Download or read book The Temperature Field of a Turbine Blade with Transverse Air Cooling written by I. S. Lyubchenko and published by . This book was released on 1969 with total page 10 pages. Available in PDF, EPUB and Kindle. Book excerpt: The cross section of a turbine blade with a deflector in a uniform gas flow is examined. The cooling air, entering near the root section within the deflector, passes through the slits at the leading edge of the deflector. It then breaks into branches and flows through transverse channels over concave and convex surfaces. Air consumption for cooling the back edge and trough is noted along the blade length. The stagnation temperature of the gas in the boundary layer over the profile and the blade temperature over the wall thickness are considered. The balance equations for a blade element and the air flowing past the element are equated.
Download or read book Determining the Temperature Field of Turbine Blades with Longitudinal Air Cooling on the Basis of Asymptotic Methods of Analysis written by I. S. Lyubchenko and published by . This book was released on 1966 with total page 15 pages. Available in PDF, EPUB and Kindle. Book excerpt: After citing several sources given different methods for calculating the temperature condition of a gas turbine rotor blade, the author concludes that, on the whole, the problem of temperature distribution along the rotor blade height, considering the variation of all factors entering into the system of differential equations describing the phenomenon of heat-exchange, remained unsolved. In the present paper, according to the author, the given problem is approximately solved using asymptotic methods for the most general case, whereby the error of actual relationships of the quantities entering into the system of equations does not exceed 1--3%.
Download or read book Measurements of Heat Transfer Flow and Pressures in a Simulated Turbine Blade Internal Cooling Passage written by Louis M. Russell and published by . This book was released on 1997 with total page 30 pages. Available in PDF, EPUB and Kindle. Book excerpt: An experimental study was made to obtain quantitative information on heat transfer, flow, and pressure distribution in a branched duct test section that had several significant features of an internal cooling passage of a turbine blade. The objective of this study was to generate a set of experimental data that could be used for validation of computer codes that would be used to model internal cooling. Surface heat transfer coefficients and entrance flow conditions were measured at nominal entrance Reynolds numbers of 45 000, 335 000, and 726 000. Heat transfer data were obtained by using a steady-state technique in which an Inconel heater sheet is attached to the surface and coated with liquid crystals. Visual and quantitative flow-field data from particle image velocimetry measurements for a plane at midchannel height for a Reynolds number of 45 000 were also obtained. The flow was seeded with polystyrene particles and illuminated by a laser light sheet. Pressure distribution measurements were made both on the surface with discrete holes and in the flow field with a total pressure probe. The flow-field measurements yielded flow-field velocities at selected locations. A relatively new method, pressure sensitive paint, was also used to measure surface pressure distribution. The pressure paint data obtained at Reynolds numbers of 335 000 and 726 000 compared well with the more standard method of measuring pressures by using discrete holes.
Download or read book Temperatures and Stresses on Hollow Blades for Gas Turbines written by Erich Pollman and published by . This book was released on 1947 with total page 600 pages. Available in PDF, EPUB and Kindle. Book excerpt: The present treatise reports on theoretical investigations and test-stand measurements which were carried out in the BMW Flugmotoren GMbH in developing the hollow blade for exhaust gas turbines. As an introduction the temperature variation and the stress on a turbine blade for a gas temperature of 900 degrees and circumferential velocities of 600 meters per second are discussed. The assumptions onthe heat transfer coefficients at the blade profile are supported by tests on an electrically heated blade model. The temperature distribution in the cross section of a blade Is thoroughly investigated and the temperature field determined for a special case. A method for calculation of the thermal stresses in turbine blades for a given temperature distribution is indicated. The effect of the heat radiation on the blade temperature also is dealt with. Test-stand experiments on turbine blades are evaluated, particularly with respect to temperature distribution in the cross section; maximum and minimum temperature in the cross section are ascertained. Finally, the application of the hollow blade for a stationary gas turbine is investigated. Starting from a setup for 550 C gas temperature the improvement of the thermal efficiency and the fuel consumption are considered as well as the increase of the useful power by use of high temperatures. The power required for blade cooling is taken into account.
Download or read book Scientific and Technical Aerospace Reports written by and published by . This book was released on 1995 with total page 542 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Analytical and Experimental Investigation of a Forced convection Air cooled Internal Strut supported Turbine Blade written by Eugene F. Schum and published by . This book was released on 1954 with total page 32 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Procedure for Calculating Turbine Blade Temperatures and Comparison of Calculated with Observed Values for Two Stationary Air cooled Blades written by W. Byron Brown and published by . This book was released on 1952 with total page 44 pages. Available in PDF, EPUB and Kindle. Book excerpt: Abstract: Local and average blade temperatures were calculated for two stationary air-cooled turbine blades with 10 tubes and 13 fins forming the internal heat-transfer surfaces. These temperatures were calculated using previously published NACA temperature-distribution equations and the most recent theories for determining heat-transfer coefficients, including for the first time the allowance for effects of variable wall temperature on gas-to-blade heat-transfer coefficients at the leading and trailing sections of turbine blades. Comparison of calculated and experimental blade temperatures, for gas temperatures of 300° and 1000°F, resulted in good agreement.
Download or read book Effect of Chord Size on Weight and Cooling Characteristics of Air cooled Turbine Blades written by Jack B. Esgar and published by . This book was released on 1957 with total page 44 pages. Available in PDF, EPUB and Kindle. Book excerpt: An analysis has been made to determine the effect of chord size on the weight and cooling characteristics of shell-supported, air-cooled gas-turbine blades. In uncooled turbines with solid blades, the general practice has been to design turbines with high aspect ratio (small blade chord) to achieve substantial turbine weight reduction. With air-cooled blades, this study shows that turbine blade weight is affected to a much smaller degree by the size of the blade chord.
Download or read book Gas Turbine Blade Cooling written by Chaitanya D Ghodke and published by SAE International. This book was released on 2018-12-10 with total page 238 pages. Available in PDF, EPUB and Kindle. Book excerpt: Gas turbines play an extremely important role in fulfilling a variety of power needs and are mainly used for power generation and propulsion applications. The performance and efficiency of gas turbine engines are to a large extent dependent on turbine rotor inlet temperatures: typically, the hotter the better. In gas turbines, the combustion temperature and the fuel efficiency are limited by the heat transfer properties of the turbine blades. However, in pushing the limits of hot gas temperatures while preventing the melting of blade components in high-pressure turbines, the use of effective cooling technologies is critical. Increasing the turbine inlet temperature also increases heat transferred to the turbine blade, and it is possible that the operating temperature could reach far above permissible metal temperature. In such cases, insufficient cooling of turbine blades results in excessive thermal stress on the blades causing premature blade failure. This may bring hazards to the engine's safe operation. Gas Turbine Blade Cooling, edited by Dr. Chaitanya D. Ghodke, offers 10 handpicked SAE International's technical papers, which identify key aspects of turbine blade cooling and help readers understand how this process can improve the performance of turbine hardware.
Download or read book The Unsteady Temperature Field in a Turbine Blade Cooling Channel written by T. Arts and published by . This book was released on 2001 with total page 13 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Experimental Investigation of Air cooled Turbine Blades in Turbojet Engine written by Herman H. Ellerbrock (Jr.) and published by . This book was released on 1951 with total page 78 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book U S Government Research Development Reports written by and published by . This book was released on 1970 with total page 232 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Survey of Advantages and Problems Associated with Transpiration Cooling and Film Cooling of Gas turbine Blades written by Ernst Rudolf Georg Eckert and published by . This book was released on 1951 with total page 44 pages. Available in PDF, EPUB and Kindle. Book excerpt: Summary: Transpiration and film cooling promise to be effective methods of cooling gas-turbine blades; consequently, analytical and experimental investigations are being conducted to obtain a better understanding of these processes. This report serves as an introduction to these cooling methods, explains the physical processes, and surveys the information available for predicting blade temperatures and heat-transfer rates. In addition, the difficulties encountered in obtaining a uniform blade temperature are discussed, and the possibilities of correcting these difficulties are indicated. Air is the only coolant considered in the application of these cooling methods.
Download or read book Experimental and Analytical Investigation of Heat transfer Characteristics of a Return flow Air cooled Turbine Rotor Blade written by Francis S. Stepka and published by . This book was released on 1959 with total page 26 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Experimental Investigation of the Heat transfer Characteristics of an Air cooled Sintered Porous Turbine Blade written by Louis J. Schafer (Jr.) and published by . This book was released on 1952 with total page 38 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Space Engineering written by G.A. Partel and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 725 pages. Available in PDF, EPUB and Kindle. Book excerpt: The 2nd International Conference on Space Engineering took place May 7-10, 1969, at Venice, Italy, under the organization of the Centro Studi Trasporti Missilistici and the Association pour l'Etude et la Recherche Astronautique et Cosmique. Its purpose was to bring together those interested in the technological development of space components, to exchange information by the presentation of papers and to discuss present problems and future trends, and to this end forty-eight papers were presented by distinguished experts from all over the world. The papers were selected from as wide a background as possible, approximately an equal number coming from the academic and research establishments as from industry. The principal criterion for their selection was that they should contribute to the knowledge of Space Engineering, and have application either to the improve ment of current technologies or to the design of more advanced systems for the future. Six pertinent sessions were planned which covered the major areas of interest: (1) Structures and Materials, where three important papers were presented; (2) Guidance and Control Systems, in which six valuable papers were presented, in cluding problems of controlling space ships, details of the inertial guidance system of the ELDO launch vehicle, the attitude control system of the "Europa 2"; (3) Propellants and Combustion, where eleven papers described recent work on solid and liquid rocket engines, advanced fuels and oxidizers, effects of additives, propellant injection, propellant expulsion techniques; (4) Propulsion, in which session ten papers
Download or read book Heat Transfer in Gas Turbines written by Bengt Sundén and published by Witpress. This book was released on 2001 with total page 544 pages. Available in PDF, EPUB and Kindle. Book excerpt: This title presents and reflects current active research on various heat transfer topics and related phenomena in gas turbine systems. It begins with a general introduction to gas turbine heat transfer, before moving on to specific areas.
