Download or read book Temporary Cementitious Sealers in Enhanced Geothermal Systems written by and published by . This book was released on 2011 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: Unlike conventional hydrothennal geothermal technology that utilizes hot water as the energy conversion resources tapped from natural hydrothermal reservoir located at H"0 km below the ground surface, Enhanced Geothermal System (EGS) must create a hydrothermal reservoir in a hot rock stratum at temperatures e"00 C, present in H" km deep underground by employing hydraulic fracturing. This is the process of initiating and propagating a fracture as well as opening pre-existing fractures in a rock layer. In this operation, a considerable attention is paid to the pre-existing fractures and pressure-generated ones made in the underground foundation during drilling and logging. These fractures in terms of lost circulation zones often cause the wastage of a substantial amount of the circulated water-based drilling fluid or mud. Thus, such lost circulation zones must be plugged by sealing materials, so that the drilling operation can resume and continue. Next, one important consideration is the fact that the sealers must be disintegrated by highly pressured water to reopen the plugged fractures and to promote the propagation of reopened fractures. In response to this need, the objective of this phase I project in FYs 2009-2011 was to develop temporary cementitious fracture sealing materials possessing self-degradable properties generating when e"200 C-heated scalers came in contact with water. At BNL, we formulated two types of non-Portland cementitious systems using inexpensive industrial by-products with pozzolanic properties, such as granulated blast-furnace slag from the steel industries, and fly ashes from coal-combustion power plants. These byproducts were activated by sodium silicate to initiate their pozzolanic reactions, and to create a cemetitious structure. One developed system was sodium silicate alkali-activated slag/Class C fly ash (AASC); the other was sodium silicate alkali-activated slag/Class F fly ash (AASF) as the binder of temper-try sealers. Two specific additives without sodium silicate as alkaline additive were developed in this project: One additive was the sodium carboxymethyl cellulose (CMC) as self-degradation promoting additive; the other was the hard-burned magnesium oxide (MgO) made from calcinating at 1,000-1,500 C as an expansive additive. The AASC and AASF cementitious sealers made by incorporating an appropriate amount of these additives met the following six criteria: 1) One dry mix component product; 2) plastic viscosity, 20 to 70 cp at 300 rpm; 3) maintenance of pumpability for at least 1 hour at 85 C; 4) compressive strength>2000 psi; 5) self-degradable by injection with water at a certain pressure; and 6) expandable and swelling properties; e".5% of total volume of the sealer.

Download or read book Materials Challenges in Alternative and Renewable Energy II written by George Wicks and published by John Wiley & Sons. This book was released on 2013-01-03 with total page 354 pages. Available in PDF, EPUB and Kindle. Book excerpt: The overall efficiency, effectiveness, and practicality of potential future energy sources and systems are directly related to many materials-related factors. This volume features 30 papers presented during the 2012 Materials Challenges in Alternative and Renewable Energy Conference. They cover the latest developments involving materials for alternative and renewable energy sources and systems, including batteries and energy storage, hydrogen, solar, wind, geothermal, biomass, and nuclear, as well as materials availability, the energy grid, and nanocomposites.

Download or read book Self decomposable Fibrous Bridging Additives for Temporary Cementitious Fracture Sealers in EGS Wells written by and published by . This book was released on 2012 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: This study evaluates compatibility of a self-degradable temporary fracture sealer with the drilling mud and plugging and self-degrading performance of different fibers to be used in combination with the sealer. The sodium silicate-activated slag/Class C fly ash (SSASC) cementitious sealer must plug fractures at 85oC to allow continuous well drilling and it must degrade and leave the fractures open for water at later times when exposed to temperatures above 200oC. The sealer showed good compatibility with the mud. Even the blend of 80/20 vol.% of sealer/mud reached a compressive strength of more than 2000 psi set as one of the material criteria, mostly due to the additional activation of the slag and Class C fly ash by the alkaline ingredient present in the drilling fluid. In contrast, the drilling fluid was detrimental to the compressive strength development in conventional Class G well cement, so that it failed to meet this criterion. Among several organic fibers tested both polyvinyl alcohol (PVA)-and nylon-based fibers showed adequate plugging of the sealer in slot nozzles of 1-in. wide x 6-in. long x 0.08 in. and 0.24 in. high under pressures up to 700 psi. PVA fibers displayed better compressive toughness and self-degrading properties than nylon. The compressive toughness of sealers made by adding 1.0 wt% 6 mm-length PVA and 0.5 wt% 19 mm-length PVA was 9.5-fold higher than that of a non-bridged sealer. One factor governing the development of such high toughness was an excellent adherence of PVA to the SSASC cement. The alkali-catalyzed self-decomposition of PVA at 200°C led to the morphological transformation of the material from a fibrous structure to a microscale flake-like structure that helped the desirable conversion of the sealer into small fragments. In contrast, nylon's decomposition provided a reticular network structure in the self-degraded sealer resulting in bigger fragments compared against the sealer with PVA. The PVA fiber has a high potential as a self-decomposable bridging additive in the SSASC cement sealer.

Download or read book Self degradable Cementitious Sealing Materials written by and published by . This book was released on 2010 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: A self-degradable alkali-activated cementitious material consisting of a sodium silicate activator, slag, Class C fly ash, and sodium carboxymethyl cellulose (CMC) additive was formulated as one dry mix component, and we evaluated its potential in laboratory for use as a temporary sealing material for Enhanced Geothermal System (EGS) wells. The self-degradation of alkali-activated cementitious material (AACM) occurred, when AACM heated at temperatures of ≥200 C came in contact with water. We interpreted the mechanism of this water-initiated self-degradation as resulting from the in-situ exothermic reactions between the reactants yielded from the dissolution of the non-reacted or partially reacted sodium silicate activator and the thermal degradation of the CMC. The magnitude of self-degradation depended on the CMC content; its effective content in promoting degradation was ≥0.7%. In contrast, no self-degradation was observed from CMC-modified Class G well cement. For 200 C-autoclaved AACMs without CMC, followed by heating at temperatures up to 300 C, they had a compressive strength ranging from 5982 to 4945 psi, which is ≈3.5-fold higher than that of the commercial Class G well cement; the initial- and final-setting times of this AACM slurry at 85 C were ≈60 and ≈90 min. Two well-formed crystalline hydration phases, 1.1 nm tobermorite and calcium silicate hydrate (I), were responsible for developing this excellent high compressive strength. Although CMC is an attractive, as a degradation-promoting additive, its addition to both the AACM and the Class G well cement altered some properties of original cementitious materials; among those were an extending their setting times, an increasing their porosity, and lowering their compressive strength. Nevertheless, a 0.7% CMC-modified AACM as self-degradable cementitious material displayed the following properties before its breakdown by water; ≈120 min initial- and ≈180 min final-setting times at 85 C, and 1825 to 1375 psi compressive strength with 51.2 to 55.0% porosity up to 300 C.

Download or read book Temporary Bridging Agents for Use in Drilling and Completion of Enhanced Geothermal Systems written by and published by . This book was released on 2011 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: CSI Technologies, in conjunction with Alta Rock Energy and the University of Utah have undergone a study investigating materials and mechanisms with potential for use in Enhanced Geothermal Systems wells as temporary diverters or lost circulation materials. Studies were also conducted with regards to particle size distribution and sealing effectiveness using a lab-scale slot testing apparatus to simulate fractures. From the slot testing a numerical correlation was developed to determine the optimal PSD for a given fracture size. Field trials conducted using materials from this study were also successful.

Download or read book Materials Challenges in Alternative and Renewable Energy written by George Wicks and published by John Wiley & Sons. This book was released on 2012-01-10 with total page 430 pages. Available in PDF, EPUB and Kindle. Book excerpt: This useful, one-stop resource for understanding the most important issues in materials challenges in alternative and renewable energy. The logically organized and carefully selected articles give insight into materials challenges in alternative renewable energy and incorporate the latest developments related to materials challenges in alternative renewable energy, including hydrogen, batteries and energy storage materials, hydropower, and biomass.

Download or read book Self degradable Slag Class F Fly Ash Blend Cements written by and published by . This book was released on 2011 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: Self-degradable slag/Class F fly ash blend pozzolana cements were formulated, assuming that they might serve well as alternative temporary fracture sealers in Enhanced Geothermal System (EGS) wells operating at temperatures of ≥ 200 C. Two candidate formulas were screened based upon material criteria including an initial setting time ≥ 60 min at 85 C, compressive strength ≥ 2000 psi for a 200 C autoclaved specimen, and the extent of self-degradation of cement heated at ≥ 200 C for it was contacted with water. The first screened dry mix formula consisted of 76.5 wt% slag-19.0 wt% Class F fly ash-3.8 wt% sodium silicate as alkali activator, and 0.7 wt% carboxymethyl cellulose (CMC) as the self-degradation promoting additive, and second formula comprised of 57.3 wt% slag, 38.2 wt% Class F fly ash, 3.8 wt% sodium silicate, and 0.7 wt% CMC. After mixing with water and autoclaving it at 200 C, the aluminum-substituted 1.1 nm tobermorite crystal phase was identified as hydrothermal reaction product responsible for the development of a compressive strength of 5983 psi. The 200 C-autoclaved cement made with the latter formula had the combined phases of tobermorite as its major reaction product and amorphous geopolymer as its minor one providing a compressive strength of 5271 psi. Sodium hydroxide derived from the hydrolysis of sodium silicate activator not only initiated the pozzolanic reaction of slag and fly ash, but also played an important role in generating in-situ exothermic heat that significantly contributed to promoting self-degradation of cementitious sealers. The source of this exothermic heat was the interactions between sodium hydroxide, and gaseous CO2 and CH3COOH by-products generated from thermal decomposition of CMC at ≥ 200 C in an aqueous medium. Thus, the magnitude of this self-degradation depended on the exothermic temperature evolved in the sealer; a higher temperature led to a sever disintegration of sealer. The exothermic temperature was controlled by the extent of thermal decomposition of CMC, demonstrating that CMC decomposed at higher temperature emitted more gaseous reactants. Hence, such large emission enhanced the evolution of in-situ exothermic heat. In contrast, the excessive formation of geopolymer phase due to more incorporation of Class F fly ash into this cementitious system affected its ability to self-degrade, reflecting that there was no self-degradation. The geopolymer was formed by hydrothermal reactions between sodium hydroxide from sodium silicate and mullite in Class F fly ash. Thus, the major reason why geopolymer-based cementitiuos sealers did not degrade after heated sealers came in contact with water was their lack of free sodium hydroxide.

Download or read book Geothermal Direct Use Engineering and Design Guidebook written by Paul J. Lienau and published by . This book was released on 1989 with total page 430 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Geothermal Energy written by Mary H. Dickson and published by Routledge. This book was released on 2013-07-04 with total page 430 pages. Available in PDF, EPUB and Kindle. Book excerpt: Geothermal energy refers to the heat contained within the Earth that generates geological phenomena on a planetary scale. Today, this term is often associated with man's efforts to tap into this vast energy source. Geothermal Energy: utilization and technology is a detailed reference text, describing the various methods and technologies used to exploit the earth's heat. Beginning with an overview of geothermal energy and the state of the art, leading international experts in the field cover the main applications of geothermal energy, including: electricity generation space and district heating space cooling greenhouse heating aquaculture industrial applications The final third of the book focuses upon environmental impact and economic, financial and legal considerations, providing a comprehensive review of these topics. Each chapter is written by a different author, but to a set style, beginning with aims and objectives and ending with references, self-assessment questions and answers. Case studies are included throughout. Whilst written primarily for professionals and students interested in learning more about geothermal energy, the book also offers those new to the field and the general geothermal community an opportunity to understand and review the potential of this exciting alternative energy source. Published with UNESCO

Download or read book International Collaboration for Geothermal Energy in the Americas written by Geothermal Resources Council. Annual Meeting and published by . This book was released on 2003 with total page 1028 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Scientific and Technical Aerospace Reports written by and published by . This book was released on with total page 1026 pages. Available in PDF, EPUB and Kindle. Book excerpt: Lists citations with abstracts for aerospace related reports obtained from world wide sources and announces documents that have recently been entered into the NASA Scientific and Technical Information Database.

