Flame Stabilization of a Premixed Reacting Jet in Vitiated Crossflow written by Jason Allen Wagner and published by . This book was released on 2016 with total page 312 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Flame and Emissions Characteristics of a High pressure Reacting Jet in Vitiated Crossflow written by Michelle Otero and published by . This book was released on 2020 with total page 109 pages. Available in PDF, EPUB and Kindle. Book excerpt: The goal of this work was to provide more insight in the jet in crossflow interaction at relevant operating conditions found in a gas turbine. The first part of this work focus on understanding the influence of pressure on the jet in crossflow mechanism as well as and the effect on NOx levels. Jet conditions such equivalence ratio and momentum flux ratios were held constant throughout the study with the pressure of the system ranging from 1atm to 5atm. The flow structure and flame stabilization of the jets at different pressures were characterized using particle image velocimetry (PIV) and CH* chemiluminescence.

Download or read book Investigation of Differential Diffusion Effects in Turbulent Hydrogen Jet Flame Using Conditional Moment Closure Method written by Man Ching Ma and published by . This book was released on 2014 with total page 148 pages. Available in PDF, EPUB and Kindle. Book excerpt: The effects of differential diffusion in the numerical modelling of a turbulent non-premixed hydrogen-air jet flame using a Conditional Moment Closure (CMC) method are investigated. The CMC calculations, which are coupled with computational fluid dynamics (CFD) calculations, relax the commonly used assumption of equal species mass diffusivities. The focus is on the predictions of species mass fractions and temperatures, especially the production of NO. The results of the calculations are compared with available experimental measurements. The formulation of the CMC species transport equation including differential diffusion is presented and the closure of the terms are discussed. Further, the CMC equation for conditional enthalpy is also derived in the present study. The implementation of the CMC equations using two dimensional finite volume method is discussed, including a presentation of the discretised forms of the equations. The results of the CMC calculations including the effects of differential diffusion show that NO mass fractions are increased from the large underpredictions observed for equal diffusivity results near the jet nozzle. Improvements are also found for other species such as H2 and H2O. The results show physical behaviours, such as a shift in the location of the reaction zone and increased reaction rates due to increased diffusion rates of H2. It is also found that differential diffusion effects persist downstream from the nozzle, where the effects are expected to be small, and reasons for the discrepancies are discussed in the present study. The profiles obtained from the CMC calculations show large radial variations, much larger than in equal diffusivity calculations. An analysis isolating the differential diffusion effects of various species shows that the largest changes occur due to the accounting for the differential diffusivity of H2. A budget of the terms in the CMC equations for the differentially diffusing chemical species and enthalpy is also investigated.

Download or read book Stabilization and Dynamic of Premixed Swirling Flames written by Paul Palies and published by Academic Press. This book was released on 2020-07-03 with total page 402 pages. Available in PDF, EPUB and Kindle. Book excerpt: Stabilization and Dynamic of Premixed Swirling Flames: Prevaporized, Stratified, Partially, and Fully Premixed Regimes focuses on swirling flames in various premixed modes (stratified, partially, fully, prevaporized) for the combustor, and development and design of current and future swirl-stabilized combustion systems. This includes predicting capabilities, modeling of turbulent combustion, liquid fuel modeling, and a complete overview of stabilization of these flames in aeroengines. The book also discusses the effects of the operating envelope on upstream fresh gases and the subsequent impact of flame speed, combustion, and mixing, the theoretical framework for flame stabilization, and fully lean premixed injector design. Specific attention is paid to ground gas turbine applications, and a comprehensive review of stabilization mechanisms for premixed, partially-premixed, and stratified premixed flames. The last chapter covers the design of a fully premixed injector for future jet engine applications. Features a complete view of the challenges at the intersection of swirling flame combustors, their requirements, and the physics of fluids at work Addresses the challenges of turbulent combustion modeling with numerical simulations Includes the presentation of the very latest numerical results and analyses of flashback, lean blowout, and combustion instabilities Covers the design of a fully premixed injector for future jet engine applications

Download or read book Burner Stabilities of Jet Diffusion Flames written by James Phillip Seaba and published by . This book was released on 1990 with total page 266 pages. Available in PDF, EPUB and Kindle. Book excerpt: The near field lift-off phenomena associated with jet diffusion flames were investigated. Lift-off is defined as the instant when the luminous flame zone detaches from the burner exit, stabilizing itself downstream. The lift-off of the jet diffusion flames were studied using a fuel jet centered in a large coflowing air annulus. Fuels used consisted of methane and propane. The fuels are diluted with nitrogen, argon, and helium. Annulus, diluted fuel, and external nozzle geometry effects are studied for the jet diffusion flame. The jet diffusion flame is sensitive to the annulus velocity, the lift-off velocity decreasing with increasing annular velocity. Lift-off velocity decreases as dilution concentrations of the fuel jet increase. The external geometry effects influence the lift-off velocity, especially at higher annular flow rates. Two theories have explained the lift-off of jet diffusion flames. The locally premixed theory which assumes that the fuel and oxidant are fully premixed prior to combustion. The lift-off of the flame zone occurs due to the convective velocity of the premixed reactants exceeding the local flame speed. The second theory, the laminar flamelet model, states that the diffusion of reactants into the flame zone exceeds the chemical reaction rate, causing the flame to extinguish at the flame base, lifting the flame from the nozzle to a position downstream. The two models were evaluated by the different lift-off velocities produced by annulus and diluent effects. Laser Doppler anemometry (LDA) was used to characterize the flow field at and near the base of the jet diffusion flame. The local straining rate across the flame was approximated by the gradient of the mean radial velocity in the radial direction for the pure and diluted methane conditions. The straining rate was in qualitative agreement with that reported in the literature for counter-flow methane diffusion flames near extinction.

Download or read book Experiments and Numerical Simulations of Turbulent Combustion of Diluted Sprays written by Bart Merci and published by Springer Science & Business Media. This book was released on 2014-03-27 with total page 167 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book reflects the results of the 2nd and 3rd International Workshops on Turbulent Spray Combustion. The focus is on progress in experiments and numerical simulations for two-phase flows, with emphasis on spray combustion. Knowledge of the dominant phenomena and their interactions allows development of predictive models and their use in combustor and gas turbine design. Experts and young researchers present the state-of-the-art results, report on the latest developments and exchange ideas in the areas of experiments, modelling and simulation of reactive multiphase flows. The first chapter reflects on flame structure, auto-ignition and atomization with reference to well-characterized burners, to be implemented by modellers with relative ease. The second chapter presents an overview of first simulation results on target test cases, developed at the occasion of the 1st International Workshop on Turbulent Spray Combustion. In the third chapter, evaporation rate modelling aspects are covered, while the fourth chapter deals with evaporation effects in the context of flamelet models. In chapter five, LES simulation results are discussed for variable fuel and mass loading. The final chapter discusses PDF modelling of turbulent spray combustion. In short, the contributions in this book are highly valuable for the research community in this field, providing in-depth insight into some of the many aspects of dilute turbulent spray combustion.

Download or read book Simulation of Flame Stabilization of Lifted Turbulent Jet Diffusion Flames written by Ming Chen and published by . This book was released on 2000 with total page 179 pages. Available in PDF, EPUB and Kindle. Book excerpt: