Download or read book Duplex Stainless Steels written by R Gunn and published by Woodhead Publishing. This book was released on 1997-10-21 with total page 220 pages. Available in PDF, EPUB and Kindle. Book excerpt: Two very successful conferences - in Glasgow and Beaune - were held on duplex stainless steels during the first half of the '90s. This book takes keynote papers from each, and develops and expands them to bring the topics right up to date. There is new material to cover grades, specifications and standards, and the book is fully cross-references and indexed. The first reference book to be published on the increasingly popular duplex stainless steels, it will be widely welcomed by metallurgists, design and materials engineers, oil and gas engineers and anyone involved in materials development and properties. The first reference book on this relatively new engineering material Based on keynote papers from major international contributors Covers grades, standards and specifications
Download or read book Steels Processing Structure and Performance Second Edition written by George Krauss and published by ASM International. This book was released on 2015-03-01 with total page 705 pages. Available in PDF, EPUB and Kindle. Book excerpt: George Krauss, University Emeritus Professor, Colorado School of Mines and author of the best-selling ASM book Steels: Processing, Structure, and Performance, discusses some of the important additions and updates to the new second edition.
Download or read book Stainless Steels and Alloys written by Zoia Duriagina and published by BoD – Books on Demand. This book was released on 2019-02-13 with total page 160 pages. Available in PDF, EPUB and Kindle. Book excerpt: Materials science is the magic that allows us to change the chemical composition and microstructure of material to regulate its corrosion-mechanical, technological, and functional properties. Five major classes of stainless steels are widely used: ferritic, austenitic, martensitic, duplex, and precipitation hardening. Austenitic stainless steels are extensively used for service down to as low as the temperature of liquid helium (-269oC). This is largely due to the lack of a clearly defined transition from ductile to brittle fracture in impact toughness testing. Steels with ferritic or martensitic structures show a sudden change from ductile (safe) to brittle (unsafe) fracture over a small temperature difference. Even the best of these steels shows this behavior at temperatures higher than -100oC and in many cases only just below zero. Various types of stainless steel are used across the whole temperature range from ambient to 1100oC. This book will be useful to scientists, engineers, masters, graduate students, and students. I hope readers will enjoy this book and that it will serve to create new materials with unique properties.
Download or read book Duplex Stainless Steels written by Iris Alvarez-Armas and published by John Wiley & Sons. This book was released on 2013-01-16 with total page 338 pages. Available in PDF, EPUB and Kindle. Book excerpt: Duplex Stainless Steels (DSSs) are chromium-nickel-molybdenum-iron alloys that are usually in proportions optimized for equalizing the volume fractions of austenite and ferrite. Due to their ferritic-austenitic microstructure, they possess a higher mechanical strength and a better corrosion resistance than standard austenitic steels. This type of steel is now increasing its application and market field due to its very good properties and relatively low cost. This book is a review of the most recent progress achieved in the last 10 years on microstructure, corrosion resistance and mechanical strength properties, as well as applications, due to the development of new grades. Special attention will be given to fatigue and fracture behavior and to proposed models to account for mechanical behavior. Each subject will be developed in chapters written by experts recognized around the international industrial and scientific communities. The use of duplex stainless steels has grown rapidly in the last 10 years, particularly in the oil and gas industry, chemical tankers, pulp and paper as well as the chemical industry. In all these examples, topics like welding, corrosion resistance and mechanical strength properties (mainly in the fatigue domain) are crucial. Therefore, the update of welding and corrosion properties and the introduction of topics like texture effects, fatigue and fracture strength properties, and mechanical behavior modeling give this book specific focus and character.
Download or read book Stainless Steel Castings written by V. G. Behal and published by ASTM International. This book was released on 1982 with total page 466 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book HSLA Steels 2015 Microalloying 2015 Offshore Engineering Steels 2015 written by The Chinese Society for Metals and published by Springer. This book was released on 2017-03-22 with total page 1147 pages. Available in PDF, EPUB and Kindle. Book excerpt: This is a collection of papers presented at the joint conference of the 7th International Conference on High Strength Low Alloy Steels (HSLA Steels 2015), the International Conference on Microalloying 2015 (Microalloying 2015), and the International Conference on Offshore Engineering Steels 2015 (OES 2015). The papers focus on the exchange of the latest scientific and technological progresses on HSLA steels, microalloying steels, and offshore engineering steels over the past decades. The contributions are intended to strengthen cooperation between universities and research institutes, and iron and steel companies and users, and promote the further development in the fields all over the world.
Download or read book Practical Guidelines for the Fabrication of Duplex Stainless Steels written by International Molybdenum Association and published by . This book was released on 2009 with total page 63 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Comprehensive Structural Integrity written by Ian Milne and published by Elsevier. This book was released on 2003-07-25 with total page 4647 pages. Available in PDF, EPUB and Kindle. Book excerpt: The aim of this major reference work is to provide a first point of entry to the literature for the researchers in any field relating to structural integrity in the form of a definitive research/reference tool which links the various sub-disciplines that comprise the whole of structural integrity. Special emphasis will be given to the interaction between mechanics and materials and structural integrity applications. Because of the interdisciplinary and applied nature of the work, it will be of interest to mechanical engineers and materials scientists from both academic and industrial backgrounds including bioengineering, interface engineering and nanotechnology. The scope of this work encompasses, but is not restricted to: fracture mechanics, fatigue, creep, materials, dynamics, environmental degradation, numerical methods, failure mechanisms and damage mechanics, interfacial fracture and nano-technology, structural analysis, surface behaviour and heart valves. The structures under consideration include: pressure vessels and piping, off-shore structures, gas installations and pipelines, chemical plants, aircraft, railways, bridges, plates and shells, electronic circuits, interfaces, nanotechnology, artificial organs, biomaterial prostheses, cast structures, mining... and more. Case studies will form an integral part of the work.
Download or read book Scientific and Technical Aerospace Reports written by and published by . This book was released on 1978 with total page 1018 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Stainless Steels for Design Engineers written by Michael F. McGuire and published by ASM International. This book was released on 2008 with total page 311 pages. Available in PDF, EPUB and Kindle. Book excerpt: The rate of growth of stainless steel has outpaced that of other metals and alloys, and by 2010 may surpass aluminum as the second most widely used metal after carbon steel. The 2007 world production of stainless steel was approximately 30,000,000 tons and has nearly doubled in the last ten years. This growth is occurring at the same time that the production of stainless steel continues to become more consolidated. One result of this is a more widespread need to understand stainless steel with fewer resources to provide that information. The concurrent technical evolution in stainless steel and increasing volatility of raw material prices has made it more important for the engineers and designers who use stainless steel to make sound technical judgments about which stainless steels to use and how to use them.
Download or read book Nuclear Science Abstracts written by and published by . This book was released on 1976 with total page 1118 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Cracking Phenomena in Welds IV written by Thomas Böllinghaus and published by Springer. This book was released on 2016-02-10 with total page 502 pages. Available in PDF, EPUB and Kindle. Book excerpt: This is the fourth volume in the well-established series of compendiums devoted to the subject of weld hot cracking. It contains the papers presented at the 4th International Cracking Workshop held in Berlin in April 2014. In the context of this workshop, the term “cracking” refers to hot cracking in the classical and previous sense, but also to cold cracking, stress-corrosion cracking and elevated temp. solid-state cracking. A variety of different cracking subjects are discussed, including test standards, crack prediction, weldability determination, crack mitigation, stress states, numerical modelling, and cracking mechanisms. Likewise, many different alloys were investigated such as aluminum alloys, copper-aluminum dissimilar metal, austenitic stainless steel, nickel base alloys, duplex stainless steel, creep resistant steel, and high strength steel.
Download or read book Post Processing Techniques for Metal Based Additive Manufacturing written by Hao Wang and published by CRC Press. This book was released on 2023-09-04 with total page 311 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book shares insights on post-processing techniques adopted to achieve precision-grade surfaces of additive manufactured metals including material characterization techniques and the identified material properties. Post-processes are discussed from support structure removal and heat treatment to the material removal processes including hybrid manufacturing. Also discussed are case studies on unique applications of additive manufactured metals as an exemplary of the considerations taken during post-processing design and selection. Addresses the critical aspect of post-processing for metal additive manufacturing Provides systematic introduction of pertinent materials Demonstrates post-process technique selection with the enhanced understanding of material characterization methods and evaluation Includes in-depth validation of ultra-precision machining technology Reviews precision fabrication of industrial-grade titanium alloys, steels, and aluminium alloys, with additive manufacturing technology The book is aimed at researchers, professionals, and graduate students in advanced manufacturing, additive manufacturing, machining, and materials processing.
Download or read book Mechanics of Random and Multiscale Microstructures written by Dominique Jeulin and published by Springer. This book was released on 2014-05-04 with total page 270 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book reviews recent theoretical, computational and experimental developments in mechanics of random and multiscale solid materials. The aim is to provide tools for better understanding and prediction of the effects of stochastic (non-periodic) microstructures on materials’ mesoscopic and macroscopic properties. Particular topics involve a review of experimental techniques for the microstructure description, a survey of key methods of probability theory applied to the description and representation of microstructures by random modes, static and dynamic elasticity and non-linear problems in random media via variational principles, stochastic wave propagation, Monte Carlo simulation of random continuous and discrete media, fracture statistics models, and computational micromechanics.
Download or read book Trends in Welding Research 2012 Proceedings of the 9th International Conference written by Tarasankar DebRoy, Stan A. David, John N. DuPont, Toshihiko Koseki, Harry K. Bhadeshia and published by ASM International. This book was released on 2013-03-01 with total page 1117 pages. Available in PDF, EPUB and Kindle. Book excerpt: The Trends conference attracts the world's leading welding researchers. Topics covered in this volume include friction stir welding, sensing, control and automation, microstructure and properties, welding processes, procedures and consumables, weldability, modeling, phase transformations, residual stress and distortion, physical processes in welding, and properties and structural integrity of weldments.
Download or read book Physical Aspects of Fracture written by Elisabeth Bouchaud and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 369 pages. Available in PDF, EPUB and Kindle. Book excerpt: The main scope of this Cargese NATO Advanced Study Institute (June 5-17 2000) was to bring together a number of international experts, covering a large spectrum of the various Physical Aspects of Fracture. As a matter of fact, lecturers as well as participants were coming from various scientific communities: mechanics, physics, materials science, with the common objective of progressing towards a multi-scale description of fracture. This volume includes papers on most materials of practical interest: from concrete to ceramics through metallic alloys, glasses, polymers and composite materials. The classical fields of damage and fracture mechanisms are addressed (critical and sub-critical quasi-static crack propagation, stress corrosion, fatigue, fatigue-corrosion . . . . as well as dynamic fracture). Brittle and ductile fractures are considered and a balance has been carefully kept between experiments, simulations and theoretical models, and between the contributions of the various communities. New topics in damage and fracture mechanics - the effect of disorder and statistical aspects, dynamic fracture, friction and fracture of interfaces - were also explored. This large overview on the Physical Aspects of Fracture shows that the old barriers built between the different scales will soon "fracture". It is no more unrealistic to imagine that a crack initiated through a molecular dynamics description could be propagated at the grain level thanks to dislocation dynamics included in a crystal plasticity model, itself implemented in a finite element code. Linking what happens at the atomic scale to fracture of structures as large as a dam is the new emerging challenge.
Download or read book PROBAMAT 21st Century Probabilities and Materials written by G.N. Frantziskonis and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 615 pages. Available in PDF, EPUB and Kindle. Book excerpt: There are numerous technological materials - such as metals, polymers, ceramics, concrete, and many others - that vary in properties and serviceability. However, the almost universal common theme to most real materials is that their properties depend on the scale at which the analysis or observation takes place and at each scale "probabilities" play an important role. Here the word "probabilities" is used in a wider than the classical sense. In order to increase the efficiency and serviceability of these materials, researchers from NATO, CP and other countries were brought together to exchange knowledge and develop avenues for progress and applications in the st 21 century. The workshop began by reviewing progress in the subject area over the past few years and by identifying key questions that remain open. One point was how to observe/measure material properties at different scales and whether a probabilistic approach, at each scale, was always applicable and advantageous. The wide range of materials, from wood to advanced metals and from concrete to complex advanced composites, and the diversity of applications, e.g. fatigue, fracture, deformation, etc., were recognized as "obstacles" in identifying a "universal" approach.
