Download or read book Broadband Direct RF Digitization Receivers written by Olivier Jamin and published by Springer Science & Business Media. This book was released on 2013-09-06 with total page 175 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book discusses the trade-offs involved in designing direct RF digitization receivers for the radio frequency and digital signal processing domains. A system-level framework is developed, quantifying the relevant impairments of the signal processing chain, through a comprehensive system-level analysis. Special focus is given to noise analysis (thermal noise, quantization noise, saturation noise, signal-dependent noise), broadband non-linear distortion analysis, including the impact of the sampling strategy (low-pass, band-pass), analysis of time-interleaved ADC channel mismatches, sampling clock purity and digital channel selection. The system-level framework described is applied to the design of a cable multi-channel RF direct digitization receiver. An optimum RF signal conditioning, and some algorithms (automatic gain control loop, RF front-end amplitude equalization control loop) are used to relax the requirements of a 2.7GHz 11-bit ADC. A two-chip implementation is presented, using BiCMOS and 65nm CMOS processes, together with the block and system-level measurement results. Readers will benefit from the techniques presented, which are highly competitive, both in terms of cost and RF performance, while drastically reducing power consumption.
Download or read book Signal Digitization and Reconstruction in Digital Radios written by Yefim Poberezhskiy and published by Artech House. This book was released on 2018-12-31 with total page 340 pages. Available in PDF, EPUB and Kindle. Book excerpt: This comprehensive resource provides the latest information on digitization and reconstruction (D&R) of analog signals in digital radios. Readers learn how to conduct comprehensive analysis, concisely describe the major signal processing procedures carried out in the radios, and demonstrate the dependence of these procedures on the quality of D&R. The book presents and analyzes the most promising and theoretically sound ways to improve the characteristics of D&R circuits and illustrate the influence of these improvements on the capabilities of digital radios. The book is intended to bridge the gap that exists between theorists and practical engineers developing D&R techniques by introducing new signal transmission and reception methods that can effectively utilize the unique capabilities offered by novel digitization and reconstruction techniques.
Download or read book Intelligent Computing in Engineering written by Vijender Kumar Solanki and published by Springer Nature. This book was released on 2020-04-09 with total page 1159 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book comprises select papers from the international conference on Research in Intelligent and Computing in Engineering (RICE 2019) held at Hanoi University of Industry, Hanoi, Vietnam. The volume focuses on current research on various computing models such as centralized, distributed, cluster, grid and cloud. The contents cover recent advances in wireless sensor networks, mobile ad hoc networks, internet of things, machine learning, grid and cloud computing, and their various applications. The book will help researchers as well as professionals to gain insight into the rapidly evolving fields of internet computing and data mining.
Download or read book Digital Techniques for Wideband Receivers written by James B. Tsui and published by SciTech Publishing. This book was released on 2004-06-30 with total page 608 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book is a current, comprehensive design guide for your digital processing work with today's complex receiver systems. This book brings you up-to-date with the latest information on wideband electronic warfare receivers, the ADC testing procedure, frequency channelization and decoding schemes, and the operation of monobit receivers.
Download or read book Direct Conversion Receivers in Wide Band Systems written by Aarno Pärssinen and published by Springer Science & Business Media. This book was released on 2006-04-18 with total page 250 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book is based on my doctoral thesis at the Helsinki University of Technology. Several different projects during five years guided me from the basics of the RF IC design to the implementations of highly integrated radio receiver chips. Sharing time and effort between IC and system issues is not always straightforward. I have been lucky to follow both topics and share experiences with diligent and enthusiastic people having different specialities. As a result, this book will cover a wide range of different topics needed in the design of highly integrated radio receivers. Experiences from the first receiver prototypes for the third generation cellular systems form the basis of this book. Most of the issues are directly related to the early proposals of European and Japanese standardization organizations. For example, the chip rate was originally set to 4. 096 Mcps in a wide-band CDMA channel. I have kept that number in the book in most of the examples although it has been later changed to 3. 84 Mcps. I hope that the readers will accept that and the possible other incompabilities to the latest specifications. At least in the research phase the changes even in the most essential requirements are definitely not a rare incident and IC designers should be able to react and modify their designs as soon as they can.
Download or read book Software Defined Radio written by Walter H.W. Tuttlebee and published by John Wiley & Sons. This book was released on 2003-04-11 with total page 440 pages. Available in PDF, EPUB and Kindle. Book excerpt: Software defined radio (SDR) is one of the most important topics of research, and indeed development, in the area of mobile and personal communications. SDR is viewed as an enabler of global roaming and as a unique platform for the rapid introduction of new services into existing live networks. It therefore promises mobile communication networks a major increase in flexibility and capability. SDR brings together two key technologies of the last decade - digital radio and downloadable software. It encompasses not only reconfiguration of the air interface parameters of handset and basestation products but also the whole mobile network, to facilitate the dynamic introduction of new functionality and mass-customised applications to the user's terminal, post-purchase. This edited book, contributed by internationally respected researchers and industry practitioners, describes the current technological status of radio frequency design, data conversion, reconfigurable signal processing hardware, and software issues at all levels of the protocol stack and network. The book provides a holistic treatment of SDR addressing the full breadth of relevant technologies - radio frequency design, signal processing and software - at all levels. As such it provides a solid grounding for a new generation of wireless engineers for whom radio design in future will assume dynamic flexibility as a given. In particular it explores * The unique demands of SDR upon the RF subsystem and their implications for front end design methodologies * The recent concepts of the 'digital front end' and 'parametrization' * The role and key influence of data conversion technologies and devices within software radio, essential to robust product design * The evolution of signal processing technologies, describing new architectural approaches * Requirements and options for software download * Advances in 'soft' protocols and 'on-the-fly' software reconfiguration * Management of terminal reconfiguration and its network implications * The concepts of the waveform description language The book also includes coverage of * Potential breakthrough technologies, such as superconducting RSFQ technology and the possible future role of MEMS in RF circuitry * Competing approaches, eg all-software radios implemented on commodity computing vs advanced processing architectures that dynamically optimise their configuration to match the algorithm requirements at a point in time The book opens with an introductory chapter by Stephen Blust, Chair of the ITU-R WP8F Committee and Chair of the SDR Forum presenting a framework for SDR, in terms of definitions, evolutionary perspectives, introductory timescales and regulation. Suitable for today's engineers, technical staff and researchers within the wireless industry, the book will also appeal to marketing and commercial managers who need to understand the basics and potential of the technology for future product development. Its balance of industrial and academic contributors also makes it suitable as a text for graduate and post-graduate courses aiming to prepare the next generation of wireless engineers.
Download or read book Direct Sampling Receivers for Broadband Communications written by Jie Fang (Ph. D.) and published by . This book was released on 2018 with total page 200 pages. Available in PDF, EPUB and Kindle. Book excerpt: Today everything tends to be connected in the Internet of Things (IoT) universe, where a broad variety of communication standards and technologies are used for those connected devices. It is always a dream to design a Software-Defined Radio (SDR) supporting different standards solely based on the software configuration. As integrated-circuit (IC) manufacture and design advance, a partial of SDR can be realized. This thesis investigates one of the most important parts in a SDR: the analog design of a direct sampling (DS) receiver, which mainly consists of a broadband RF front end and a wideband ADC. Especially, a DS receiver shows a great flexibility and efficiency for the simultaneous reception of multiple channels comparing with the traditional parallelism of superheterodyne structure. The research contributions of this work include (1) demonstration and comparative analysis of two new architectures of broadband RFPGAs: voltage-mode: RFPGA-V and current-mode: RFPGA-I. RFPGA-V and RFPGA-I utilize an innovative interpolation method and current steering approach, respectively, to achieve a fine gain step of 0.25-dB over 40-dB gain range for several GHz frequency range. Besides, with innovative design, no off-chip inductor is needed for the both RFPGAs. (2) The design of a 5-GS/s 10b time-interleaved SAR. The ADC power efficiency is significantly improved by many design techniques: the low-energy CDAC switching scheme, optimized input common-mode voltage for comparator, optimal reduced radix-2 capacitor ratio for low-power reference buffers and higher conversion speed, etc. The lane-to-lane mismatches in a time-interleave ADC are minimized by using optimal floor plan and then are calibrated digitally. Three prototypes: the broadband RF front ends with RFPGA-V, the broadband RF front ends with RFPGA-I and a 5-GHz ADC, are fabricated to verify the proposed ideas in 28nm CMOS technology
Download or read book Digital Techniques for Wideband Receivers written by James Tsui and published by IET. This book was released on 2015-10-30 with total page 609 pages. Available in PDF, EPUB and Kindle. Book excerpt: Digital Techniques for Wideband Receivers is widely recognized as the definitive design guide on digital processing work with today's complex receiver systems. This third edition brings readers up-to-date with the latest information on wideband electronic warfare receivers, and includes new chapters on the detection of FM and BPSK radar signals, analog-to-information, time-reversal filter, monobit receivers with improved instantaneous dynamic range and it offers insights on building electronic warfare receivers. From fundamental concepts and procedures, to recent technology advances in digital receivers, readers get practical solutions to important wideband receiver problems. This book has been updated with many of the latest concepts to help users design receivers that are relevant for today's electronic warfare systems. It will be an ideal reference for defense digital signal processing engineers, in government and industry.
Download or read book Practical RF Circuit Design for Modern Wireless Systems written by Rowan Gilmore and published by Artech House. This book was released on 2003 with total page 594 pages. Available in PDF, EPUB and Kindle. Book excerpt: A practical approach to RF circuit design, this volume covers nonlinear circuits and modelling, RF transistor amplifiers, oscillators and mixers.
Download or read book Terahertz Devices Circuits and Systems written by Sudipta Das and published by Springer Nature. This book was released on 2022-09-26 with total page 304 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book is aimed to bring the emerging application aspects of THz technology and various modules used for its successful realization. It gathers scientific technological novelties and advancements already developed or under development in the academic and research communities. This book focuses on recent advances, different research issues in terahertz technology and would also seek out theoretical, methodological, well-established and validated empirical work dealing with these different topics. In particular, this textbook covers design considerations and current trends of THz antennas and antenna arrays to deal with the transmission and reception of THz EM waves. It also presents a discussion on metamaterial structures, meta-surfaces, and absorbers to be used for some kind of sensing and detection applications. Furthermore, it reports on THz wireless communication aspects, 6G network issues and challenges, advantages and disadvantages, generation and detection of THz waves, Signal and Communication Processing for THz communication, reconfigurable low-noise amplifier (LNA) design, III-Nitride HEMTs for THz Applications, photonic crystal fiber for sensing applications, THz Design Variable Estimation by Deep Optimization, and THz Imaging issues. Once the readers finish studying this book then they will learn about the importance of THz technology, advancement in the field, applications, THz modules like antennas, MIMO and DRAs, communication aspects, LNAs, generation of THz waves, etc and future scope. It also leads to enhancement in their knowledge in THz technology, gives a platform to future technology and novel applications realization.
Download or read book Broadband RF Front end Design for Multi standard Receiver with High linearity and Low noise Techniques written by Ju Sung Kim and published by . This book was released on 2012 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: Future wireless communication devices must support multiple standards and features on a single-chip. The trend towards software-defined radio requires flexible and efficient RF building blocks which justifies the adoption of broadband receiver front-ends in modern and future communication systems. The broadband receiver front-end significantly reduces cost, area, pins, and power, and can process several signal channels simultaneously. This research is mainly focused on the analysis and realization of the broadband receiver architecture and its various building blocks (LNA, Active Balun-LNA, Mixer, and trans-impedance amplifier) for multi-standard applications. In the design of the mobile DTV tuner, a direct-conversion receiver architecture is adopted achieving low power, low cost, and high dynamic-range for DVB-H standard. The tuner integrates a single-ended RF variable gain amplifier (RFVGA), a current-mode passive mixer, and a combination of continuous and discrete-time baseband filter with built-in anti-aliasing. The proposed RFVGA achieves high dynamic-range and gain-insensitive input impedance matching performance. The current-mode passive mixer achieves high gain, low noise, and high linearity with low power supplies. A wideband common-gate LNA is presented that overcomes the fundamental trade-off between power and noise match without compromising its stability. The proposed architecture can achieve the minimum noise figure over the previously reported feedback amplifiers in common-gate configuration. The proposed architecture achieves broadband impedance matching, low noise, large gain, enhanced linearity, and wide bandwidth concurrently by employing an efficient and reliable dual negative-feedback. For the wideband Inductorless Balun-LNA, active single-to-differential architecture has been proposed without using any passive inductor on-chip which occupies a lot of silicon area. The proposed Balun-LNA features lower power, wider bandwidth, and better gain and phase balance than previously reported architectures of the same kind. A surface acoustic wave (SAW)-less direct conversion receiver targeted for multistandard applications is proposed and fabricated with TSMC 0.13?m complementary metal-oxide-semiconductor (CMOS) technology. The target is to design a wideband SAW-less direct coversion receiver with a single low noise transconductor and current-mode passive mixer with trans-impedance amplifier utilizing feed-forward compensation. The innovations in the circuit and architecture improves the receiver dynamic range enabling highly linear direct-conversion CMOS front-end for a multi-standard receiver.
Download or read book The Wireless Internet of Things written by Daniel Chew and published by John Wiley & Sons. This book was released on 2018-10-10 with total page 203 pages. Available in PDF, EPUB and Kindle. Book excerpt: Provides a detailed analysis of the standards and technologies enabling applications for the wireless Internet of Things The Wireless Internet of Things: A Guide to the Lower Layers presents a practitioner’s perspective toward the Internet of Things (IoT) focusing on over-the-air interfaces used by applications such as home automation, sensor networks, smart grid, and healthcare. The author—a noted expert in the field—examines IoT as a protocol-stack detailing the physical layer of the wireless links, as both a radio and a modem, and the media access control (MAC) that enables communication in congested bands. Focusing on low-power wireless personal area networks (WPANs) the text outlines the physical and MAC layer standards used by ZigBee, Bluetooth LE, Z-Wave, and Thread. The text deconstructs these standards and provides background including relevant communication theory, modulation schemes, and access methods. The author includes a discussion on Wi-Fi and gateways, and explores their role in IoT. He introduces radio topologies used in software-defined radio implementations for the WPANs. The book also discusses channel modelling and link budget analysis for WPANs in IoT. This important text: Introduces IEEE 802.15.4, ITU-T G.9959, and Bluetooth LE as physical layer technology standards enabling wireless IoT Takes a layered approach in order to cultivate an appreciation for the various standards that enable interoperability Provides clarity on wireless standards with particular focus on actual implementation Written for IoT application and platform developers as well as digital signal processing, network, and wireless communication engineers; The Wireless Internet of Things: A Guide to the Lower Layersoffers an inclusive overview of the complex field of wireless IoT, exploring its beneficial applications that are proliferating in a variety of industries.
Download or read book Sigma Delta Converters Practical Design Guide written by Jose M. de la Rosa and published by John Wiley & Sons. This book was released on 2018-11-05 with total page 581 pages. Available in PDF, EPUB and Kindle. Book excerpt: Thoroughly revised and expanded to help readers systematically increase their knowledge and insight about Sigma-Delta Modulators Sigma-Delta Modulators (SDMs) have become one of the best choices for the implementation of analog/digital interfaces of electronic systems integrated in CMOS technologies. Compared to other kinds of Analog-to-Digital Converters (ADCs), Σ∆Ms cover one of the widest conversion regions of the resolution-versus-bandwidth plane, being the most efficient solution to digitize signals in an increasingly number of applications, which span from high-resolution low-bandwidth digital audio, sensor interfaces, and instrumentation, to ultra-low power biomedical systems and medium-resolution broadband wireless communications. Following the spirit of its first edition, Sigma-Delta Converters: Practical Design Guide, 2nd Edition takes a comprehensive look at SDMs, their diverse types of architectures, circuit techniques, analysis synthesis methods, and CAD tools, as well as their practical design considerations. It compiles and updates the current research reported on the topic, and explains the multiple trade-offs involved in the whole design flow of Sigma-Delta Modulators—from specifications to chip implementation and characterization. The book follows a top-down approach in order to provide readers with the necessary understanding about recent advances, trends, and challenges in state-of-the-art Σ∆Ms. It makes more emphasis on two key points, which were not treated so deeply in the first edition: It includes a more detailed explanation of Σ∆Ms implemented using Continuous-Time (CT) circuits, going from system-level synthesis to practical circuit limitations. It provides more practical case studies and applications, as well as a deeper description of the synthesis methodologies and CAD tools employed in the design of Σ∆ converters. Sigma-Delta Converters: Practical Design Guide, 2nd Edition serves as an excellent textbook for undergraduate and graduate students in electrical engineering as well as design engineers working on SD data-converters, who are looking for a uniform and self-contained reference in this hot topic. With this goal in mind, and based on the feedback received from readers, the contents have been revised and structured to make this new edition a unique monograph written in a didactical, pedagogical, and intuitive style.
Download or read book Circuit Techniques for Programmable Broadband Radio Receivers written by Travis Michael Forbes and published by . This book was released on 2014 with total page 314 pages. Available in PDF, EPUB and Kindle. Book excerpt: The functionality provided by mobile devices such as cellular phones and tablets continues to increase over the years, with integration of an ever larger number of wireless standards within a given device. In several of these designs, each standard supported by a device requires its own IC receiver to be mounted on the device's PCB. In multistandard and multimode radios, it is desirable to integrate all receivers onto the same IC as the digital processors for the standards, in order to reduce device cost and size. Ideally all the receivers should also share a single signal chain. Since each standard has its own requirements for linearity and noise figure, and each standard operates at a different RF carrier frequency, implementing such a receiver is very challenging. Such a receiver could be theoretically implemented using a broadband mixing receiver or by direct sampling by a high-speed analog-to-digital converter (ADC). Broadband mixing requires the use of a harmonic rejection mixer (HRM) or tunable band pass filter to remove harmonic mixing effects, which in the past have suffered from a large primary clock tuning range and high power consumption. However, direct sampling of the RF input requires a high-speed ADC with large dynamic range which is typically limited by clock timing skew, clock jitter, or harmonic folding. In this dissertation, techniques for programmable broadband radio receivers are proposed. A local oscillator (LO) synthesis method within HRMs is proposed which reduces the required primary clock tuning range in broadband receivers. The LO synthesis method is implemented in 130-nm CMOS. A clocking technique is introduced within the two-stage HRM, which helps in achieving state-of-the-art harmonic rejection performance without calibration or harmonic filtering. An analog frequency synthesis based broadband channelizer is proposed using the LO synthesis method which is capable of channelizing a broadband input using a single mixing stage and primary clock frequency. A frequency-folded ADC architecture is proposed which enables high-speed sampling with high dynamic range. A receiver based on the frequency-folded ADC architecture is implemented in 65-nm CMOS and achieves a sample rate of 2-GS/s, a mean 49-dB SNDR, and 8.5-dB NF.
Download or read book MRI from Picture to Proton written by Donald W. McRobbie and published by Cambridge University Press. This book was released on 2017-04-13 with total page 405 pages. Available in PDF, EPUB and Kindle. Book excerpt: This new edition includes the latest on quantitative MR, safety, multi-band excitation, Dixon imaging and MR elastography.
Download or read book Design of Analog CMOS Integrated Circuits written by Behzad Razavi and published by McGraw-Hill Higher Education. This book was released on 2016-01-22 with total page 801 pages. Available in PDF, EPUB and Kindle. Book excerpt: The CMOS technology are has quickly grown calling for a new text---and here it is covering the analysis and design of CMOS integrated circuits that practicing engineers need to master to succeed. Filled with many examples and chapter-ending problems the book not only describes the thought process behind each circuit topology but also considers the rationale behind each modification. The analysis and design techniques focus on CMOS circuits but also apply to other IC technologies.Design of Analog CMOS Integrated Circuits deals with the analysis and design of analog CMOS integrated circuits emphasizing recent technological developments and design paradigms that students and practicing engineers need to master to succeed in today's industry. Based on the author's teaching and research experience in the past ten years the text follows three general principles: (1) Motivate the reader by describing the significance and application of each idea with real-world problems; (2) Force the reader to look at concepts from an intuitive point of view preparing him/her for more complex problems; (3) Complement the intuition by rigorous analysis confirming the results obtained by the intuitive yet rough approach.
Download or read book Proceedings written by and published by . This book was released on 2000 with total page 486 pages. Available in PDF, EPUB and Kindle. Book excerpt:
