Download or read book Wheel Radial Impact Test Procedure for Passenger Cars written by Wheel Standards Committee and published by . This book was released on 2023 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This SAE Recommended Practice defines the test stand and procedure for evaluating radial impacts of all wheels intended for passenger cars and light trucks. A minimum performance requirement is intentionally not provided. The intent is to establish a uniform method and test stand for imparting damage and evaluating radial impacts. A minimum performance requirement will be a proposed change when users determine what is of most value. A laboratory test is provided to simulate the impact imparted to a tire and wheel assembly from a pothole and or above the road surface road hazard.

Download or read book Wheels Lateral Impact Test Procedure Road Vehicles written by Wheel Standards Committee and published by . This book was released on 2016 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: The SAE Recommended Practice establishes minimum performance requirements and related uniform laboratory test procedures for evaluating lateral (curb) impact collision resistance of all wheels intended for use on passenger cars and light trucks.A process of compensating for frictional losses is recommended to minimize test variation between machines and assure the anticipated velocity is met. The machine calibrator will determine the Adjusted Drop Height (ADH) that the respective machine must drop from to replicate 230 mm of free fall.Certifying the spring rate of the four rubber mounts is difficult in the apparatus as originally shown in the document. An alternate method to certify the spring rate is provided using common load vs deflection machines. One can certify rubber mounts four at a time.Test pressures for temporary T' and light truck LT' applications are provided since they operate at pressures substantially different than passenger P' tires. The intent is to test the wheel at the lower end of the pressure specified for the application.The document title is changed to include "Lateral Impact" to distinguish it from the road hazard impact test that uses an impact in a radial direction per SAE J1981.Reports for the lateral impact test and calibration are in the appendix to ensure uniform reporting. Refer to Appendix A. An alternate construction allowing for constraining the rubber mount and rotating the wheel while on the machine is provided. Background of Lateral Impact Test Procedure Road Vehicles is provided. Refer to Appendix C.

Download or read book Road Hazard Impact Test for Wheel and Tire Assemblies Passenger Car Light Truck and Multipurpose Vehicles written by Wheel Standards Committee and published by . This book was released on 2016 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: The test is designed to evaluate the frontal impact resistance of wheel and tire assemblies used with passenger cars, light trucks and multi-purpose vehicles. The test is specifically related to vehicle pothole tests that are undertaken by most vehicle manufacturers. The scope has been expanded to allow the use of a striker that can be angled to preferentially impact the inboard and outboard wheel flange. For side impact of the outboard rim flange only, please refer to SAE J175. This SAE Recommended Practice provides a procedure to test a wheel or a tire and the test failure criteria. The specific test for a vehicle requires input from a pothole test on that vehicle to establish the drop height of the striker used in this test. This technical report is being Stabilized because it covers technology, products, or processes which are mature and not likely to change in the foreseeable future.

Download or read book WHEELS PASSENGER CARS IMPACT PERFORMANCE REQUIREMENTS AND TEST PROCEDURES written by Wheel Standards Committee and published by . This book was released on 1970 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This SAE Recommended Practice establishes minimum performance requirements and related uniform laboratory test procedures for evaluating impact characteristics of all wheels intended for use on passenger cars.

Download or read book Wheels Impact Test Procedures Road Vehicles written by Wheel Standards Committee and published by . This book was released on 1988 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This SAE Recommended Practice establishes minimum performance requirements and related uniform laboratory test procedures for evaluating axial (lateral) curb impact collision properties of all wheels intended for use on passenger cars and light trucks. It is equivalent to ISO 7141-1981with the excpetion of the Definitions section which cites SAE J393.

Download or read book QC T 991 2015 Translated English of Chinese Standard QCT 991 2015 QC T991 2015 QCT991 2015 written by https://www.chinesestandard.net and published by https://www.chinesestandard.net. This book was released on 2018-10-05 with total page 17 pages. Available in PDF, EPUB and Kindle. Book excerpt: This standard specifies two laboratory test methods, I and II, to assess the strength and safety performance of the wheel when the wheel is subjected to the impact perpendicular to the axis. It may select either of the two methods to carry out test. This standard applies to light alloy wheels of passenger cars.

Download or read book Road Hazard Impact Test for Wheel and Tire Assemblies Passenger Car Light Truck and Multipurpose Vehicles written by Road Hazard Impact Test Task Force (J1981) and published by . This book was released on 1994 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: The test is designed to evaluate the frontal impact resistance of wheel and tire assemblies used with passenger cars, light trucks and multi-purpose vehicles. The test is specifically related to vehicle pothole tests that are undertaken by most vehicle manufacturers. The scope has been expanded to allow the use of a striker that can be angled to preferentially impact the inboard and outboard wheel flange. For side impact of the outboard rim flange only, please refer to SAE J 175. This SAE Recommended Practice does not provide standards of performance.

Download or read book Aftermarket Wheels Passenger Cars and Light Truck Performance Requirements and Test Procedures written by Wheel Standards Committee and published by . This book was released on 2021 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This SAE Recommended Practice provides performance, sampling, certifying requirements, test procedures, and marking requirements for aftermarket wheels intended for normal highway use on passenger cars, light trucks, and multipurpose passenger vehicles. For aftermarket wheels on trailers drawn by passenger cars, light trucks, or multipurpose vehicles, refer to SAE J1204. These performance requirements apply only to wheels made of materials included in Tables 1 and 2. For wheels using composite material, refer to SAE J3204. New nomenclature and terms are added to clarify wheel constructions typically not used in OEM applications. The testing procedures and requirements are based on SAE standards listed in the references. Editorial changes made to improve grammar and SAE procedure. Added reference to new composite wheel testing: SAE J3204. Revised stamping specification to allow other permanent markings without having to either emboss or stamp into the wheel. Changed the special restriction wheel use stamping example to "limited use spare only". Added to radial test criteria/test termination the statement that all bolts must be replaced if lug bolts are replaced to match the cornering test criteria.

Download or read book Wheels Recreational and Utility Trailer Test Procedure written by Wheel Standards Committee and published by . This book was released on 2007 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This SAE Recommended Practice provides uniform procedures and minimum performance requirements for fatigue testing ferrous and aluminum wheels intended for normal highway use on travel, camping, and boat and light utility trailers drawn by passenger cars, light trucks, and multipurpose vehicles. (See Figures 1 and 2.) For procedures and minimum performance requirements for wheels used on trucks, see SAE J267, and for wheels used on passenger cars, see SAE J328. For the application of passenger car and light ruck wheels [inset less than 0.10 m (0.33 ft)] to this trailer service, use this procedure. For the application of heavier truck wheels [inset 0.10 m (0.33 ft) or mre] use SAE J267. Mobile home service is outside the scope of this document. There are two basic test procedures described, a cornering fatigue test and radial fatigue test. The cornering test is directed at the wheel disc; whereas the radial test also examines the rim and attachment portion of the wheel. Both test procedures are required to obtain a thorough examination of the wheel.

Download or read book Wheels Impact Test Procedure Road Vehicles written by Society of Automotive Engineers and published by . This book was released on 2003 with total page 10 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book WheelsImpact Test ProcedureRoad Vehicles written by Wheel Standards Committee and published by . This book was released on 2003 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: The SAE Recommended Practice establishes minimum performance requirements and related uniform laboratory test procedures for evaluating axial (lateral) curb impact collision properties of all wheels intended for use on passenger cars and light trucks. It is equivalent to ISO 7141-1981 with the exception of the Definitions section which cites SAE J393. Not applicable.

Download or read book Wheels Passenger Car and Light Truck Performance Requirements and Test Procedures written by Wheel Standards Committee and published by . This book was released on 2021 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This SAE Recommended Practice provides minimum performance requirements and uniform procedures for fatigue testing of wheels intended for normal highway use and temporary use on passenger cars, light trucks, and multipurpose vehicles. For heavy truck wheels and wheels intended to be used as duals, refer to SAE J267. For wheels used on trailers drawn by passenger cars, light trucks, or multipurpose vehicles, refer to SAE J1204. These minimum performance requirements apply only to wheels made of materials included in Tables 1 to 4. The minimum cycles noted in Tables 1 through 4 are to be used on individual test and a sample of tests conducted, with Weibull Statistics using two parameter, median ranks, 50% confidence level, and 90% reliability, typically noted as B10C50. This document has been updated to add a reference to SAE J3204.

Download or read book Surface Vehicle Recommended Practice written by and published by . This book was released on 2016 with total page 11 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Wheels Rims Truck and Bus Performance Requirements and Test Procedures for Radial and Cornering Fatigue written by Truck and Bus Wheel Committee and published by . This book was released on 2014 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This SAE Recommended Practice provides minimum performance requirements and uniform laboratory procedures for fatigue testing of wheels and demountable rims intended for normal highway use on trucks, buses, truck-trailers, and multipurpose vehicles. Users may establish design criteria exceeding the minimum performance requirement for added confidence in a design. The cycle requirements noted in Tables 1 and 2 are based on Weibull statistics using 2 parameter, median ranks, 50% confidence level and 90% reliability, and beta equal to 2, typically noted as B10C50. For other wheels intended for normal highway use and temporary use on passenger cars, light trucks, and multipurpose vehicles, see SAE J328. For wheels used on trailers drawn by passenger cars, light trucks, or multipurpose vehicles, see SAE J1204. For bolt together military wheels, see SAE J1992. This document does not cover other special application wheels and rims. SAE J267 practitioners have typically performed multiple cornering and radial fatigue tests when assessing a wheel design's conformance with this recommended practice. Running multiple tests enhances the confidence and reliability of the results. In this revision, this common practice has been formalized by introducing a set of sample sizes and corresponding cycle requirements based on Weibull statistics.Previous publications of SAE J267 contained terminology to "provide minimum performance requirements". This terminology was not consistently interpreted by practitioners. To clarify the meaning, a definition of the term "minimum performance requirement" has been added.An additional cause for termination was added for aluminum wheels.

Download or read book WHEELSRECREATIONAL AND UTILITY TRAILER TEST PROCEDURES written by Wheel Standards Committee and published by . This book was released on 1977 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This SAE Recommended Practice provides uniform procedures for fatigue testing ferrous wheels intended for normal highway use on travel, camping, boat and light utility trailers drawn by passenger cars and light trucks. For performance requirements, see SAE Jxxx. For procedures and minimum performance requirements for truck-type rims and wheels, see SAE J267a and for passenger car rims and wheels see SAE J328a. Mobile home service is also outside the scope of this recommended practice.There are two basic test procedures described, a cornering fatigue test and a radial fatigue test. The cornering test is directed at the wheel portion of the wheel/rim assembly; whereas the radial test will examine potential deficiencies in the rim portion of the structure. Both test procedures are required to obtain a thorough examination of the wheel/rim assembly.

Download or read book Road Vehicles Passenger Car Wheels for Road Use Test Methods written by British Standards Institute Staff and published by . This book was released on 1915-06-30 with total page 20 pages. Available in PDF, EPUB and Kindle. Book excerpt: Road vehicles, Passenger road vehicles, Vehicles, Test methods, Fatigue testing, Radial, Wheels, Vehicle components

Download or read book Impact Resistance of Non ferrous Passenger Car Wheels Modification Number Two 2 Final Report written by Jerry G. Wallingford and published by . This book was released on 1978 with total page 22 pages. Available in PDF, EPUB and Kindle. Book excerpt: