Download or read book Thermal Fatigue Behavior and Strength Estimation of Power Plant Component Materials Under Creep fatigue Interaction written by and published by . This book was released on 1978 with total page 36 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Thermal fatigue behavior and strength estimation of power plant component materials under creep fatigue interaction written by Kazuo Kuwahara and published by . This book was released on 1978 with total page 36 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Thermal Fatigue Nehavior and Strength Estimation of Power Plant Component Materials Under Creep fatigue Interaction written by Kazuo Kuwahara and published by . This book was released on 1978 with total page 36 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Thermomechanical Fatigue Behavior of Materials written by Huseyin Sehitoglu and published by ASTM International. This book was released on 1993 with total page 259 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Thermal Fatigue of Materials and Components written by David A. Spera and published by ASTM International. This book was released on 1976 with total page 271 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Ability of the Total Strain Version of Strainrange Partitioning to Characterize Thermomechanical Fatigue Behavior written by James F. Saltsman and published by . This book was released on 1994 with total page 28 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book High Temperature Fatigue written by R.P. Skelton and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 330 pages. Available in PDF, EPUB and Kindle. Book excerpt: About 35 years ago, thermal fatigue was identified as an important phenomenon which limited the lifetime of high temperature plant. In the intervening years many investigations have been carried out, primarily to give guidance on likely endurance (especially in the presence of time dependent deformation) but latterly, with the introduction of sophisticated testing machines, to provide knowledge of the underlying mechanisms of failure. A previous edited book (Fatigue at High Temperature, Elsevier Applied Science Publishers, 1983) summarised the state-of-the-art of high temperature fatigue testing and examined the factors influencing life, such as stress state, environment and microstructural effects. It also considered, in some detail, cyclic crack growth as a more rigorous approach to life limitation. The aim of the present volume (which in style and format follows exactly the same lines as its predecessor) is once again to pursue the desire to translate detailed laboratory knowledge into engineering design and assessment. There is, for example, a need to consider the limitations of the laboratory specimen and its relationship with engineering features. Many design procedures still rely on a simple endurance approach based on failure of a smooth specimen, and this is taken to indicate crack initiation in the component. In this volume, therefore, crack propagation is covered only incidentally, emphasis being placed instead on basic cyclic stress strain properties, non-isothermal behaviour, metallography, failure criteria and the need for agreed testing procedures.

Download or read book Creep Fatigue Behavior of Creep Strength Enhanced Ferritic Steels written by Jonathan Parker and published by . This book was released on 2011 with total page 11 pages. Available in PDF, EPUB and Kindle. Book excerpt: Creep Fatigue knowledge is necessary for meaningful reliability assessment of existing power generating plant because cyclic operation of an aging power plant fleet requires better understanding of factors affecting damage initiation and propagation, as well as technologies and methods to predict damage accumulation for individual components and overall safe/economic life. Utilities typically adopt operating practices which involve more severe cycles, either in terms of number or magnitude or both, so that there is, and will continue to be, a requirement to assess the creep fatigue performance of traditional boiler and turbine components. The recent installation of large numbers of combustion turbines and the associated heat recovery steam generators has significantly increased the number of materials and components which are operating under cyclic conditions at high temperatures. Indeed, the materials and component types susceptible to creep-fatigue is increasing since much of the new high efficiency coal plant will be operating with steam/metal temperatures much higher than those of traditional plant. Recent expert review has reemphasized that with most practical scenarios regarding future generation mix, fossil plant will continue to be important. Thus, there is the expectation that creep-fatigue damage will increase in occurrence, and affect an increased range of components. Different challenges will be faced since the new components will involve a greater range of alloys, methods of manufacture, and types of operation than conventional fossil generating stations. It is therefore apparent that operation under cyclic conditions at temperatures where creep can occur the potential for creep/fatigue damage is, and will continue to be, a matter of significant concern. The present paper considers specific challenges associated with creep/fatigue in creep strength enhanced ferritic steels such as Grade 91 and Grade 92.

Download or read book Creep fatigue damage in power plant materials Part 2 The behavior of elevated temperature low cycle fatigue crack initiation and propagation written by and published by . This book was released on 1982 with total page 42 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Thermomechanical fatigue behavior of materials written by Michael J. Verrilli and published by ASTM International. This book was released on 1996 with total page 382 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Creep and Fracture in High Temperature Components written by European Creep Collaborative Committee and published by DEStech Publications, Inc. This book was released on 2005 with total page 1136 pages. Available in PDF, EPUB and Kindle. Book excerpt: Provides information from around the world on creep in multiple high-temperature metals, alloys, and advanced materials.

Download or read book Damage Mechanisms and Life Assessment of High Temperature Components written by Ramaswamy Viswanathan and published by ASM International. This book was released on 1989 with total page 497 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Prediction of thermal fatigue life in high temperature component materials for power plant written by and published by . This book was released on 1983 with total page 27 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Proceedings Creep Fracture in High Temperature Components written by I. A. Shibli and published by DEStech Publications, Inc. This book was released on 2009 with total page 661 pages. Available in PDF, EPUB and Kindle. Book excerpt: A compendium of European and worldwide research investigating creep, fatigue and failure behaviors in metals under high-temperature and other service stresses. It helps set the standards for coordinating creep data and for maintaining defect-free quality in high-temperature metals and metal-based weldments.

Download or read book Scientific and Technical Aerospace Reports written by and published by . This book was released on with total page 994 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book STAR written by and published by . This book was released on 1973 with total page 904 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book ASM Specialty Handbook written by Joseph R. Davis and published by ASM International. This book was released on 1997-01-01 with total page 608 pages. Available in PDF, EPUB and Kindle. Book excerpt: Materials covered include carbon, alloy and stainless steels; alloy cast irons; high-alloy cast steels; superalloys; titanium and titanium alloys; refractory metals and alloys; nickel-chromium and nickel-thoria alloys; structural intermetallics; structural ceramics, cermets, and cemented carbides; and carbon-composites.