Download or read book Work Zone Speed Analysis Using Driving Simulator Data written by Arash Adeli and published by . This book was released on 2014 with total page 100 pages. Available in PDF, EPUB and Kindle. Book excerpt: This study investigates drivers' behavior in the highway work zone by incorporating virtual data collected by a high fidelity driving simulator. The study specifically examined speed variations along the work zone and compliance with the speed limit. A large network of 154 square miles southwest of Baltimore was developed in driving simulator. Over 100 participants from different socioeconomic groups were recruited to run driving tests under the study scenarios. Speed analysis was performed in both aggregate and disaggregate levels in work zone and in the areas under the influence of work zone related signs. The results demonstrate that drivers significantly comply with the speed limit in work zone and reduced their speed as they approached the work zone. Evaluation of speed limit violators confronting the work zone and its associated signs reveals that the majority of speed limit violators comply with the speed limit. Age, road familiarity and experience had a significant impact on speed limit compliance in the work zone while education level, income level and gender didn't reveal a clear association. Study results showed that although most of the drivers increased their speed immediately after passing the work zone, the compliance rate with the speed limit increased in comparison with the upstream zone, which demonstrate a sustainable effect of work zone and its associated signs on speed limit compliance behavior. The findings of this study could benefit transportation agencies for proper design of work zones and practice to increase safety for workers and drivers by predicting driver behavior in work zones. -- Abstract.
Download or read book Data Analysis for Driving Pattern Identification and Driver s Behavior Modeling in a Freeway Work Zone written by Hari Narayanan Vijaya Raghavan Nadathur and published by . This book was released on 2016 with total page 64 pages. Available in PDF, EPUB and Kindle. Book excerpt: "A variety of methods are used by Departments of Transportation (DOT) for informing drivers about upcoming work zones. One such method is work zone signage configuration. Signage plays an important role in work zones to provide guidance to drivers when conditions on the road vary from normal. Therefore, it is necessary to evaluate the effectiveness of different configurations, by law, before implementation of new signage designs that deviate from the national standards. The Manual on Uniform Traffic Control Devices (MUTCD) is a compilation of national standards for all traffic control devices, including road markings, highway signs, and traffic signals. In the present work which is funded by the Missouri Department of Transportation (MoDOT), the safety effect of an alternative merge sign configuration provided by MoDOT is investigated in a freeway work zone. This investigation is based on a simulation study that involves a total of 75 study participants representing an overall distribution of drivers in the state of Missouri. This simulation study required the participants to experience four work zone configurations on a driving simulator. Right merge and left merge scenarios were simulated for two work zone sign configurations, one being the national standard from MUTCD and the other being an alternate work zone sign configuration proposed by MoDOT. The objective of this study is to establish the effectiveness of both these configurations by data analyses. Results of the statistical analysis indicate that MUTCD left merge was significantly different than the driving patterns for the other three scenarios. There was significant difference between MUTCD left merge and MoDOT alternate left merge but no dramatic differences were observed for the right merge scenarios"--Abstract, page iii.
Download or read book Effects of Police Presence on Speed in a Highway Work Zone written by R. F. Benekohal and published by . This book was released on 1992 with total page 86 pages. Available in PDF, EPUB and Kindle. Book excerpt: This study evaluated the effects of police presence on the speed of vehicles in a work zone and determined the "halo" effects of police presence (lasting effects when police are gone) on vehicular speeds. A marked police car circulated in a 4-mile long interstate highway work zone and actively enforced the speed limit laws. Variables such as the average speed, speed distribution, percentage of fast-moving motorists, and net speed reductions for cars and trucks were used for evaluation. The results indicated that the average speeds of the cars and trucks were 4.3-4.4, and 4.3-5.0 mph, respectively, lower when police were patrolling the work zone compared to no-police patrol condition. The percentage of fast-moving cars and trucks before the work space decreased by 14% and 32%, respectively, when police were in the work zone. These speed reductions indicate that the police presence was effective in decreasing the speed of vehicles in the work zone. The police presence had halo effects on trucks but not on cars. Trucks traveled at reduced speed when police were present in the work zone and this trend of traveling at the reduced speed continued for a time period at least one hour after the police departed from the work zone. However, cars traveled 2. 4-3. o mph faster and the percentage of fast-moving cars in the work zone increased after the police left the area.
Download or read book Validation of Traffic Simulation Model Output for Work Zone and Mobile Source Emissions Modeling and Integration with Human in the loop Driving Simulators written by Shauna L. Hallmark and published by . This book was released on 2014 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: "The next generation motor vehicle emission rate model used in the US, the United States Environmental Protection Agency's Motor Vehicle Emmission Simulator (MOVES), requires second-by-second vehicle data in order to fully utilize model capabilities. However, field data collection of this type of data is resource intensive and frequently not realistic for local agencies. Some microsimulation models have the capability of outputting instantaneous speed and acceleration, which can be used in MOVES. With these capabilities, microsimulation offers a valuable tool to conduct analysis requiring a large number of data. ... Two case studies were used to assess the utility of the microsimulation model, Vissim, in developing output that can be used as input to MOVES. In one scenario, drivers were selected to drive an instrumented test vehicle along a test corridor. In another scenario, five drivers drove through a roundabout in the University of Iowa national Advanced Driving Simulator (NADS). Models for each scenario were also developed in Vissim. Model output was compared to field collected speed/acceleration profile data to assess the accuracy of microsimulation models in providing realistic estimates of vehicle activity as input to MOVES. Results were summarized to demonstrate the applicability of linking microsimulated vehicle activity data with emissions models to better estimate the emission impacts of different transportation strategies" (page vii).
Download or read book Speed Reduction Methods and Studies in Work Zones written by R. F. Benekohal and published by . This book was released on 1992 with total page 82 pages. Available in PDF, EPUB and Kindle. Book excerpt: The objectives of this project were to determine the effectiveness of speed control methods and study traffic behavior in construction zones. This report provides a brief introduction and summary of findings from the following reports which were prepared as part of this study: (1) Evaluation and Summary of Studies in Speed Control Methods in Work Zones. (2) Evaluation of a Radar-Activated Horn System for Speed Control in Highway Maintenance Operations. (3) Survey of Driver's Opinion about Work Zone Traffic Control on a Rural Highway. (4) Speed Reduction Effects of Drone Radar in Rural Interstate Work Zones. (5) Speed Reduction Effects of Changeable Message Signs in a Construction Zone. (6) Effects of Police Presence on Speed in a Highway Work Zone: Circulating Marked Police Car Experiment. (7) Evaluation of Work Zone Speed Limit Signs with Strobe Lights. (8) Speed Reduction Profiles of Vehicles in a Highway Construction zone. Data only for those vehicles in free flow traffic are used for speed reduction evaluation. A vehicle was considered to be in free flow traffic when its time headway was greater than 5 seconds.
Download or read book Human Performance written by National Research Council (U.S.). Transportation Research Board and published by . This book was released on 2005 with total page 180 pages. Available in PDF, EPUB and Kindle. Book excerpt: This Transportation Research Record contains 22 papers on human performance or simulation and visualization. Among the topics discussed are the following: crash involvement of young novice drivers; factors affecting the safety of young and older drivers; behavioral classification of passing maneuvers; in-vehicle text messages; measuring performance for the Federal Aviation Administration's safety oversight system; driver eye glance behavior during lane change decision, lane changes, and straight-ahead driving; driver fatigue, distraction, and performance; eye glance behavior during in-vehicle secondary tasks; multifunction interfaces in vehicles; interface workload of in-vehicle information systems; human-machine interface design for intelligent speed adaptation; an automated real-time driver warning system; fuzzy sets for evaluating driver perception of variable message signs; video advertising signs and traffic safety; message display formats of portable variable message signs; in-vehicle Global Positioning System data for evaluating deceleration at stop sign-controlled intersections; simulator evaluations of driving with vision impairments and visual aids; a driving simulator for work zone design; the application of visualization to transportation systems; a four-dimensional interactive visualization system for transportation management and traveler information; and virtual reality visualization of microscopic traffic simulations.
Download or read book A Driving Simulator Study to Evaluate the Impact of Portable Changeable Message Signs PCMS on Driver Speed Characteristics written by Bharath Kolar Venkat and published by . This book was released on 2014 with total page 184 pages. Available in PDF, EPUB and Kindle. Book excerpt: "This research project examined the effects of sequential Portable Changeable Message Signs (PCMS) on driver behavior in work zones. PCMS are temporary traffic control (TTC) devices, part of Intelligent Transportation Systems, which supplement static signs to provide advance warning and real-time information to drivers. Text and number based messages are displayed on the PCMS for which detailed evaluation has not been carried out before. This research fills this gap using a driving simulator (DS) supplemented by objective and subjective surveys. A work zone on I-44 in rural Missouri was replicated in the DS using video recordings and GIS (Geographical Information System) data. The DS experiment consisted of five scenarios (0-4). The control scenario (scenario-0) was compared to scenarios 1-4. In the DS, evaluation of the four message signs displayed on the PCMS used by the Missouri Department of Transportation (MoDOT) and their effects on drivers' speed was carried out. The results from the experiment showed significant decrease in speed of driver as a result of the type of messages displayed by the PCMS. From the objective analysis results, message sign-4 (MS-4) saw the maximum decrease in the speeds of drivers when compared to the control scenario. The subjective (survey) results showed that MS-2 was the most preferred message as it displayed a specific speed limit for the participants to follow. Also, the 85th percentile speeds before the construction zone closely matched with the displayed speed for MS-2. The results obtained from the subjective survey reinforced the fact that PCMS were effective in reducing the speed of the drivers"--Abstract, leaf iii.
Download or read book Work Zone Simulation Model written by T. H. Maze and published by . This book was released on 1999 with total page 52 pages. Available in PDF, EPUB and Kindle. Book excerpt: To support the analysis of driver behavior at rural freeway work zone lane closure merge points, Center for Transportation Research and Education staff collected traffic data at merge areas using video image processing technology. The collection of data and the calculation of the capacity of lane closures are reported in a companion report, "Traffic Management Strategies for Merge Areas in Rural Interstate Work Zones". These data are used in the work reported in this document and are used to calibrate a microscopic simulation model of a typical, Iowa rural freeway lane closure. The model developed is a high fidelity computer simulation with an animation interface. It simulates traffic operations at a work zone lane closure. This model enables traffic engineers to visually demonstrate the forecasted delay that is likely to result when freeway reconstruction makes it necessary to close freeway lanes. Further, the model is also sensitive to variations in driver behavior and is used to test the impact of slow moving vehicles and other driver behaviors. This report consists of two parts. The first part describes the development of the work zone simulation model. The simulation analysis is calibrated and verified through data collected at a work zone in Interstate Highway 80 in Scott County, Iowa. The second part is a user's manual for the simulation model, which is provided to assist users with its set up and operation. No prior computer programming skills are required to use the simulation model.
Download or read book Work Zone Speed Management written by John W. Shaw and published by . This book was released on 2015 with total page 152 pages. Available in PDF, EPUB and Kindle. Book excerpt: This synthesis documents information regarding the current state of practice for work zone speed management. The report compiles data, procedures, techniques, and technical issues related to observing and comparing work zone speeds. The speed management measures have been organized into four categories: engineering, operational, enforcement, and public education and outreach. Information included in this study was acquired through a review of the literature, two surveys of state department of transportation representatives in all states, a compilation of state agency public information campaigns, and follow-up interviews with select survey respondents from several U.S. states and one Canadian province.
Download or read book Driving Simulator Use and Calibration for Work Zone Merge Sign Evaluation written by Linlin Zhang (M.S. in civil engineering) and published by . This book was released on 2018 with total page 75 pages. Available in PDF, EPUB and Kindle. Book excerpt: Work zones on highways have the potential to increase crash risk; therefore, efficient and noticeable signs play a critical role in enhancing highway safety. Some engineers have suggested that the traditional Manual on Uniform Traffic Control Devices (MUTCD) merge sign cannot be easily recognized by the driving public due to its graphical nature. In addition, the advance warning areas in work zones exhibit a higher crash rate than the transition, activity, and termination areas, therefore it is beneficial to focus on signage that will impact the advanced warning area of the work zone. A driving simulator is a virtual reality tool that can simulate different driving scenarios and can complement traditional field work due to its feasibility, safety, and cost-effectiveness. In this thesis, a driving simulator was applied to model six scenarios, including three different types of merge signs: MUTCD (baseline), MoDOT, and Quebec. Each merge sign was tested twice in both right lane closed and left lane closed work zone situations. The lane closure scenarios were alternated out of concern that participants might become accustomed to staying in one specific lane. Participants were randomly assigned to a different scenario sequence, thus avoiding sequence bias. A post-experiment survey and a motion sickness screening questionnaire were used to assess driver impressions of the signage and comfort level with the simulator. The results of both the experiment and survey showed that for three different merge signs, participants sustained comparable speeds when passing work zones. For the MoDOT sign, participants merged earlier into the open lane than they did with the other two signs. The MoDOT sign also resulted in the smallest standard deviation of merge location among the three signs. This means that participants reacted to the MoDOT sign consistently. The work zone with the MUTCD sign resulted in the highest speed differential between the merge location and the work zone lane drop taper. Even though 29.4% participants incorrectly perceived the meaning of MUTCD signs compared with only 3.7% for the other two signs, the participants who did correctly understand the MUTCD sign rated the sign positively.
Download or read book Traffic Simulation and Data written by Winnie Daamen and published by CRC Press. This book was released on 2014-09-17 with total page 264 pages. Available in PDF, EPUB and Kindle. Book excerpt: A single source of information for researchers and professionals, Traffic Simulation and Data: Validation Methods and Applications offers a complete overview of traffic data collection, state estimation, calibration and validation for traffic modelling and simulation. It derives from the Multitude Project—a European Cost Action project that incorporates work packages defining traffic simulation practice and research; highway and network modeling; and synthesis, dissemination, and training. This book addresses the calibration and validation of traffic models, and introduces necessary frameworks and techniques. It also includes viable methods for sensitivity analyses, and incorporates relevant tools for application. The book begins with a brief summary of various data collection techniques that can be applied to collect different data types. It then showcases various data processing and enhancement techniques for improving the quality of collected data. It also introduces the techniques according to the type of estimation, for example microscopic data enhancement, traffic state estimation, feature extraction and parameter identification techniques, and origin–destination matrix estimation. The material discusses the measures of performance, data error and goodness of fit, and optimization algorithms. It also contains the sensitivity analyses of parameters in traffic models. Describes the various tasks of calibration and validation Considers the best use of available data Presents the sensitivity analysis method Discusses typical issues of data error in transportation system data and how these errors can impact simulation results Details various methodologies for data collection, sensitivity analysis, calibration, and validation Examines benefits that result from the application of these methods Traffic Simulation and Data: Validation Methods and Applications serves as a key resource for transport engineers and planners, researchers, and graduate students in transport engineering and planning.
Download or read book Handbook of Driving Simulation for Engineering Medicine and Psychology written by Donald L. Fisher and published by CRC Press. This book was released on 2011-04-25 with total page 728 pages. Available in PDF, EPUB and Kindle. Book excerpt: Effective use of driving simulators requires considerable technical and methodological skill along with considerable background knowledge. Acquiring the requisite knowledge and skills can be extraordinarily time consuming, yet there has been no single convenient and comprehensive source of information on the driving simulation research being conduc
Download or read book Work Zone Simulator Analysis written by Suzanna Long and published by . This book was released on 2016 with total page 92 pages. Available in PDF, EPUB and Kindle. Book excerpt: Improving work zone road safety is an issue of great interest due to the high number of crashes observed in work zones. Department's of Transportation (DOTs) use a variety of methods to inform drivers of upcoming work zones. One method used by DOTs is work zone signage configuration. It is necessary to evaluate the efficiency of different configurations, by law, before implementation of new signage designs that deviate from national standards. This research presents a driving simulator based study, funded by the Missouri Department of Transportation (MoDOT) that evaluates a driver’s response to work zone sign configurations. This study has compared the Conventional Lane Merge (CLM) configurations against MoDOT's alternate configurations. Study participants within target populations, chosen to represent a range of Missouri drivers, have attempted four work zone configurations, as part of a driving simulator experience. The test scenarios simulated both right and left work zone lane closures for both the CLM and MoDOT alternatives. Travel time was measured against demographic characteristics of test driver populations. Statistical data analysis was used to investigate the effectiveness of different configurations employed in the study. The results of this study were compared to results from a previous MoDOT to compare result of field and simulation study about MoDOT's alternate configurations.
Download or read book CONVR 2023 Proceedings of the 23rd International Conference on Construction Applications of Virtual Reality written by Pietro Capone and published by Firenze University Press. This book was released on with total page 1279 pages. Available in PDF, EPUB and Kindle. Book excerpt: Within the overarching theme of “Managing the Digital Transformation of Construction Industry” the 23rd International Conference on Construction Applications of Virtual Reality (CONVR 2023) presented 123 high-quality contributions on the topics of: Virtual and Augmented Reality (VR/AR), Building Information Modeling (BIM), Simulation and Automation, Computer Vision, Data Science, Artificial Intelligence, Linked Data, Semantic Web, Blockchain, Digital Twins, Health & Safety and Construction site management, Green buildings, Occupant-centric design and operation, Internet of Everything. The editors trust that this publication can stimulate and inspire academics, scholars and industry experts in the field, driving innovation, growth and global collaboration among researchers and stakeholders.
Download or read book Speed Reduction Profiles of Vehicles in a Highway Construction Zone written by and published by . This book was released on 1992 with total page 200 pages. Available in PDF, EPUB and Kindle. Book excerpt: In response to roadway geometry and traffic control devices, motorists may change their speeds within in a work zone. Speed profile data were collected for 208 vehicles who traveled a 1 .5-mile long section of a work zone, and speed reduction patterns were determined for Autos and Trucks. Four driver categories were identified based on the patterns. About 61% of the drivers reduced their speeds considerably after the first work zone speed limit signs, but nearly 15% of the drivers did not reduce their speeds until they neared the location of construction activities. About 11% of the drivers traveled at consistently high speeds and did not considerably reduce their speeds. The remaining drivers did not display a common pattern. The average speeds of Autos and Trucks were 5-18 mph and 1-12 mph, respectively, over the work zone speed limit. Vehicles decreased their speeds to the lowest level near the work space, but increased them after passing it. Even at the work space, about 65% of Autos and 47% of Trucks traveled faster than the speed limit. Autos and Trucks reduced their speeds by 3-13 mph and 3-12 mph, respectively, compared to their speeds at the beginning of the taper. The speeds at the beginning of the taper were used to group the vehicles into four speed groups. The maximum reduction in the average speed at different locations was greater with greater initial mean speeds; indicating that, on the average, the vehicles with higher initial speeds reduced their speeds more than the vehicles with lower initial speeds. However, the drivers in the higher initial speed groups kept higher speeds in the work zone than the drivers in the lower initial speed groups, even though the former group had greater speed reductions than the latter group.
Download or read book Evaluation and Summary of Studies in Speed Control Methods in Work Zones written by R. F. Benekohal and published by . This book was released on 1992 with total page 114 pages. Available in PDF, EPUB and Kindle. Book excerpt: This report summarizes and evaluates the important findings from the literature review of the studies on work zone speed control techniques. The following treatments are included in this report: 1) flagging, 2) lane width reduction, 3) law enforcement, 4) changeable message signs (CMS), 5) rumble strips, and 6) flashing beacons. The effects of the speed control treatments on speed and traffic flow are evaluated based on: A) experiences with treatment, B) effects of treatment on speed, C) effectiveness of treatment, and D) comments about treatment. A brief description of the conditions under which the treatments were applied is provided, and the speed reduction effects of each technique are discussed. A reference matrix was prepared to identify publications related to each type of speed reduction treatment used in work zones.
Download or read book Effectiveness of Speed Management Methods in Work Zones written by Henry Brown and published by . This book was released on 2022 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: "Management of speeds is a significant component of any strategy to reduce work zone crashes. The objective of this study is to investigate the effectiveness of speed management countermeasures, such as speed display trailer, speed display trailer with red and blue lights, work vehicle with red and blue lights, and active and passive law enforcement, in managing vehicle speeds in work zones. The research methodology includes a review of the existing literature, field study, simulator study, and driver survey. The field study was conducted at a work zone on I-270 in the St. Louis region. All speed countermeasures tested in the field study achieved speed reductions. Active law enforcement was the most effective speed countermeasure for both daytime and nighttime conditions. Thirteen scenarios were studied using a driving simulator. Combining a speed display trailer and active law enforcement was the most effective countermeasure for daytime conditions. Using a speed display trailer by itself was the most effective for nighttime conditions. While respondents to both the driver and post-simulator surveys generally preferred the speed display trailer, they also admitted that the presence of law enforcement would be the most effective in causing them to slow down. Overall, the results of the study indicate that any of the tested countermeasures would help reduce speeds in a work zone. In some instances, deploying multiple countermeasures at the same site was found to be the most effective speed reduction strategy"--Abstract.
