Download or read book Ultrasonic and Advanced Methods for Nondestructive Testing and Material Characterization written by Chi-hau Chen and published by World Scientific. This book was released on 2007 with total page 682 pages. Available in PDF, EPUB and Kindle. Book excerpt: Ultrasonic methods have been very popular in nondestructive testing and characterization of materials. This book deals with both industrial ultrasound and medical ultrasound. The advantages of ultrasound include flexibility, low cost, in-line operation, and providing data in both signal and image formats for further analysis. The book devotes 11 chapters to ultrasonic methods. However, ultrasonic methods can be much less effective with some applications. So the book also has 14 chapters catering to other or advanced methods for nondestructive testing or material characterization. Topics like structural health monitoring, Terahertz methods, X-ray and thermography methods are presented. Besides different sensors for nondestructive testing, the book places much emphasis on signal/image processing and pattern recognition of the signals acquired.

Download or read book Materials Characterization Using Nondestructive Evaluation NDE Methods written by Gerhard Huebschen and published by Woodhead Publishing. This book was released on 2016-03-23 with total page 322 pages. Available in PDF, EPUB and Kindle. Book excerpt: Materials Characterization Using Nondestructive Evaluation (NDE) Methods discusses NDT methods and how they are highly desirable for both long-term monitoring and short-term assessment of materials, providing crucial early warning that the fatigue life of a material has elapsed, thus helping to prevent service failures. Materials Characterization Using Nondestructive Evaluation (NDE) Methods gives an overview of established and new NDT techniques for the characterization of materials, with a focus on materials used in the automotive, aerospace, power plants, and infrastructure construction industries. Each chapter focuses on a different NDT technique and indicates the potential of the method by selected examples of applications. Methods covered include scanning and transmission electron microscopy, X-ray microtomography and diffraction, ultrasonic, electromagnetic, microwave, and hybrid techniques. The authors review both the determination of microstructure properties, including phase content and grain size, and the determination of mechanical properties, such as hardness, toughness, yield strength, texture, and residual stress. - Gives an overview of established and new NDT techniques, including scanning and transmission electron microscopy, X-ray microtomography and diffraction, ultrasonic, electromagnetic, microwave, and hybrid techniques - Reviews the determination of microstructural and mechanical properties - Focuses on materials used in the automotive, aerospace, power plants, and infrastructure construction industries - Serves as a highly desirable resource for both long-term monitoring and short-term assessment of materials

Download or read book Ultrasonic and Electromagnetic NDE for Structure and Material Characterization written by Tribikram Kundu and published by CRC Press. This book was released on 2016-04-19 with total page 890 pages. Available in PDF, EPUB and Kindle. Book excerpt: Most books on nondestructive evaluation (NDE) focus either on the theoretical background or on advanced applications. Bridging the gap between the two, Ultrasonic and Electromagnetic NDE for Structure and Material Characterization: Engineering and Biomedical Applications brings together the principles, equations, and applications of ultrasonic and

Download or read book Ultrasonic Techniques for Fluids Characterization written by Malcolm J.W. Povey and published by Academic Press. This book was released on 1997-07-22 with total page 232 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book is a comprehensive and practical guide to the use of ultrasonic techniques for the characterization of fluids. Focusing on ultrasonic velocimetry, the author covers the basic topics and techniques necessaryfor successful ultrasound measurements on emulsions, dispersions, multiphase media, and viscoelastic/viscoplastic materials. Advanced techniques such as scattering, particle sizing, and automation are also presented. As a handbook for industrial and scientific use, Ultrasonic Techniques for Fluids Characterization is an indispensable guide to chemists and chemical engineers using ultrasound for research or process monitoring in the chemical, food processing, pharmaceutical, cosmetic, biotechnology,and fuels industries. Appeals to anyone using ultrasound to study fluids Provides the first detailed description of the ultrasound profiling technique for dispersions Describes new techniques for measuring phase transitions and nucleation, such as water/ice and oil/fat Presents the latest ultrasound techniques for particle sizing in concentrated systems Explains new techniques for compressibility measurements in dispersions and fluids, including cell suspensions Contains a detailed treatment of ultrasound scattering theory Written by one of the leading researchers in the field Includes over 350 references to the primary literature

Download or read book Ultrasonic Testing of Materials written by Josef Krautkrämer and published by Springer Science & Business Media. This book was released on 2013-03-14 with total page 678 pages. Available in PDF, EPUB and Kindle. Book excerpt: The amendments of this third English edition with respect to the second one concern beside some printing errors the replacement of some pictures in part D by more modern ones and updating the list of stand ards to the state of the fourth German edition. J OSEF KRAUTKRÄMER Cologne, January 1983 Preface to the Second Edition This seeond English edition is based on the third German edition. In view of most recent teehnologieal advanees it has beeome neeessary in many instanees to supplement the seeond German edition and to revise some parts completely. In addition to piezo-eleetric methods, others are now also extensively diseussed in Chapter 8. As for the intensity method, ultrasonie holo graphy is treated in the new Seetion 9. 4. In Part B, for reasons of syste maties, the resonanee method has been ineluded under transit-time methods. It appeared neeessary to elaborate in greater detail the defini tion of the properties of pulse-echo testing equipment and their measure ments (10. 4). The more recent findings of pulse speetroscopy (5. 6) and sound-emission analysis (12) are mentioned only in passing because their significanee is still controversial. Apart from numerous additions, partieularly those coneerning automatie testing installations, Part C also eontains a new chapter whieh deals with tests on nu eIe ar reactors (28), as weIl as abrief diseussion of surfaee-hardness tests (32. 4). It beeame impossible to include a critieal analysis of the principal standards in Chapter 33.

Download or read book Nondestructive Characterization of Materials written by Paul Höller and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 894 pages. Available in PDF, EPUB and Kindle. Book excerpt: Engineering structures for reliable function and safety have to be designed such that operational mechanical loads are compensated for by stresses in the components bearable by the materials used. Vhat is "bearable"? First of all it depends on the properties of the chosen materials as well as on several other parameters, e.g. temperature, corrosivity of the environment, elapsed or remaining serviceable life, unexpected deterioration of materials, whatever the source and nature of such deterioration may be: defects, loss of strength, embrittlement, wastage, etc. DEFECTS and PROPERTIES of materials currently determine loadability. Therefore in addition to nondestructive testing for defects there is also a need for nondestructive testing of properties. The third type of information to be supplied by nondestructive measurement pertains to STRESS STATES under OPERATIONAL LOADS, i.e. LOAD-INDUCED plus RESIDUAL STRESSES. Residual stresses normally cannot be calculated; they have to be measured nondestructively; well-approved elastomechanical finite element codes are available and used for calculating load-induced stresses; for redundancy and reliability, engineers, however, need procedures and instrumentation for experimental checks.

Download or read book Ultrasonic Nondestructive Testing of Materials written by Karl-Jörg Langenberg and published by CRC Press. This book was released on 2012-02-22 with total page 756 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book features a comprehensive discussion of the mathematical foundations of ultrasonic nondestructive testing of materials. The authors include a brief description of the theory of acoustic and electromagnetic fields to underline the similarities and differences with respect to elastodynamics. They also cover vector, elastic plane, and Rayleigh surface waves as well as ultrasonic beams, inverse scattering, and ultrasonic nondestructive imaging. A coordinate-free notation system is used that is easier to understand and navigate than standard index notation.

Download or read book Ultrasonic Materials Characterization written by Harold Berger and published by . This book was released on 1980 with total page 680 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Ultrasound for Material Characterization and Processing written by Francesca Lionetto and published by Mdpi AG. This book was released on 2021-11-04 with total page 188 pages. Available in PDF, EPUB and Kindle. Book excerpt: Ultrasonic waves are nowadays used for multiple purposes including both low-intensity/high frequency and high-intensity/low-frequency ultrasound. Low-intensity ultrasound transmits energy through the medium in order to obtain information about the medium or to convey information through the medium. It is successfully used in non-destructive inspection, ultrasonic dynamic analysis, ultrasonic rheology, ultrasonic spectroscopy of materials, process monitoring, applications in civil engineering, aerospace and geological materials and structures, and in the characterization of biological media. Nowadays, it is an essential tool for assessing metals, plastics, aerospace composites, wood, concrete, and cement. High-intensity ultrasound deliberately affects the propagation medium through the high local temperatures and pressures generated. It is used in industrial processes such as welding, cleaning, emulsification, atomization, etc.; chemical reactions and reactor induced by ultrasonic waves; synthesis of organic and inorganic materials; microstructural effects; heat generation; accelerated material characterization by ultrasonic fatigue testing; food processing; and environmental protection. This book collects eleven papers, one review, and ten research papers with the aim to present recent advances in ultrasonic wave propagation applied for the characterization or the processing of materials. Both fundamental science and applications of ultrasound in the field of material characterization and material processing have been gathered.

Download or read book Ultrasonic Transducer Materials written by O. E. Mattiat and published by Springer Science & Business Media. This book was released on 2013-03-13 with total page 194 pages. Available in PDF, EPUB and Kindle. Book excerpt: In recent years remarkable progress has been made in the development of materials for ultrasonic transducers. There is a continuing trend towards increasingly higher frequency ranges for the application of ultrasonic trans ducers in modern technology. The progress in this area has been especially rapid and articles and papers on the subject are scattered over numerous technical and scientific journals in this country and abroad. Although good books have appeared on ultrasonics in general and ultrasonic transducers in particular in which, for obvious reasons, materials play an important part, no comprehensive treatise is available that represents the state-of-the-art on modern ultrasonic transducer materials. This book intends to fill a need for a thorough review of the subject. Not all materials are covered of which, theoretically, ultrasonic trans ducers could be made but those that are or may be of technical impor tance and which have inherent electro acoustic transducer properties, i.e., materials that are either magnetostrictive, electrostrictive, or piezoelectric. The book has been devided into three parts which somewhat reflect the historic development of ultrasonic transducer materials for important tech nical application. Chapter 1 deals with magnetostrictive materials, magnetostrictive met als and their alloys, and magnetostrictive ferrites (polycrystalline ceramics). The metals are useful especially in cases where ruggednes of the transducers are of overriding importance and in the lower ultrasonic frequency range.

Download or read book Ultrasonic Nondestructive Evaluation Systems written by Lester W. Schmerr Jr and published by Springer Science & Business Media. This book was released on 2007-04-22 with total page 602 pages. Available in PDF, EPUB and Kindle. Book excerpt: Using a systems level approach, this book employs aspects of linear systems theory and wave propagation and scattering theory to develop a comprehensive model of an entire ultrasonic measurement system. This integrated approach leads to a new model-based engineering technology for designing, using and optimizing ultrasonic nondestructive evaluation inspections. In addition, the book incorporates MATLAB examples and exercises.

Download or read book Nondestructive Materials Characterization written by Norbert G. H. Meyendorf and published by Springer Science & Business Media. This book was released on 2013-11-21 with total page 435 pages. Available in PDF, EPUB and Kindle. Book excerpt: With an emphasis on aircraft materials, this book describes techniques for the material characterization to detect and quantify degradation processes such as corrosion and fatigue. It introduces readers to these techniques based on x-ray, ultrasonic, optical and thermal principles and demonstrates the potential of the techniques for a wide variety of applications concerning aircraft materials, especially aluminum and titanium alloys. The advantages and disadvantages of various techniques are evaluated.

Download or read book Nondestructive Characterization of Materials II written by Jean F. Bussière and published by Springer Science & Business Media. This book was released on 2013-03-14 with total page 750 pages. Available in PDF, EPUB and Kindle. Book excerpt: The possibility of nondestructively characterizing the microstruc ture, morphology or mechanical properties of materials is certainly a fascinating subject. In principle, such techniques can be used at all stages of a material's life - from the early stages of processing, to the end of a structural component's useful life. Interest in the subject thus arises not only from a purely scientific point of view but is also strongly motivated by economic pressures to improve productivity and quality in manufacturing, to insure the reliability and extend the life of existing structures. The present volume represents the edited papers presented at the Second International Symposium on the Nondestructive Characterization of Materials, held in Montreal, Canada, July 21-23, 1986. The Proceedings are divided into eight sections, which reflect the multidisciplinary nature of characterizing materials nondestructively: Polymers and Composites, Ceramics and Powder Metallurgy, Metals, Layered Structures/Adhesive Bonds/Welding, Degradation/Aging, Texture/ Anisotropy, Stress, and New Techniques. Invited papers by R. Hadcock of Grumman Aircraft Systems, R. Cannon of Rutgers University, H. Yada of Nippon Steel and R. Bridenbaugh of Alcoa review respectively the processing of polymer matrix composites, ceramics, steel and aluminum, emphasizing the need for material property sensors to improve process and quality control. Two other invited papers, one by A. Wedgwood of Harwell and the other by P. Holler of the IzFP in Saarbrucken review state of the art techniques to characterize particulate matter and metals respectively.

Download or read book Physical Ultrasonics of Composites written by Stanislav Rokhlin and published by Oxford University Press, USA. This book was released on 2011-03-03 with total page 401 pages. Available in PDF, EPUB and Kindle. Book excerpt: The objective of this book is to treat the behavior of ultrasonic waves as they interact with layered, anisotropic materials incorporating those structural aspects unique to composite laminates addressing both experimental and modeling methodologies. Anisotropic material interfaces, guided waves, waves in layered media and laminated plates are treated. The influence of finite-aperture transducers on electronic signals and the field of air-coupled ultrasonics end the work.

Download or read book Nonlinear Ultrasonic and Vibro Acoustical Techniques for Nondestructive Evaluation written by Tribikram Kundu and published by Springer. This book was released on 2018-10-19 with total page 761 pages. Available in PDF, EPUB and Kindle. Book excerpt: This multi-contributed volume provides a practical, applications-focused introduction to nonlinear acoustical techniques for nondestructive evaluation. Compared to linear techniques, nonlinear acoustical/ultrasonic techniques are much more sensitive to micro-cracks and other types of small distributed damages. Most materials and structures exhibit nonlinear behavior due to the formation of dislocation and micro-cracks from fatigue or other types of repetitive loadings well before detectable macro-cracks are formed. Nondestructive evaluation (NDE) tools that have been developed based on nonlinear acoustical techniques are capable of providing early warnings about the possibility of structural failure before detectable macro-cracks are formed. This book presents the full range of nonlinear acoustical techniques used today for NDE. The expert chapters cover both theoretical and experimental aspects, but always with an eye towards applications. Unlike other titles currently available, which treat nonlinearity as a physics problem and focus on different analytical derivations, the present volume emphasizes NDE applications over detailed analytical derivations. The introductory chapter presents the fundamentals in a manner accessible to anyone with an undergraduate degree in Engineering or Physics and equips the reader with all of the necessary background to understand the remaining chapters. This self-contained volume will be a valuable reference to graduate students through practising researchers in Engineering, Materials Science, and Physics. Represents the first book on nonlinear acoustical techniques for NDE applications Emphasizes applications of nonlinear acoustical techniques Presents the fundamental physics and mathematics behind nonlinear acoustical phenomenon in a simple, easily understood manner Covers a variety of popular NDE techniques based on nonlinear acoustics in a single volume

Download or read book Ultrasound in Food Processing written by Mar Villamiel and published by John Wiley & Sons. This book was released on 2017-04-25 with total page 764 pages. Available in PDF, EPUB and Kindle. Book excerpt: Part I: Fundamentals of ultrasound This part will cover the main basic principles of ultrasound generation and propagation and those phenomena related to low and high intensity ultrasound applications. The mechanisms involved in food analysis and process monitoring and in food process intensification will be shown. Part II: Low intensity ultrasound applications Low intensity ultrasound applications have been used for non-destructive food analysis as well as for process monitoring. Ultrasonic techniques, based on velocity, attenuation or frequency spectrum analysis, may be considered as rapid, simple, portable and suitable for on-line measurements. Although industrial applications of low-intensity ultrasound, such as meat carcass evaluation, have been used in the food industry for decades, this section will cover the most novel applications, which could be considered as highly relevant for future application in the food industry. Chapters addressing this issue will be divided into three subsections: (1) food control, (2) process monitoring, (3) new trends. Part III: High intensity ultrasound applications High intensity ultrasound application constitutes a way to intensify many food processes. However, the efficient generation and application of ultrasound is essential to achieving a successful effect. This part of the book will begin with a chapter dealing with the importance of the design of efficient ultrasonic application systems. The medium is essential to achieve efficient transmission, and for that reason the particular challenges of applying ultrasound in different media will be addressed. The next part of this section constitutes an up-to-date vision of the use of high intensity ultrasound in food processes. The chapters will be divided into four sections, according to the medium in which the ultrasound vibration is transmitted from the transducers to the product being treated. Thus, solid, liquid, supercritical and gas media have been used for ultrasound propagation. Previous books addressing ultrasonic applications in food processing have been based on the process itself, so chapters have been divided in mass and heat transport, microbial inactivation, etc. This new book will propose a revolutionary overview of ultrasonic applications based on (in the authors’ opinion) the most relevant factor affecting the efficiency of ultrasound applications: the medium in which ultrasound is propagated. Depending on the medium, ultrasonic phenomena can be completely different, but it also affects the complexity of the ultrasonic generation, propagation and application. In addition, the effect of high intensity ultrasound on major components of food, such as proteins, carbohydrates and lipids will be also covered, since this type of information has not been deeply studied in previous books. Other aspects related to the challenges of food industry to incorporate ultrasound devices will be also considered. This point is also very important since, in the last few years, researchers have made huge efforts to integrate fully automated and efficient ultrasound systems to the food production lines but, in some cases, it was not satisfactory. In this sense, it is necessary to identify and review the main related problems to efficiently produce and transmit ultrasound, scale-up, reduce cost, save energy and guarantee the production of safe, healthy and high added value foods.

Download or read book Applications on Ultrasonic Wave written by Jaesun Lee and published by MDPI. This book was released on 2021-09-02 with total page 112 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book presents applications on the ultrasonic wave for material characterization and nondestructive evaluations. It could be of interest to the researchers and students who are studying on the fields of ultrasonic waves.