Download or read book Introduction to Permanent Plug and Abandonment of Wells written by Mahmoud Khalifeh and published by Springer Nature. This book was released on 2020-01-27 with total page 285 pages. Available in PDF, EPUB and Kindle. Book excerpt: This open access book offers a timely guide to challenges and current practices to permanently plug and abandon hydrocarbon wells. With a focus on offshore North Sea, it analyzes the process of plug and abandonment of hydrocarbon wells through the establishment of permanent well barriers. It provides the reader with extensive knowledge on the type of barriers, their functioning and verification. It then discusses plug and abandonment methodologies, analyzing different types of permanent plugging materials. Last, it describes some tests for verifying the integrity and functionality of installed permanent barriers. The book offers a comprehensive reference guide to well plugging and abandonment (P&A) and well integrity testing. The book also presents new technologies that have been proposed to be used in plugging and abandoning of wells, which might be game-changing technologies, but they are still in laboratory or testing level. Given its scope, it addresses students and researchers in both academia and industry. It also provides information for engineers who work in petroleum industry and should be familiarized with P&A of hydrocarbon wells to reduce the time of P&A by considering it during well planning and construction.

Download or read book Energy Research Abstracts written by and published by . This book was released on 1986 with total page 760 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Handbook of Polymer Modified Concrete and Mortars written by Yoshihiko Ohama and published by William Andrew. This book was released on 1995-12-31 with total page 247 pages. Available in PDF, EPUB and Kindle. Book excerpt: Mortar and concrete made with portland cement has been a popular construction material in the world for the past 170 years or more. However, cement mortar and concrete have some disadvantages such as delayed hardening, low tensile strength, large drying shrinkage and low chemical resistance. To reduce these disadvantages, polymers have been utilized as an additive.Polymer-modified or polymer cement mortar (PCM) and concrete (PCC) are the materials which are made by partially replacing the cement hydrate binders of conventional cement mortar or concrete, with polymers. This book deals with the principles of polymer modification for cement composites, the process technology, properties and applications of the polymer-modified mortar and concrete, and special polymer-modified systems such as M DF cement, antiwashout underwater concrete, polymer-ferrocement, and artificial I wood.The polymeric admixtures or cement modifiers include latexes or emulsions, redispersible polymer powders, water-soluble polymers, liquid resins and monomers.This book describes the current knowledge and information of polymer-modified mortars and concretes, and discusses or reviews the following items in detail:1. Principles of polymer modification for cement composites.2. Process technology of polymer-modified mortars and concretes.3. Properties of polymer-modified mortars and concretes.4. Applications of polymer-modified mortars and concretes.5. Special polymer-modified systems such as MDF cements, antiwashout underwater concretes, polymer-ferrocements, and artificial woods.

Download or read book Lost Circulation written by Alexandre Lavrov and published by Gulf Professional Publishing. This book was released on 2016-03-16 with total page 266 pages. Available in PDF, EPUB and Kindle. Book excerpt: Lost Circulation: Mechanisms and Solutions provides the latest information on a long-existing problem for drilling and cementing engineers that can cause improper drilling conditions, safety risks, and annual losses of millions of wasted dollars for oil and gas companies. While several conferences have convened on the topic, this book is the first reliable reference to provide a well-rounded, unbiased approach on the fundamental causes of lost circulation, how to diagnose it in the well, and how to treat and prevent it in future well planning operations. As today's drilling operations become more complex, and include situations such as sub-salt formations, deepwater wells with losses caused by cooling, and more depleted reservoirs with reduced in-situ stresses, this book provides critical content on the current state of the industry that includes a breakdown of basics on stresses and fractures and how drilling fluids work in the wellbore. The book then covers the more practical issues caused by induced fractures, such as how to understand where the losses are occurring and how to use proven preventative measures such as wellbore strengthening and the effect of base fluid on lost circulation performance. Supported by realistic case studies, this book separates the many myths from the known facts, equipping today's drilling and cementing engineer with a go-to solution for every day well challenges. - Understand the processes, challenges and solutions involved in lost circulation, a critical problem in drilling - Gain a balance between fundamental understanding and practical application through real-world case studies - Succeed in solving lost circulation in today's operations such as wells involving casing drilling, deepwater, and managed pressure drilling

Download or read book Alternative Energy Sources Geothermal energy and hydro power written by T. Nejat Veziroğlu and published by . This book was released on 1978 with total page 424 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Geothermal energy and hydro power written by T. Nejat Veziroğlu and published by . This book was released on 1978 with total page 424 pages. Available in PDF, EPUB and Kindle. Book excerpt: