Download or read book Compressed Natural Gas Direct Injection Comparison Between Homogeneous and Stratified Combustion written by Shahrir Abdullah and published by . This book was released on 2017 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: Due to abundance of natural gas, the use of natural gas for automotive use, particularly for internal combustion engine (ICE), is more practical and cheaper than their future successors. Even though natural gas is a cleaner fuel than other fossil fuels and has a higher octane number and can lead to higher thermal efficiency, its low carbon number makes it less attractive as compared to gasoline and diesel. Based on its potential, an engine referred to as compressed natural gas direct injection engine (CNGDI) was designed, developed and tested to operate on compressed natural gas (CNG) as monofuel directly and centrally injected into the engine. Computational and experimental works have been performed to investigate the viability of the design. Computational fluid dynamics (CFD) simulations and experimental works with homogenous combustion showed that the results were in good agreement. From experimental works, it is found that combustion characteristics could be improved by using a stratified charge piston configuration with some drawback on performance. In terms of exhaust emissions, stratified configuration causes slight increase in the emission of CO, CO2 and NOx, which highlight a need for further study on this issue.

Download or read book Automotive Spark Ignited Direct Injection Gasoline Engines written by F. Zhao and published by Elsevier. This book was released on 2000-02-08 with total page 129 pages. Available in PDF, EPUB and Kindle. Book excerpt: The process of fuel injection, spray atomization and vaporization, charge cooling, mixture preparation and the control of in-cylinder air motion are all being actively researched and this work is reviewed in detail and analyzed. The new technologies such as high-pressure, common-rail, gasoline injection systems and swirl-atomizing gasoline fuel injections are discussed in detail, as these technologies, along with computer control capabilities, have enabled the current new examination of an old objective; the direct-injection, stratified-charge (DISC), gasoline engine. The prior work on DISC engines that is relevant to current GDI engine development is also reviewed and discussed. The fuel economy and emission data for actual engine configurations have been obtained and assembled for all of the available GDI literature, and are reviewed and discussed in detail. The types of GDI engines are arranged in four classifications of decreasing complexity, and the advantages and disadvantages of each class are noted and explained. Emphasis is placed upon consensus trends and conclusions that are evident when taken as a whole; thus the GDI researcher is informed regarding the degree to which engine volumetric efficiency and compression ratio can be increased under optimized conditions, and as to the extent to which unburned hydrocarbon (UBHC), NOx and particulate emissions can be minimized for specific combustion strategies. The critical area of GDI fuel injector deposits and the associated effect on spray geometry and engine performance degradation are reviewed, and important system guidelines for minimizing deposition rates and deposit effects are presented. The capabilities and limitations of emission control techniques and after treatment hardware are reviewed in depth, and a compilation and discussion of areas of consensus on attaining European, Japanese and North American emission standards presented. All known research, prototype and production GDI engines worldwide are reviewed as to performance, emissions and fuel economy advantages, and for areas requiring further development. The engine schematics, control diagrams and specifications are compiled, and the emission control strategies are illustrated and discussed. The influence of lean-NOx catalysts on the development of late-injection, stratified-charge GDI engines is reviewed, and the relative merits of lean-burn, homogeneous, direct-injection engines as an option requiring less control complexity are analyzed.

Download or read book Advances in Natural Gas Emerging Technologies written by Hamid Al-Megren and published by BoD – Books on Demand. This book was released on 2017-08-02 with total page 253 pages. Available in PDF, EPUB and Kindle. Book excerpt: Natural gas has become the world's primary supply of energy in the last decades. It is naturally occurring from the decomposition of organic materials, over the past 150 million years ago, into hydrocarbons. It is considered one of the most useful energy sources and the fastest growing energy source in the world. This book presents state-of-the-art advances in natural gas emerging technologies. It contains ten chapters divided into three sections that cover natural gas technology, utilization, and alternative.

Download or read book An Experimental Investigation of Direct Injection for Homogeneous and Fuel stratified Charge Compression Ignited Combustion Timing Control written by Craig David Marriott and published by . This book was released on 2001 with total page 664 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Natural Gas Engines written by Kalyan Kumar Srinivasan and published by Springer. This book was released on 2018-11-03 with total page 428 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book covers the various advanced reciprocating combustion engine technologies that utilize natural gas and alternative fuels for transportation and power generation applications. It is divided into three major sections consisting of both fundamental and applied technologies to identify (but not limited to) clean, high-efficiency opportunities with natural gas fueling that have been developed through experimental protocols, numerical and high-performance computational simulations, and zero-dimensional, multizone combustion simulations. Particular emphasis is placed on statutes to monitor fine particulate emissions from tailpipe of engines operating on natural gas and alternative fuels.

Download or read book Which Fuels for Low CO2 Engines written by Pierre Duret and published by Editions TECHNIP. This book was released on 2004 with total page 252 pages. Available in PDF, EPUB and Kindle. Book excerpt: Throughout the world, research and development in the field of vehicle transportation is increasingly focusing on engine and fuel combinations. The conventional and alternative fuels of the future are seen as fundamental to the development of a new generation of internal combustion engines that attain low well-to-wheel CO2 emissions along with near-zero pollutant emissions. These issues were debated during an international conference whose proceedings are presented in this book. This international conference attracted specialists in the field, including participants from universities, research centres and industry.Contents : Future of liquid fuels, Engine and fuel-related issues in HCCI & CAI combustion, Energy conversion in engines from natural gas, Use of hydrogen in IC engines, Which fuels for low CO2 engines?

Download or read book Advances in Natural Gas Technology written by Hamid Al-Megren and published by BoD – Books on Demand. This book was released on 2012-04-11 with total page 558 pages. Available in PDF, EPUB and Kindle. Book excerpt: Natural gas is a vital component of the world's supply of energy and an important source of many bulk chemicals and speciality chemicals. It is one of the cleanest, safest, and most useful of all energy sources, and helps to meet the world's rising demand for cleaner energy into the future. However, exploring, producing and bringing gas to the user or converting gas into desired chemicals is a systematical engineering project, and every step requires thorough understanding of gas and the surrounding environment. Any advances in the process link could make a step change in gas industry. There have been increasing efforts in gas industry in recent years. With state-of-the-art contributions by leading experts in the field, this book addressed the technology advances in natural gas industry.

Download or read book Automotive Gasoline Direct Injection Engines written by Fuquan Zhao and published by SAE International. This book was released on 2002-05-15 with total page 372 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book covers the latest global technical initiatives in the rapidly progressing area of gasoline direct injection (GDI), spark-ignited gasoline engines and examines the contribution of each process and sub-system to the efficiency of the overall system. Including discussions, data, and figures from many technical papers and proceedings that are not available in the English language, Automotive Gasoline Direct Injection Systems will prove to be an invaluable desk reference for any GDI subject or direct-injection subsystem that is being developed worldwide.

Download or read book Study of Ignition and Emissions in a Direct Injected Compression Ignition Natural Gas Engine written by Ivan Gogolev and published by . This book was released on 2016 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: Natural gas direct injection and glow plug ignition assist technologies were implemented in a single-cylinder, optically-accessible engine. Initial experiments studied the effects of injector and glow plug shield geometry on ignition quality. Injector and shield geometric effects were found to be significant, with only two of 20 tested geometric combinations resulting in reproducible combustion. Further experiments explored the effects of equivalence ratio and intake pressure on ignition delay, engine performance, and exhaust emissions. Combustion was found to proceed in a stratified-premixed mode at lower equivalence ratios, and a free-mixing mode at the higher equivalence ratios. Both combustion modes resulted in high NOx emissions. Stratified-premixed combustion produced higher hydrocarbon emissions, and lower levels of particulate matter and carbon monoxide, when compared to free-mixing combustion. Higher intake pressure was found to reduce all emissions levels. This effect was largely attributed to better charge mixing achieved from pressure-driven increase in engine swirl momentum.

Download or read book Emission Control and Fuel Economy written by John H Johnson and published by SAE International. This book was released on 2005-06-27 with total page 700 pages. Available in PDF, EPUB and Kindle. Book excerpt: Emission and fuel economy regulations and standards are compelling manufacturers to build ultra-low emission vehicles. As a result, engineers must develop spark-ignition engines with integrated emission control systems that use reformulated low-sulfur fuel. Emission Control and Fuel Economy for Port and Direct Injected SI Engines is a collection of SAE technical papers that covers the fundamentals of gasoline direct injection (DI) engine emissions and fuel economy, design variable effects on HC emissions, and advanced emission control technology and modeling approaches. All papers contained in this book were selected by an accomplished expert as the best in the field; reprinted in their entirety, they present a pathway to integrated emission control systems that meet 2004-2009 EPA standards for light-duty vehicles.

Download or read book Automotive Gasoline Direct Injection Engines written by Fuquan Zhao and published by SAE International. This book was released on 2002-05-15 with total page 372 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book covers the latest global technical initiatives in the rapidly progressing area of gasoline direct injection (GDI), spark-ignited gasoline engines and examines the contribution of each process and sub-system to the efficiency of the overall system. Including discussions, data, and figures from many technical papers and proceedings that are not available in the English language, Automotive Gasoline Direct Injection Systems will prove to be an invaluable desk reference for any GDI subject or direct-injection subsystem that is being developed worldwide.

Download or read book Design of Racing and High Performance Engines 1998 2003 written by Daniel J Holt and published by SAE International. This book was released on 2003-08-05 with total page 570 pages. Available in PDF, EPUB and Kindle. Book excerpt: The 53 technical papers in this book show the improvements and design techniques that researchers have applied to performance and racing engines. They provide an insight into what the engineers consider to be the top improvements needed to advance engine technology; and cover subjects such as: 1) Direct injection; 2) Valve spring advancements; 3) Turbocharging; 4) Variable valve control; 5) Combustion evaluation; and 5) New racing engines.

Download or read book Natural Gas and Renewable Methane for Powertrains written by Richard van Basshuysen and published by Springer. This book was released on 2016-02-04 with total page 491 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book focuses on natural gas and synthetic methane as contemporary and future energy sources. Following a historical overview, physical and chemical properties, occurrence, extraction, transportation and storage of natural gas are discussed. Sustainable production of natural gas and methane as well as production and storage of synthetic methane are scrutinized next. A substantial part of the book addresses construction of vehicles for natural and synthetic methane as well as large engines for industrial and maritime use. The last chapters present some perspectives on further uses of renewable liquid fuels as well as natural gas for industrial engines and gas power plants.

Download or read book Gasoline Engine Management written by Konrad Reif and published by Springer. This book was released on 2014-07-22 with total page 363 pages. Available in PDF, EPUB and Kindle. Book excerpt: The call for environmentally compatible and economical vehicles necessitates immense efforts to develop innovative engine concepts. Technical concepts such as gasoline direct injection helped to save fuel up to 20 % and reduce CO2-emissions. Descriptions of the cylinder-charge control, fuel injection, ignition and catalytic emission-control systems provides comprehensive overview of today ́s gasoline engines. This book also describes emission-control systems and explains the diagnostic systems. The publication provides information on engine-management-systems and emission-control regulations.

Download or read book Encyclopedia of Automotive Engineering written by and published by John Wiley & Sons. This book was released on 2015-03-23 with total page 3888 pages. Available in PDF, EPUB and Kindle. Book excerpt: Erstmals eine umfassende und einheitliche Wissensbasis und Grundlage für weiterführende Studien und Forschung im Bereich der Automobiltechnik. Die Encyclopedia of Automotive Engineering ist die erste umfassende und einheitliche Wissensbasis dieses Fachgebiets und legt den Grundstein für weitere Studien und tiefgreifende Forschung. Weitreichende Querverweise und Suchfunktionen ermöglichen erstmals den zentralen Zugriff auf Detailinformationen zu bewährten Branchenstandards und -verfahren. Zusammenhängende Konzepte und Techniken aus Spezialbereichen lassen sich so einfacher verstehen. Neben traditionellen Themen des Fachgebiets beschäftigt sich diese Enzyklopädie auch mit "grünen" Technologien, dem Übergang von der Mechanik zur Elektronik und den Möglichkeiten zur Herstellung sicherer, effizienterer Fahrzeuge unter weltweit unterschiedlichen wirtschaftlichen Rahmenbedingungen. Das Referenzwerk behandelt neun Hauptbereiche: (1) Motoren: Grundlagen; (2) Motoren: Design; (3) Hybrid- und Elektroantriebe; (4) Getriebe- und Antriebssysteme; (5) Chassis-Systeme; (6) Elektrische und elektronische Systeme; (7) Karosserie-Design; (8) Materialien und Fertigung; (9) Telematik. - Zuverlässige Darstellung einer Vielzahl von Spezialthemen aus dem Bereich der Automobiltechnik. - Zugängliches Nachschlagewerk für Jungingenieure und Studenten, die die technologischen Grundlagen besser verstehen und ihre Kenntnisse erweitern möchten. - Wertvolle Verweise auf Detailinformationen und Forschungsergebnisse aus der technischen Literatur. - Entwickelt in Zusammenarbeit mit der FISITA, der Dachorganisation nationaler Automobil-Ingenieur-Verbände aus 37 Ländern und Vertretung von über 185.000 Ingenieuren aus der Branche. - Erhältlich als stets aktuelle Online-Ressource mit umfassenden Suchfunktionen oder als Print-Ausgabe in sechs Bänden mit über 4.000 Seiten. Ein wichtiges Nachschlagewerk für Bibliotheken und Informationszentren in der Industrie, bei Forschungs- und Schulungseinrichtungen, Fachgesellschaften, Regierungsbehörden und allen Ingenieurstudiengängen. Richtet sich an Fachingenieure und Techniker aus der Industrie, Studenten höherer Semester und Studienabsolventen, Forscher, Dozenten und Ausbilder, Branchenanalysen und Forscher.

Download or read book Advances in Compression Ignition Natural Gas Diesel Dual Fuel Engines written by Hongsheng Guo and published by Frontiers Media SA. This book was released on 2021-03-23 with total page 125 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Internal Combustion Engine Handbook written by Richard Van Basshuysen and published by SAE International. This book was released on 2016-03-07 with total page 1152 pages. Available in PDF, EPUB and Kindle. Book excerpt: More than 120 authors from science and industry have documented this essential resource for students, practitioners, and professionals. Comprehensively covering the development of the internal combustion engine (ICE), the information presented captures expert knowledge and serves as an essential resource that illustrates the latest level of knowledge about engine development. Particular attention is paid toward the most up-to-date theory and practice addressing thermodynamic principles, engine components, fuels, and emissions. Details and data cover classification and characteristics of reciprocating engines, along with fundamentals about diesel and spark ignition internal combustion engines, including insightful perspectives about the history, components, and complexities of the present-day and future IC engines. Chapter highlights include: • Classification of reciprocating engines • Friction and Lubrication • Power, efficiency, fuel consumption • Sensors, actuators, and electronics • Cooling and emissions • Hybrid drive systems Nearly 1,800 illustrations and more than 1,300 bibliographic references provide added value to this extensive study. “Although a large number of technical books deal with certain aspects of the internal combustion engine, there has been no publication until now that covers all of the major aspects of diesel and SI engines.” Dr.-Ing. E. h. Richard van Basshuysen and Professor Dr.-Ing. Fred Schäfer, the editors, “Internal Combustion Engines Handbook: Basics, Components, Systems, and Perpsectives”