Download or read book Topology Optimization Based on Morphing Mesh for Simultaneous Component Relocation and Frame Structure Design written by Mahsan Bakhtiarinejad and published by . This book was released on 2015 with total page 174 pages. Available in PDF, EPUB and Kindle. Book excerpt: This thesis research proposes a new topology optimization method based on morphing mesh (TOMM) technique in order to determine the optimal layout of components as well as the frame structure. In this method, two types of design variablesmorphing design variables and topology design variablesare defined for simultaneous design optimization of the components relocation and frame structure topology. Component relocation is enabled using FE Morphing approach, implemented by HyperMesh, on the basis of the SIMP method for compliance minimization of frame structure. Three design cases are studied using TOMM method: a simple cantilever beam design and two aircraft wing designs. The prevalent cantilever beam with a nodal force in the middle of the free end is studied to validate the proposed design methodology. Aircraft wing design cases are intended to obtain the best conceptual design by determining optimal placement of various subsystemscontrol system (flight control, engine control), fuel system, hydraulic system, and structural systemand the supporting frame structure. An advanced systematic design approach is needed for effective packaging of multiple subsystems while satisfying load-carrying performance and minimizing weight for energy efficiency. In the first wing design case, additional constraint on maintaining the weight balance is included and the corresponding design sensitivity is formulated. Then this wing design strategy is extensively applied to the commercial Boeing 757 aircraft wing where TOMM method is combined with the genetic algorithm for global search on component locations. The benefit of using the global search algorithm (genetic algorithm) is discussed in terms of high possibility on finding a global optimum and independency of initial design guess. The results of the TOMM method for simultaneous design optimization of components layout and structural topology have been compared to the classical structural topology optimization without component relocation. It has been proved that the inclusion of component relocation can improve structural performance. The proposed TOMM method will provide innovative design insight for complex modern multi-component structure.
Download or read book International Conference on Advanced Materials Modern Manufacturing and Computerized Automation IAMMCA written by Shanmugam Thillikkani and published by Trans Tech Publications Ltd. This book was released on 2024-04-30 with total page 128 pages. Available in PDF, EPUB and Kindle. Book excerpt: Selected peer-reviewed extended articles based on abstracts presented at the International conference on Advanced Materials, Modern Manufacturing and Computerized Automation (IAMMCA-2023) Aggregated Book
Download or read book Processing and Application of Engineering Materials written by Bruno Castanie and published by Trans Tech Publications Ltd. This book was released on 2024-04-18 with total page 172 pages. Available in PDF, EPUB and Kindle. Book excerpt: Special topic volume with invited peer-reviewed papers only
Download or read book Morphing Wing Technologies written by Sergio Ricci and published by Butterworth-Heinemann. This book was released on 2017-10-27 with total page 970 pages. Available in PDF, EPUB and Kindle. Book excerpt: Morphing Wings Technologies: Large Commercial Aircraft and Civil Helicopters offers a fresh look at current research on morphing aircraft, including industry design, real manufactured prototypes and certification. This is an invaluable reference for students in the aeronautics and aerospace fields who need an introduction to the morphing discipline, as well as senior professionals seeking exposure to morphing potentialities. Practical applications of morphing devices are presented—from the challenge of conceptual design incorporating both structural and aerodynamic studies, to the most promising and potentially flyable solutions aimed at improving the performance of commercial aircraft and UAVs. Morphing aircraft are multi-role aircraft that change their external shape substantially to adapt to a changing mission environment during flight. The book consists of eight sections as well as an appendix which contains both updates on main systems evolution (skin, structure, actuator, sensor, and control systems) and a survey on the most significant achievements of integrated systems for large commercial aircraft. Provides current worldwide status of morphing technologies, the industrial development expectations, and what is already available in terms of flying systems Offers new perspectives on wing structure design and a new approach to general structural design Discusses hot topics such as multifunctional materials and auxetic materials Presents practical applications of morphing devices
Download or read book Shape Optimization Problems written by Hideyuki Azegami and published by Springer Nature. This book was released on 2020-09-30 with total page 646 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book provides theories on non-parametric shape optimization problems, systematically keeping in mind readers with an engineering background. Non-parametric shape optimization problems are defined as problems of finding the shapes of domains in which boundary value problems of partial differential equations are defined. In these problems, optimum shapes are obtained from an arbitrary form without any geometrical parameters previously assigned. In particular, problems in which the optimum shape is sought by making a hole in domain are called topology optimization problems. Moreover, a problem in which the optimum shape is obtained based on domain variation is referred to as a shape optimization problem of domain variation type, or a shape optimization problem in a limited sense. Software has been developed to solve these problems, and it is being used to seek practical optimum shapes. However, there are no books explaining such theories beginning with their foundations. The structure of the book is shown in the Preface. The theorems are built up using mathematical results. Therefore, a mathematical style is introduced, consisting of definitions and theorems to summarize the key points. This method of expression is advanced as provable facts are clearly shown. If something to be investigated is contained in the framework of mathematics, setting up a theory using theorems prepared by great mathematicians is thought to be an extremely effective approach. However, mathematics attempts to heighten the level of abstraction in order to understand many things in a unified fashion. This characteristic may baffle readers with an engineering background. Hence in this book, an attempt has been made to provide explanations in engineering terms, with examples from mechanics, after accurately denoting the provable facts using definitions and theorems.
Download or read book Computational Optimization Methods and Algorithms written by Slawomir Koziel and published by Springer. This book was released on 2011-06-17 with total page 292 pages. Available in PDF, EPUB and Kindle. Book excerpt: Computational optimization is an important paradigm with a wide range of applications. In virtually all branches of engineering and industry, we almost always try to optimize something - whether to minimize the cost and energy consumption, or to maximize profits, outputs, performance and efficiency. In many cases, this search for optimality is challenging, either because of the high computational cost of evaluating objectives and constraints, or because of the nonlinearity, multimodality, discontinuity and uncertainty of the problem functions in the real-world systems. Another complication is that most problems are often NP-hard, that is, the solution time for finding the optimum increases exponentially with the problem size. The development of efficient algorithms and specialized techniques that address these difficulties is of primary importance for contemporary engineering, science and industry. This book consists of 12 self-contained chapters, contributed from worldwide experts who are working in these exciting areas. The book strives to review and discuss the latest developments concerning optimization and modelling with a focus on methods and algorithms for computational optimization. It also covers well-chosen, real-world applications in science, engineering and industry. Main topics include derivative-free optimization, multi-objective evolutionary algorithms, surrogate-based methods, maximum simulated likelihood estimation, support vector machines, and metaheuristic algorithms. Application case studies include aerodynamic shape optimization, microwave engineering, black-box optimization, classification, economics, inventory optimization and structural optimization. This graduate level book can serve as an excellent reference for lecturers, researchers and students in computational science, engineering and industry.
Download or read book IUTAM Symposium on Topological Design Optimization of Structures Machines and Materials written by Martin Philip Bendsoe and published by Springer Science & Business Media. This book was released on 2006-10-03 with total page 602 pages. Available in PDF, EPUB and Kindle. Book excerpt: This volume offers edited papers presented at the IUTAM-Symposium Topological design optimization of structures, machines and materials - status and perspectives, October 2005. The papers cover the application of topological design optimization to fluid-solid interaction problems, acoustics problems, and to problems in biomechanics, as well as to other multiphysics problems. Also in focus are new basic modelling paradigms, covering new geometry modelling such as level-set methods and topological derivatives.
Download or read book Smart Intelligent Aircraft Structures SARISTU written by Piet Christof Wölcken and published by Springer. This book was released on 2015-09-04 with total page 1025 pages. Available in PDF, EPUB and Kindle. Book excerpt: The book includes the research papers presented in the final conference of the EU funded SARISTU (Smart Intelligent Aircraft Structures) project, held at Moscow, Russia between 19-21 of May 2015. The SARISTU project, which was launched in September 2011, developed and tested a variety of individual applications as well as their combinations. With a strong focus on actual physical integration and subsequent material and structural testing, SARISTU has been responsible for important progress on the route to industrialization of structure integrated functionalities such as Conformal Morphing, Structural Health Monitoring and Nanocomposites. The gap- and edge-free deformation of aerodynamic surfaces known as conformal morphing has gained previously unrealized capabilities such as inherent de-icing, erosion protection and lightning strike protection, while at the same time the technological risk has been greatly reduced. Individual structural health monitoring techniques can now be applied at the part-manufacturing level rather than via extending an aircraft’s time in the final assembly line. And nanocomposites no longer lose their improved properties when trying to upscale from neat resin testing to full laminate testing at element level. As such, this book familiarizes the reader with the most significant develo pments, achievements and key technological steps which have been made possible through the four-year long cooperation of 64 leading entities from 16 different countries with the financial support of the European Commission.
Download or read book Polygon Mesh Processing written by Mario Botsch and published by CRC Press. This book was released on 2010-10-07 with total page 244 pages. Available in PDF, EPUB and Kindle. Book excerpt: Geometry processing, or mesh processing, is a fast-growing area of research that uses concepts from applied mathematics, computer science, and engineering to design efficient algorithms for the acquisition, reconstruction, analysis, manipulation, simulation, and transmission of complex 3D models. Applications of geometry processing algorithms already cover a wide range of areas from multimedia, entertainment, and classical computer-aided design, to biomedical computing, reverse engineering, and scientific computing. Over the last several years, triangle meshes have become increasingly popular, as irregular triangle meshes have developed into a valuable alternative to traditional spline surfaces. This book discusses the whole geometry processing pipeline based on triangle meshes. The pipeline starts with data input, for example, a model acquired by 3D scanning techniques. This data can then go through processes of error removal, mesh creation, smoothing, conversion, morphing, and more. The authors detail techniques for those processes using triangle meshes. A supplemental website contains downloads and additional information.
Download or read book Airborne Wind Energy written by Roland Schmehl and published by Springer. This book was released on 2018-03-31 with total page 752 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book provides in-depth coverage of the latest research and development activities concerning innovative wind energy technologies intended to replace fossil fuels on an economical basis. A characteristic feature of the various conversion concepts discussed is the use of tethered flying devices to substantially reduce the material consumption per installed unit and to access wind energy at higher altitudes, where the wind is more consistent. The introductory chapter describes the emergence and economic dimension of airborne wind energy. Focusing on “Fundamentals, Modeling & Simulation”, Part I includes six contributions that describe quasi-steady as well as dynamic models and simulations of airborne wind energy systems or individual components. Shifting the spotlight to “Control, Optimization & Flight State Measurement”, Part II combines one chapter on measurement techniques with five chapters on control of kite and ground stations, and two chapters on optimization. Part III on “Concept Design & Analysis” includes three chapters that present and analyze novel harvesting concepts as well as two chapters on system component design. Part IV, which centers on “Implemented Concepts”, presents five chapters on established system concepts and one chapter about a subsystem for automatic launching and landing of kites. In closing, Part V focuses with four chapters on “Technology Deployment” related to market and financing strategies, as well as on regulation and the environment. The book builds on the success of the first volume “Airborne Wind Energy” (Springer, 2013), and offers a self-contained reference guide for researchers, scientists, professionals and students. The respective chapters were contributed by a broad variety of authors: academics, practicing engineers and inventors, all of whom are experts in their respective fields.
Download or read book Shape Optimization by the Homogenization Method written by Gregoire Allaire and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 470 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book provides an introduction to the theory and numerical developments of the homogenization method. It's main features are: a comprehensive presentation of homogenization theory; an introduction to the theory of two-phase composite materials; a detailed treatment of structural optimization by using homogenization; a complete discussion of the resulting numerical algorithms with many documented test problems. It will be of interest to researchers, engineers, and advanced graduate students in applied mathematics, mechanical engineering, and structural optimization.
Download or read book Advances in Structural and Multidisciplinary Optimization written by Axel Schumacher and published by Springer. This book was released on 2017-12-04 with total page 2101 pages. Available in PDF, EPUB and Kindle. Book excerpt: The volume includes papers from the WSCMO conference in Braunschweig 2017 presenting research of all aspects of the optimal design of structures as well as multidisciplinary design optimization where the involved disciplines deal with the analysis of solids, fluids or other field problems. Also presented are practical applications of optimization methods and the corresponding software development in all branches of technology.
Download or read book Representations and Techniques for 3D Object Recognition and Scene Interpretation written by Derek Hoiem and published by Morgan & Claypool Publishers. This book was released on 2011 with total page 172 pages. Available in PDF, EPUB and Kindle. Book excerpt: One of the grand challenges of artificial intelligence is to enable computers to interpret 3D scenes and objects from imagery. This book organizes and introduces major concepts in 3D scene and object representation and inference from still images, with a focus on recent efforts to fuse models of geometry and perspective with statistical machine learning. The book is organized into three sections: (1) Interpretation of Physical Space; (2) Recognition of 3D Objects; and (3) Integrated 3D Scene Interpretation. The first discusses representations of spatial layout and techniques to interpret physical scenes from images. The second section introduces representations for 3D object categories that account for the intrinsically 3D nature of objects and provide robustness to change in viewpoints. The third section discusses strategies to unite inference of scene geometry and object pose and identity into a coherent scene interpretation. Each section broadly surveys important ideas from cognitive science and artificial intelligence research, organizes and discusses key concepts and techniques from recent work in computer vision, and describes a few sample approaches in detail. Newcomers to computer vision will benefit from introductions to basic concepts, such as single-view geometry and image classification, while experts and novices alike may find inspiration from the book's organization and discussion of the most recent ideas in 3D scene understanding and 3D object recognition. Specific topics include: mathematics of perspective geometry; visual elements of the physical scene, structural 3D scene representations; techniques and features for image and region categorization; historical perspective, computational models, and datasets and machine learning techniques for 3D object recognition; inferences of geometrical attributes of objects, such as size and pose; and probabilistic and feature-passing approaches for contextual reasoning about 3D objects and scenes. Table of Contents: Background on 3D Scene Models / Single-view Geometry / Modeling the Physical Scene / Categorizing Images and Regions / Examples of 3D Scene Interpretation / Background on 3D Recognition / Modeling 3D Objects / Recognizing and Understanding 3D Objects / Examples of 2D 1/2 Layout Models / Reasoning about Objects and Scenes / Cascades of Classifiers / Conclusion and Future Directions
Download or read book Topology Optimization in Structural Mechanics written by G.I.N. Rozvany and published by Springer. This book was released on 2014-05-04 with total page 325 pages. Available in PDF, EPUB and Kindle. Book excerpt: Topology optimization is a relatively new and rapidly expanding field of structural mechanics. It deals with some of the most difficult problems of mechanical sciences but it is also of considerable practical interest, because it can achieve much greater savings than mere cross-section or shape optimization.
Download or read book Optimum Structural Design written by Richard H. Gallagher and published by John Wiley & Sons. This book was released on 1973 with total page 380 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Adaptive Structures written by David Wagg and published by John Wiley & Sons. This book was released on 2008-04-09 with total page 314 pages. Available in PDF, EPUB and Kindle. Book excerpt: Adaptive structures have the ability to adapt, evolve or change their properties or behaviour in response to the environment around them. The analysis and design of adaptive structures requires a highly multi-disciplinary approach which includes elements of structures, materials, dynamics, control, design and inspiration taken from biological systems. Development of adaptive structures has been taking place in a wide range of industrial applications, but is particularly advanced in the aerospace and space technology sector with morphing wings, deployable space structures; piezoelectric devices and vibration control of tall buildings. Bringing together some of the foremost world experts in adaptive structures, this unique text: includes discussions of the application of adaptive structures in the aerospace, military, civil engineering structures, automotive and MEMS. presents the impact of biological inspiration in designing adaptive structures, particularly the use of hierarchy in nature, which typically induces multi-functional behavior. sets the agenda for future research in adaptive structures in one distinctive single volume. Adaptive Structures: Engineering Applications is essential reading for engineers and scientists working in the fields of intelligent materials, structural vibration, control and related smart technologies. It will also be of interest to senior undergraduate and postgraduate research students as well as design engineers working in the aerospace, mechanical, electrical and civil engineering sectors.
Download or read book The Algorithm Design Manual written by Steven S Skiena and published by Springer Science & Business Media. This book was released on 2009-04-05 with total page 742 pages. Available in PDF, EPUB and Kindle. Book excerpt: This newly expanded and updated second edition of the best-selling classic continues to take the "mystery" out of designing algorithms, and analyzing their efficacy and efficiency. Expanding on the first edition, the book now serves as the primary textbook of choice for algorithm design courses while maintaining its status as the premier practical reference guide to algorithms for programmers, researchers, and students. The reader-friendly Algorithm Design Manual provides straightforward access to combinatorial algorithms technology, stressing design over analysis. The first part, Techniques, provides accessible instruction on methods for designing and analyzing computer algorithms. The second part, Resources, is intended for browsing and reference, and comprises the catalog of algorithmic resources, implementations and an extensive bibliography. NEW to the second edition: • Doubles the tutorial material and exercises over the first edition • Provides full online support for lecturers, and a completely updated and improved website component with lecture slides, audio and video • Contains a unique catalog identifying the 75 algorithmic problems that arise most often in practice, leading the reader down the right path to solve them • Includes several NEW "war stories" relating experiences from real-world applications • Provides up-to-date links leading to the very best algorithm implementations available in C, C++, and Java
