Download or read book Experimental Performance of a Micromachined Heat Flux Sensor written by S. Stefanescu and published by . This book was released on 1998 with total page 18 pages. Available in PDF, EPUB and Kindle. Book excerpt: Steady-state and frequency response calibration of a microfabricated heat-flux sensor have been completed. This sensor is batch fabricated using standard, micromachining techniques, allowing both miniaturization and the ability to create arrays of sensors and their corresponding interconnects. Both high-frequency and spatial response is desired, so the sensors are both thin and of small cross-sectional area. Thin-film, temperature-sensitive resistors are used as the active gauge elements. Two sensor configurations are investigated: (1) a Wheatstone-bridge using four resistors; and (2) a simple, two-resistor design. In each design, one resistor (or pair) is covered by a thin layer (5000 A) thermal barrier; the other resistor (or pair) is covered by a thick (5 microns) thermal barrier. The active area of a single resistor is 360 microns by 360 microns; the total gauge area is 1.5 mm square. The resistors are made of 2000 A-thick metal; and the entire gauge is fabricated on a 25 microns-thick flexible, polyimide substrate. Heat flux through the surface changes the temperature of the resistors and produces a corresponding change in resistance. Sensors were calibrated using two radiation heat sources: (1) a furnace for steady-state, and (2) a light and chopper for frequency response.
Download or read book 33rd AIAA ASME SAE ASEE Joint Propulsion Conference Exhibit written by and published by . This book was released on 1997 with total page 598 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book ARO and AFOSR Contractors Meeting in Chemical Propulsion Held in Virginia Beach Virginia on 3 6 June 1996 written by David M. Mann and published by . This book was released on 1996 with total page 302 pages. Available in PDF, EPUB and Kindle. Book excerpt: Partial contents: Supercritical droplet behavior; Fundamentals of acoustic instabilities in liquid-propellant rockets; Modeling liquid jet atomization proceses; Liquid-propellant droplets dynamics and combustions in supercritical forced convective environments; Contributions of shear coaxial injectors to liquid rocket motor combustion instabilities; High pressure combustion studies under combustion driven oscillatory flow conditions; Droplet collision on liquid propellant combustion; Combustion and plumes; Development of a collisional radiative emission model for strongly nonequilibrium flows; Energy transfer processes in the production of excited states in reacting rocket flows; modeling nonequilibrium radiation in high altitude plumes; kinetics of plume radiation, and of HEDMs and metallic fuels combustion; Nonsteady combustion mechanisms of advanced solid propellants; Chemical mechanisms at the burning surface. p15
Download or read book Mems for Automotive and Aerospace Applications written by Michael Kraft and published by Elsevier. This book was released on 2013-01-02 with total page 358 pages. Available in PDF, EPUB and Kindle. Book excerpt: MEMS for automotive and aerospace applications reviews the use of Micro-Electro-Mechanical-Systems (MEMS) in developing solutions to the unique challenges presented by the automotive and aerospace industries.Part one explores MEMS for a variety of automotive applications. The role of MEMS in passenger safety and comfort, sensors for automotive vehicle stability control applications and automotive tire pressure monitoring systems are considered, along with pressure and flow sensors for engine management, and RF MEMS for automotive radar sensors. Part two then goes on to explore MEMS for aerospace applications, including devices for active drag reduction in aerospace applications, inertial navigation and structural health monitoring systems, and thrusters for nano- and pico-satellites. A selection of case studies are used to explore MEMS for harsh environment sensors in aerospace applications, before the book concludes by considering the use of MEMS in space exploration and exploitation.With its distinguished editors and international team of expert contributors, MEMS for automotive and aerospace applications is a key tool for MEMS manufacturers and all scientists, engineers and academics working on MEMS and intelligent systems for transportation. - Chapters consider the role of MEMS in a number of automotive applications, including passenger safety and comfort, vehicle stability and control - MEMS for aerospace applications are also discussed, including active drag reduction, inertial navigation and structural health monitoring systems - Presents a number of case studies exploring MEMS for harsh environment sensors in aerospace
Download or read book International Aerospace Abstracts written by and published by . This book was released on 1999 with total page 974 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Handbook of Thermal Science and Engineering written by and published by Springer. This book was released on 2018-07-31 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This Handbook provides researchers, faculty, design engineers in industrial R&D, and practicing engineers in the field concise treatments of advanced and more-recently established topics in thermal science and engineering, with an important emphasis on micro- and nanosystems, not covered in earlier references on applied thermal science, heat transfer or relevant aspects of mechanical/chemical engineering. Major sections address new developments in heat transfer, transport phenomena, single- and multiphase flows with energy transfer, thermal-bioengineering, thermal radiation, combined mode heat transfer, coupled heat and mass transfer, and energy systems. Energy transport at the macro-scale and micro/nano-scales is also included. The internationally recognized team of authors adopt a consistent and systematic approach and writing style, including ample cross reference among topics, offering readers a user-friendly knowledgebase greater than the sum of its parts, perfect for frequent consultation. The Handbook of Thermal Science and Engineering is ideal for academic and professional readers in the traditional and emerging areas of mechanical engineering, chemical engineering, aerospace engineering, bioengineering, electronics fabrication, energy, and manufacturing concerned with the influence thermal phenomena.
Download or read book Application of Microfabrication to Fluid Mechanics 1994 written by Promode R. Bandyopadhyay and published by . This book was released on 1994 with total page 104 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book AIAA Journal written by American Institute of Aeronautics and Astronautics and published by . This book was released on 2002 with total page 1358 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book The MEMS Handbook written by Mohamed Gad-el-Hak and published by CRC Press. This book was released on 2001-09-27 with total page 1386 pages. Available in PDF, EPUB and Kindle. Book excerpt: The revolution is well underway. Our understanding and utilization of microelectromechanical systems (MEMS) are growing at an explosive rate with a worldwide market approaching billions of dollars. In time, microdevices will fill the niches of our lives as pervasively as electronics do right now. But if these miniature devices are to fulfill their mammoth potential, today's engineers need a thorough grounding in the underlying physics, modeling techniques, fabrication methods, and materials of MEMS. The MEMS Handbook delivers all of this and more. Its team of authors-unsurpassed in their experience and standing in the scientific community- explore various aspects of MEMS: their design, fabrication, and applications as well as the physical modeling of their operations. Designed for maximum readability without compromising rigor, it provides a current and essential overview of this fledgling discipline.
Download or read book Handbook of Chemical and Biological Sensors written by R.F Taylor and published by CRC Press. This book was released on 1996-01-01 with total page 1248 pages. Available in PDF, EPUB and Kindle. Book excerpt: The Handbook of Chemical and Biological Sensors focuses on the development of sensors to recognize substances rather than physical quantities. This fully inclusive book examines devices that use a biological sensing element to detect and measure chemical and biological species as well as those that use a synthetic element to achieve a similar result. A first port of call for anyone with a specific interest, question, or problem relating to this area, this comprehensive source of reference serves as a guide for practicing scientists and as a text for many graduate courses. It presents relevant physics to chemists, chemistry to materials scientists, materials science to electronic engineers, and fabrication technology to all of the above. In addition, the handbook is useful both to newcomers and to experienced researchers who wish to broaden their knowledge of the constituent disciplines of this wide-ranging field.
Download or read book Proceedings of the ASME Heat Transfer Division 2005 written by and published by . This book was released on 2005 with total page 1070 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Selected Papers from the ISTEGIM 19 written by Lucien Baldas and published by MDPI. This book was released on 2021-03-01 with total page 180 pages. Available in PDF, EPUB and Kindle. Book excerpt: This Special Issue compiles 11 scientific works that were presented during the International Symposium on Thermal Effects in Gas Flow in Microscale, ISTEGIM 2019, held in Ettlingen, Germany, in October 2019. This symposium was organized in the framework of the MIGRATE Network, an H2020 Marie Skłodowska-Curie European Training Network that ran from November 2015 to October 2019 (www.migrate2015.eu). MIGRATE intends to address some of the current challenges in innovation that face the European industry with regard to heat and mass transfer in gas-based microscale processes. The papers collected in this book focus on fundamental issues that are encountered in microfluidic systems involving gases, such as the analysis of gas–surface interactions under rarefied conditions, the development of innovative integrated microsensors for airborne pollutants, new experimental techniques for the measurement of local quantities in miniaturized devices and heat transfer issues inside microchannels. The variety of topics addressed in this book emphasizes that multi-disciplinarity is the real common thread of the current applied research in microfluidics. We hope that this book will help to stimulate early-stage researchers who are working in microfluidics all around the world. This book is dedicated to them!
Download or read book MEMS Materials and Processes Handbook written by Reza Ghodssi and published by Springer Science & Business Media. This book was released on 2011-03-18 with total page 1211 pages. Available in PDF, EPUB and Kindle. Book excerpt: MEMs Materials and Processes Handbook" is a comprehensive reference for researchers searching for new materials, properties of known materials, or specific processes available for MEMS fabrication. The content is separated into distinct sections on "Materials" and "Processes". The extensive Material Selection Guide" and a "Material Database" guides the reader through the selection of appropriate materials for the required task at hand. The "Processes" section of the book is organized as a catalog of various microfabrication processes, each with a brief introduction to the technology, as well as examples of common uses in MEMs.
Download or read book IEEE Sensors Journal written by and published by . This book was released on 2003 with total page 544 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Microelectromechanical Systems written by and published by . This book was released on 1999 with total page 630 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book MEMS written by Mohamed Gad-el-Hak and published by CRC Press. This book was released on 2005-11-29 with total page 576 pages. Available in PDF, EPUB and Kindle. Book excerpt: As our knowledge of microelectromechanical systems (MEMS) continues to grow, so does The MEMS Handbook. The field has changed so much that this Second Edition is now available in three volumes. Individually, each volume provides focused, authoritative treatment of specific areas of interest. Together, they comprise the most comprehensive collection
Download or read book Encyclopedia of Microfluidics and Nanofluidics written by Dongqing Li and published by Springer Science & Business Media. This book was released on 2008-08-06 with total page 2242 pages. Available in PDF, EPUB and Kindle. Book excerpt: Covering all aspects of transport phenomena on the nano- and micro-scale, this encyclopedia features over 750 entries in three alphabetically-arranged volumes including the most up-to-date research, insights, and applied techniques across all areas. Coverage includes electrical double-layers, optofluidics, DNC lab-on-a-chip, nanosensors, and more.
