Download or read book Welding of High strength Steels for Aircraft and Missile Applications written by Herbert W. Mishler and published by . This book was released on 1959 with total page 106 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Welding High strength Steels written by P. A. Kammer and published by . This book was released on 1966 with total page 68 pages. Available in PDF, EPUB and Kindle. Book excerpt: Recent studies of the developments in welding steels with yield strengths greater than 150 ksi have included low-alloy martensitic steels, medium-alloy martensitic steels, nickel maraging steels, and bainitic steels. Only weldments from medium-alloy martensitic steels and nickel maraging steels have mechanical properties approaching those of the base plate without a complete postweld heat treatment. The most serious problem with the other steel is low toughness in the weld fusion zone. Adequate weld metal toughness under conditions of elastic strain can be obtarined over the entire 150 to 225 ksi yield-strength range only if the tungsten-arc welding process is used. Processes with higher deposition rates can produce comparable weld deposits only in the lower portion of the range. Above a yield strength of 200 ksi, 18Ni maraging steel weldments have the best combination of strength and toughness. Below 200 ksi, the HP 9-4-25 medium-alloy martensitic steel and 12Ni maraging steel weldments have nearly equal properties.
Download or read book High strength steel Forgings written by H. J. Henning and published by . This book was released on 1961 with total page 68 pages. Available in PDF, EPUB and Kindle. Book excerpt: THIS REPORT IS MAINLY CONCERNED WITH FORGINGS MADE FROM MARTENSITIC STEELS HEAT TREATED TO STRENGTHS RANGING FROM 240,000 TO 300,000 PSI. FORGING CHARACTERISTICS, DESIGN LIMITATIONS, DIMENSIONAL TOLERANCES, AND QUALITY-CONTROL PROBLEMS ARE DISCUSSED. A CONSIDERABLE AMOUNT OF DATA ON MECHANICAL PROPERTIES IS ALSO PRESENTED. IN ADDITION, THE REPORT SUMMARIZES THE AVAILABLE INFORMATION ON FORGED, SEMIAUSTENITIAL STEELS. THIS COMPILATION IS BASED ON PUBLISHED ARTICLES, GOVERNMENT REPORTS, AND INTERVIEWS WITH PRODUCERS AND USERS OF STEEL FORGINGS.
Download or read book Department of Defense Refractory Metals Sheet rolling Program written by H. R. Ogden and published by . This book was released on 1961 with total page 44 pages. Available in PDF, EPUB and Kindle. Book excerpt: A summary is presented of the status of the Department of Defense Refractory Metals SheetRolling Program to accelerate the development of production techniques for high-quality, consistent sheet products from the refractory metals (Nb, Mo, Ta, and W) and their alloys. The program includes: (1) development of sheet production techniques, (2) establishment of minimum data re uired to evaluate mill production, (3) evaluation of fabrication characteristics of the sheet produced, and (4) establishment of design data. Contracts were awarded for the development of sheet production techniques for all four refractory metals. One contract was awarded for the evaluation of Mo alloy sheet fabrication characteristics. (Author).
Download or read book Coatings for the Protection of Refractory Metals from Oxidation written by Carol Alnoth Krier and published by . This book was released on 1961 with total page 248 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book A Summary of the Theory of Fracture in Metals written by J. W. Spretnak and published by . This book was released on 1961 with total page 70 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Status Report No 2 on Department of Defense Refractory Metals Sheet rolling Program written by H. R. Ogden and published by . This book was released on 1962 with total page 54 pages. Available in PDF, EPUB and Kindle. Book excerpt: The Nb program is nearing completion of laboratory tory rolling studiory materials, *Heat resistant alloys, *Sheets, Niobium alloys, Molybdenum alloys, Tantalum alloys, Tungsten alloys, Titanium alloys, Zirconium alloys, Tungsten, Powder metallurgy, Electric arcs, Manufacturing methods, Mechanical proper ies, Forging, Heat treatment, Melting, Extrusion, Deformation, Hardness, Rolling mills, Processing. Identifiers: Floturning. The Nb program is nearing completion of laboratory tory rolling studies, and a single composition for larger scale rolling studies will be selected in the near future. In the Mo program, it has been shown that true hot forging of billets to sheet bar results in higher recrystallization temperatures of TZM and Mo-0.5Ti sheet than are obtained when normal forging temperatures are used. The Ta program is in the early stages of ingot production and primary breakdown fabrication of the Ta-30Nb-7.5V alloy. Three methods of fabricating W sheet are being investigated: rolling of powder-metallurgy billets, fabrication of arc-melted ingots, and floturning of cylindrical blanks. Properties obtained on both powdermetallurgy and arc-melted tungsten sheet compare very favorably. Evaluation of the formability of Mo-alloy sheet has been delayed until sheet is available from the production program. (Author).
Download or read book Design Considerations in Selecting Materials for Large Solid propellant Rocket motor Cases written by Charles Wesley Bert and published by . This book was released on 1962 with total page 80 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book The Effect of Nuclear Radiation on Structural Metals written by Frederic R. Shober and published by . This book was released on 1961 with total page 120 pages. Available in PDF, EPUB and Kindle. Book excerpt: The effect of fast-neutron (>1 Mev) irradiation on the mechanical properties of structural metals and alloys was studied. Although the yield strengths and ultimate tensile strengths are increased su stantially for most materials, the ductility suffers severe decreases. This report presents these changes in properties of several structural metals for a number of neutron exposures within the 1.0 x 10 to the 18th power to 5.0 x 10 to the 21st power n/sq cm range. Data summarizing these effects on several classes of materials such as carbon steels, low-alloy steels, stainless steels, Zr-base alloys, ni-base alloys, Al-base alloys, and Ta are given. Additional data which show the influence f irradiation temperatures and of post-irradiation annealing on the radiation-induced property changes are also given and discussed. Increases as great as 175% in yield strength, 100% in ultimate strength, and decreases of 80% in total elongation are reported for fast-neutron exposures as great as 5 10 to the 21st power n/sq cm. (Author).
Download or read book Strain Aging of Refractory Metals written by A. G. Imgram and published by . This book was released on 1960 with total page 68 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book A Discussion of the Physical Metallurgy of the 18 Per Cent Nickel Maraging Steels written by Albert M. Hall and published by . This book was released on 1963 with total page 34 pages. Available in PDF, EPUB and Kindle. Book excerpt: Various aspects of the physical metallurgy of the 18 % nickel maraging steels are discussed in this report in the light of the knowledge which has thus far been accumulated on these steels. The 18 % nickel type of maraging steel was singled out for discussion because of its especially attractive combination of strength and fracture toughness, the comparative simplicity with which it can be hardened, and the relative ease with which it can be formed and joined. The highnickel maraging steels are considered to be outstanding members of a loose-knit family of agehardenable or precipitation-hardenable martensitic steels. Some comparisons and analogies are drawn among various members of this family with particular reference to the 18% nickel steels. (Author).
Download or read book The Effects of Alloying Elements in Titanium written by D. J. Maykuth and published by . This book was released on 1960 with total page 246 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book The Physical Metallurgy of Cobalt base Superalloys written by H J Wagner and published by . This book was released on 1962 with total page 102 pages. Available in PDF, EPUB and Kindle. Book excerpt: A detailed picture is presented of the physical and chemical phenomena that affect the behavior of cobalt-base superalloys. Solid-solution strengthening is obtained from the high-melting metallic elements molybdenum, tungsten, tantalum, and columbium. These elements also participate in precipitation reactions involving their carbides. Precipitation of intermetallic compounds such as Ni3Ti is an important process in cobalt alloys containing appreciable amounts of nickel and titanium. The relationships among microstructure, heat treatment, and mechanical properties of the important commercial alloys are considered, and whenever possible, explained on the basis of the physical and chem cal processes that occur. (Author).
Download or read book The Engineering Properties of Columbium and Columbium Alloys written by F. F. Schmidt and published by . This book was released on 1963 with total page 264 pages. Available in PDF, EPUB and Kindle. Book excerpt: The results of a state-of-the-art survey covering niobium and 18 of its most promising alloys are presented. All data are given in tabular and graphical form covering some of the more important physical, mechanical, and metallurgical properties for each material. References are given at the conclusion of each material section.
Download or read book The Status and Properties of Titanium Alloys for Thick Plate written by G. E. Faulkner and published by . This book was released on 1963 with total page 60 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Thermal Radiative Properties of Selected Materials written by W. D. Wood and published by . This book was released on 1962 with total page 290 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Binary and Ternary Phase Diagrams of Columbium Molybdenum Tantalum and Tungsten written by J. J. English and published by . This book was released on 1963 with total page 190 pages. Available in PDF, EPUB and Kindle. Book excerpt: This report supplements DMIC Report 152 which is a compilation of binary and ternary phase diagrams of columbium, molybdenum, tantalum, and tungsten. Forty new binary and 80 new ternary diagrams are included, some of these being revised versions of the previously published diagrams. Included with each binary diagram and with some ternary diagrams is a short discussion listing terminal solubilities and crystal struc tures of intermediate pahses. Many of the diagrams are tentative and are subject to revision as additional data become available. (Author).
