Download or read book The Effect of O2 H2O and N2 on the Fatigue Crack Growth Behavior of an Alpha Beta Titanium Alloy at 24 C and 177 C written by Stephen W. Smith and published by . This book was released on 2001 with total page 34 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book The Effect of O2 H2o and N2 on the Fatigue Crack Growth Behavior of an Alpha Beta Titanium Alloy at 24 C and 177 C written by National Aeronautics and Space Adm Nasa and published by Independently Published. This book was released on 2018-09-17 with total page 34 pages. Available in PDF, EPUB and Kindle. Book excerpt: To study the effects of atmospheric species on the fatigue crack growth behavior of an a+B titanium alloy (Ti 6-2-2-2-2) at room temperature and 177 C, fatigue tests were performed in laboratory air, ultrahigh vacuum, and high purity water vapor, oxygen, nitrogen and helium at various partial pressures. Accelerated fatigue crack growth rates in laboratory air compared to ultrahigh vacuum are linked to the damaging effects of both water vapor and oxygen. Observations of the fatigue crack growth behavior in ultrahigh purity environments, along with surface film analysis using X-ray photoelectron spectroscopy (XPS), suggest that multiple crack-tip processes govern the damaging effects of air. Three possible mechanisms are proposed: 1) at low pressure (less than 10(exp -1) Pa), accelerated da/dN is likely due to monolayer adsorption on crack-tip surfaces presumably resulting in decreased bond strengths at the fatigue crack tip, 2) for pressures greater than 10(exp -1) Pa, accelerated da/dN in oxygen may result from oxidation at the crack tip limiting reversible slip, and 3) in water vapor, absorption of atomic hydrogen at the reactive crack tip resulting in process zone embrittlement.Smith, Stephen W. and Piascik, Robert S.Langley Research CenterFATIGUE TESTS; FATIGUE (MATERIALS); CRACK PROPAGATION; TITANIUM ALLOYS; EMBRITTLEMENT; ATMOSPHERIC COMPOSITION; X RAY SPECTROSCOPY; WATER VAPOR; ULTRAHIGH VACUUM; PHOTOELECTRON SPECTROSCOPY
Download or read book Chemical Abstracts written by and published by . This book was released on 2002 with total page 2676 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Threshold Fatigue Crack Growth Behavior written by F. K. Haake and published by . This book was released on 1989 with total page 120 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Fatigue Crack Growth Thresholds Endurance Limits and Design written by J. C. Newman and published by ASTM International. This book was released on 2000 with total page 436 pages. Available in PDF, EPUB and Kindle. Book excerpt: Annotation Contains 24 papers from the November, 1998 symposium of the same name, sponsored by the ASTM Committee E8 on Fatigue and Fracture, and presented by Newman and Piascik (both of the NASA Langley Research Center). The papers focus on such areas as fatigue-crack growth threshold mechanisms, loading and specimen-type effects, analyses of fatigue-crack-growth-threshold behavior, and applications of threshold concepts and endurance limits to aerospace and structural materials. Annotation copyrighted by Book News, Inc., Portland, OR.
Download or read book Fatigue Crack Growth Measurement and Data Analysis written by S. J. Hudak and published by ASTM International. This book was released on 1981 with total page 384 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Load Interaction Effects on Fatigue Crack Growth in Ti 6Al 4V Alloy written by Robert Peh-ying Wei and published by . This book was released on 1973 with total page 36 pages. Available in PDF, EPUB and Kindle. Book excerpt: The importance of delay, retardation in the rate of fatigue crack growth, produced by load interactions in variable amplitude loading, on the accurate prediction of fatigue lives of engineering structures is discussed. The effects of a broad range of loading variables on delay in fatigue crack growth at room temperature are examined for a mill annealed Ti-6Al-4V alloy. The results are used to estimate crack growth behavior under programmed loads.
Download or read book Micro and Macro Mechanics of Crack Growth written by K. Sadananda and published by . This book was released on 1982 with total page 264 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Fatigue Crack Propagation written by and published by . This book was released on 1967 with total page 570 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Titanium written by Matthew J. Donachie and published by ASM International. This book was released on 2000 with total page 381 pages. Available in PDF, EPUB and Kindle. Book excerpt: Designed to support the need of engineering, management, and other professionals for information on titanium by providing an overview of the major topics, this book provides a concise summary of the most useful information required to understand titanium and its alloys. The author provides a review of the significant features of the metallurgy and application of titanium and its alloys. All technical aspects of the use of titanium are covered, with sufficient metals property data for most users. Because of its unique density, corrosion resistance, and relative strength advantages over competing materials such as aluminum, steels, and superalloys, titanium has found a niche in many industries. Much of this use has occurred through military research, and subsequent applications in aircraft, of gas turbine engines, although more recent use features replacement joints, golf clubs, and bicycles.Contents include: A primer on titanium and its alloys, Introduction to selection of titanium alloys, Understanding titanium's metallurgy and mill products, Forging and forming, Castings, Powder metallurgy, Heat treating, Joining technology and practice, Machining, Cleaning and finishing, Structure/processing/property relationships, Corrosion resistance, Advanced alloys and future directions, Appendices: Summary table of titanium alloys, Titanium alloy datasheets, Cross-reference to titanium alloys, Listing of selected specification and standardization organizations, Selected manufacturers, suppliers, services, Corrosion data, Machining data.
Download or read book Fretting Fatigue Behavior of the Titanium Alloy Ti 6AL 4V Under Seawater Conditions written by Lewis C. Lietch and published by . This book was released on 2004-03-01 with total page 129 pages. Available in PDF, EPUB and Kindle. Book excerpt: The fretting fatigue behavior of Ti-6A1-4V was investigated in laboratory air and under a controlled environment consisting of synthetic seawater. Fretting fatigue tests were performed for both low and high cycle fatigue regimes. Finite element analysis was utilized to model and analyze the experimental data. The applied stress range and the Modified Shear Stress Range were evaluated as potential fatigue parameters. The results found from this study can be summarized as: (1) seawater had a deleterious effect on fretting fatigue life in the low cycle fatigue regime but improved life in the high cycle fatigue regime, (2) although the Q/P ratio for both conditions increased with an increasing applied stress, the difference between the two conditions was negligible, (3) debris from dry samples contained titanium and oxides while the debris from seawater samples contained titanium, oxides, and seawater contaminants, (4) fretting scar volume was larger under seawater conditions than dry conditions, (5) there were more, closely spaced striations on the fracture surface of the dry samples than of the seawater samples, and (6) both the applied (far field) stress range and the Modified Shear Stress Range can potentially be used as conservative fretting fatigue parameters under high cycle fatigue conditions.
Download or read book Short crack Growth Behaviour in Various Aircraft Materials written by and published by . This book was released on 1990 with total page 196 pages. Available in PDF, EPUB and Kindle. Book excerpt: AGARD Report R-732 reviews the results of the first phase of an AGARD Cooperative Test Programme on the behaviour and growth of "short" fatigue cracks. That report describes the establishment of a common test method, means of data collection/analysis and crack growth modelling in an aircraft alloy AA2024-T3. The second and concluding phase of this Programme allowed participants to test various materials and loading conditions. The results of this second phase are described in this report. All materials exhibited a "short-crack" effect to some extent. The effect was much less evident in 4340 steel than in the other materials. For the aluminium, aluminium-lithium and titanium alloys, short cracks grew at stress-intensity factor ranges lower, in some cases much lower, than the thresholds obtained from long crack tests. Several laboratories used the same crack growth model to analyze the growth of short cracks. Reasonable agreement was found between measured and predicted short-crack growth rates and fatigue lives.
Download or read book Aerospace Materials and Applications written by Biliyar N. Bhat and published by . This book was released on 2018 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: "The present volume is focused on documenting the novel processing, fabrication, characterization, and testing approaches that are unique to aerospace materials/structures/systems"--Preface.
Download or read book Atlas of Stress corrosion and Corrosion Fatigue Curves written by A. J. McEvily and published by ASM International(OH). This book was released on 1990 with total page 568 pages. Available in PDF, EPUB and Kindle. Book excerpt: A reference for materials scientists that can be used to find the effects of various corrosive media and processing variables on the stress-corrosion cracking and corrosion fatigue characteristics of ferrous and nonferrous alloys. There are more than 500 stress/cracking-time curves, S/N curves, and
Download or read book Degradation of Implant Materials written by Noam Eliaz and published by Springer Science & Business Media. This book was released on 2012-08-21 with total page 521 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book reviews the current understanding of the mechanical, chemical and biological processes that are responsible for the degradation of a variety of implant materials. All 18 chapters will be written by internationally renowned experts to address both fundamental and practical aspects of research into the field. Different failure mechanisms such as corrosion, fatigue, and wear will be reviewed, together with experimental techniques for monitoring them, either in vitro or in vivo. Procedures for implant retrieval and analysis will be presented. A variety of biomaterials (stainless steels, titanium and its alloys, nitinol, magnesium alloys, polyethylene, biodegradable polymers, silicone gel, hydrogels, calcium phosphates) and medical devices (orthopedic and dental implants, stents, heart valves, breast implants) will be analyzed in detail. The book will serve as a broad reference source for graduate students and researchers studying biomedicine, corrosion, surface science, and electrochemistry.
Download or read book Extractive Metallurgy of Niobium written by A.K. Suri and published by Routledge. This book was released on 2017-11-13 with total page 272 pages. Available in PDF, EPUB and Kindle. Book excerpt: The growth and development witnessed today in modern science, engineering, and technology owes a heavy debt to the rare, refractory, and reactive metals group, of which niobium is a member. Extractive Metallurgy of Niobium presents a vivid account of the metal through its comprehensive discussions of properties and applications, resources and resource processing, chemical processing and compound preparation, metal extraction, and refining and consolidation. Typical flow sheets adopted in some leading niobium-producing countries for the beneficiation of various niobium sources are presented, and various chemical processes for producing pure forms of niobium intermediates such as chloride, fluoride, and oxide are discussed. The book also explains how to liberate the metal from its intermediates and describes the physico-chemical principles involved. It is an excellent reference for chemical metallurgists, hydrometallurgists, extraction and process metallurgists, and minerals processors. It is also valuable to a wide variety of scientists, engineers, technologists, and students interested in the topic.
Download or read book High Entropy Alloys written by Michael C. Gao and published by Springer. This book was released on 2016-04-27 with total page 516 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book provides a systematic and comprehensive description of high-entropy alloys (HEAs). The authors summarize key properties of HEAs from the perspective of both fundamental understanding and applications, which are supported by in-depth analyses. The book also contains computational modeling in tackling HEAs, which help elucidate the formation mechanisms and properties of HEAs from various length and time scales.
