Download or read book Synthesis of Silicon and Germanium Nanowires and Si Ge Nanowire Heterostructures written by Teresa J. Clement and published by . This book was released on 2007 with total page 272 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Silicon and Germanium Nanostructures written by Xiaotang Lu and published by . This book was released on 2015 with total page 404 pages. Available in PDF, EPUB and Kindle. Book excerpt: A variety of chemical routes exist for a wide range of nanomaterials with tunable size, shape, composition and surface chemistry. Of these materials, silicon (Si) and germanium (Ge) nanomaterials have been some of the most challenging to synthesize. Solution-liquid-solid (SLS) growth of Si was studied using tin (Sn) as the seeding metal. Si nanorods with narrow diameters can be grown by the decomposition of trisilane in hot squalane in the presence of Sn nanocrystals. Photoluminescence could be obtained from the Si nanorods by thermal hydrosilylation passivation. This colloidal synthesis could be further simplified to a single-step reaction procedure by the in situ formation of Sn seed particles. In addition to trisilane as a Si source, isotetrasilane, neopentasilane and cyclohexasilane were studied for Si nanorod growth: all three reactants enabled nanorod formation at lower growth temperatures. A monophenylsilane (MPS) enhanced growth was discovered for supercritical fluid-liquid-solid (SFLS) growth of Ge nanowires that enables the Ge conversion of ~100%. A variety of metalorganic compounds were studied for replacing pre-synthesized metal nanoparticles to induce Ge nanowire growth. Si and Ge nanowires are some of the most promising anode materials in lithium ion batteries (LIBs) because of their high lithium storage capacity. However, the significant chemical and physical changes that occur during cycling hamper their practical uses. In situ transmission electron microscopy (TEM) techniques were conducted to observe and understand structural and interfacial changes of the Si and Ge nanowires during electrochemical cycling; and, therefore, resolving the problems with current anodes by materials modification. The in situ TEM experiments showed that the incorporation of Sn into Si nanowires can enhance their rate capability. But the enhanced Li diffusion leads to the premature pore formation in Si nanowires. Ge nanowires has been discovered the potential as sodium ion battery anodes after an initial activation with a lithiation step to amorphize the nanowires.
Download or read book Synthesis Fabrication and Characterization of Ge Si Axial Nanowire Heterostructure Tunnel FETs written by and published by . This book was released on 2010 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: Axial Ge/Si heterostructure nanowires allow energy band-edge engineering along the axis of the nanowire, which is the charge transport direction, and the realization of asymmetric devices for novel device architectures. This work reports on two advances in the area of heterostructure nanowires and tunnel FETs: (i) the realization of 100% compositionally modulated Si/Ge axial heterostructure nanowires with lengths suitable for device fabrication and (ii) the design and implementation of Schottky barrier tunnel FETs on these nanowires for high-on currents and suppressed ambipolar behavior. Initial prototype devices resulted in a current drive in excess of 100 [mu]A/[mu]m (I/[pi]D) and 105 I{sub on}/I{sub off} ratios. These results demonstrate the potential of such asymmetric heterostructures (both in the semiconductor channel and metal-semiconductor barrier heights) for low-power and high performance electronics.
Download or read book Silicon Germanium SiGe Nanostructures written by Y. Shiraki and published by Elsevier. This book was released on 2011-02-26 with total page 649 pages. Available in PDF, EPUB and Kindle. Book excerpt: Nanostructured silicon-germanium (SiGe) opens up the prospects of novel and enhanced electronic device performance, especially for semiconductor devices. Silicon-germanium (SiGe) nanostructures reviews the materials science of nanostructures and their properties and applications in different electronic devices. The introductory part one covers the structural properties of SiGe nanostructures, with a further chapter discussing electronic band structures of SiGe alloys. Part two concentrates on the formation of SiGe nanostructures, with chapters on different methods of crystal growth such as molecular beam epitaxy and chemical vapour deposition. This part also includes chapters covering strain engineering and modelling. Part three covers the material properties of SiGe nanostructures, including chapters on such topics as strain-induced defects, transport properties and microcavities and quantum cascade laser structures. In Part four, devices utilising SiGe alloys are discussed. Chapters cover ultra large scale integrated applications, MOSFETs and the use of SiGe in different types of transistors and optical devices. With its distinguished editors and team of international contributors, Silicon-germanium (SiGe) nanostructures is a standard reference for researchers focusing on semiconductor devices and materials in industry and academia, particularly those interested in nanostructures. Reviews the materials science of nanostructures and their properties and applications in different electronic devices Assesses the structural properties of SiGe nanostructures, discussing electronic band structures of SiGe alloys Explores the formation of SiGe nanostructuresfeaturing different methods of crystal growth such as molecular beam epitaxy and chemical vapour deposition
Download or read book Semiconductor Nanowires written by Jie Xiang and published by Royal Society of Chemistry. This book was released on 2015 with total page 463 pages. Available in PDF, EPUB and Kindle. Book excerpt: A timely reference from leading experts on semiconductor nanowires and their applications.
Download or read book Study of Catalyzed Growth of Germanium Nanowires written by Shruti Vivek Thombare and published by . This book was released on 2013 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: Semiconductor nanowires are of great interest for application in nanoelectronics, nanophotonics, sensors and energy technologies. Particular attention has focused on Si and Ge nanowires because of their compatibility with Si integrated circuit technology. The great majority of literature studies of Ge nanowire growth have used Au as a catalyst for "bottom-up" synthesis of deposited wires. In most cases, growth occurs by the vapor-liquid-solid (VLS) mechanism. Gold has been a popular choice as a catalyst in part because it forms a eutectic liquid with Ge at temperatures below 400 °C, permitting generally high-quality and spatially-controlled crystal growth at very low temperatures. However, concerns exist about possible Au contamination of VLS-grown nanowire devices and, in particular, semiconductor processing facilities used to fabricate them. Gold is a fast diffuser in diamond cubic crystals and produces trap levels deep in the band gap of both Ge and Si, making it a significant cross-contamination hazard in semiconductor fabrication. Moreover, VLS is not well suited to synthesis of nanowires with abrupt grown-in p-n junctions or semiconductor heterostructures, which are interesting for many device applications. This has provided additional motivation to investigate the growth of semiconductor nanowires via the vapor-solid-solid (VSS) mechanism using alternative catalysts to Au. VSS nanowires can be grown at reduced temperatures compared to VLS, as the catalyst is not molten. Literature reports indicate that the morphology of Ge nanowires grown using alternative catalysts via VSS is not as easily controlled as that of VLS grown Ge nanowires with Au as a catalyst; mixtures of straight, twisted, and defective nanowires are reported for different catalysts and growth conditions. A size-dependent wire morphology transition from straight to tortuous nanowires in VSS growth of Ge nanowires using a Ni-based catalyst is discussed here. The catalyst phase was identified as orthorhombic NiGe, which is reported to be a state-of-the-art contact material in Si-compatible semiconductor devices. Using detailed transmission electron microscopy analysis of the nanowire and catalyst morphology and composition, the role of sidewall and catalyst/nanowire interface energetics as well as crystal defects in dictating the observed wire diameter effect on VSS growth morphology was analyzed. Development of optimized processes for bottom-up synthesis of these nanowires requires a more quantitative understanding of the VSS wire growth mechanism. Therefore, the kinetics of VSS nanowire growth, probing the rate-limiting step for various growth conditions was investigated. The effect of growth parameters such as growth temperature and precursor partial pressure on the nanowire growth rate was studied in order to gain an insight into the growth kinetics. Two different growth regimes were observed for VSS grown Ge nanowires at different temperature ranges. At higher temperatures (345-375 oC), the diffusion or mass transport of germane precursor to the catalyst surface was found to be rate limiting. At lower temperatures (300-345 oC) either the surface reaction or incorporation of Ge at growth step could be rate limiting.
Download or read book The Synthesis of Silicon and Germanium Nanowires for Energy Storage and Single Nanowire Devices written by Dylan Storan and published by . This book was released on 2022 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Strain Engineered Si Ge Nanowire Heterostructures and Josephson Junction Field effect Transistors for Logic Device Applications written by Feng Wen and published by . This book was released on 2020 with total page 412 pages. Available in PDF, EPUB and Kindle. Book excerpt: There has been relentless effort on the physical scaling of silicon (Si) metal-oxide-semiconductor field-effect transistors (MOSFETs) in pursuit of higher computing power in the past decades. Silicon and germanium (Ge) based nanowires are compatible with the standard Si process and promising for the ultimately scaled devices, by allowing the gate-all-around geometry and integration of strain engineering through radial heterostructures to address device-scaling limitations. In the first part of the thesis, advances in probing the strain of radial nanowire heterostructures and carrier mobility enhancement through strain engineering are presented. We present a sequence of structural characterization techniques for Ge-Si [subscript x] Ge [subscript 1-x] and Si-Si [subscript x] Ge [subscript 1-x] core-shell nanowires that extends to all types of Si-Ge radial nanowire heterostructures examined in the thesis. We combine planar and cross-sectional transmission electron microscopy to identify the crystal structure, orientation and morphology of the nanowire heterostructures. We then apply continuum elasticity model to calculate the strain distribution, which coupled with the lattice dynamic theory yields the Ge-Ge or Si-Si Raman modes under strain, showing good agreement with the experimental values acquired via Raman spectroscopy. We also study the electrical properties of Si [subscript x] Ge [subscript 1-x]-Si core-shell nanowires by fabricating and characterizing n-type MOSFETs, and show that the tensile strain in the Si shell leads to a 40% electron mobility enhancement compared to bare Si nanowire MOSFETs. Additionally, we demonstrate both n-type and p-type MOSFETs using Si [subscript x] Ge [subscript 1-x]-Ge-Si core-double-shell nanowires as channel, designed so that holes populate the Ge shell and electrons populate the Si shell, with mobility enhancement of both carriers thanks to the compressive and tensile strain in the respective region. We also extract the valence band offset from the decoupled hole transport in the two shells at low temperature, overcoming the issue that most techniques available to probe the band structure in planar heterostructures are not promptly applicable. Reducing the operation temperature provides an additional path for system optimization in addition to the shrinking of device geometry. In the second part of the thesis, we explore a Boolean logic device suitable for cryogenic computing. We execute a combined effort of modeling and experimental characterization to examine the feasibility of Josephson junction field-effect transistors (JJ-FETs) for logic device applications at low temperatures. JJ-FETs are similar to MOSFETs, with their source and drain electrodes being superconducting at the operation temperature. We develop a compact model for JJ-FETs operating in the short ballistic regime, and perform circuit level simulations to investigate the criteria of signal restoration and fan-out for JJ-FET logic gates. We also experimentally demonstrate the operation of JJ-FETs based on an InAs quantum well heterostructure platform. We perform self-consistent Poisson-Schrödinger simulations, finding different gate voltage regimes where carriers populate one or more subbands in different vertical positions of the heterostructure. Furthermore, we extend the short ballistic model to interpret the experimental data, and discuss the impact of a low oxide/channel interface quality on the implementation of practical JJ-FET logic devices
Download or read book Nanostructuring Silicon and Germanium for High Capacity Anodes in Lithium Ion Batteries written by Justin Thomas Harris and published by . This book was released on 2012 with total page 334 pages. Available in PDF, EPUB and Kindle. Book excerpt: Colloidally synthesized silicon (Si) and germanium (Ge) were explored as high capacity anode materials in lithium ion batteries. a-Si:H particles were synthesized through the thermal decomposition of trisilane in supercritical n-hexane. Precise control over particle size and hydrogen content was demonstrated. Particles ranged in size from 240-1500 nm with hydrogen contents from 10-60 atomic%. Particles with low hydrogen content had some degree of local ordering and were easily crystallized during Raman spectroscopy. The as-synthesized particles did not perform well as an anode material due to low conductivity. Increasing surface conductivity led to enhanced lithiation potential. Cu nanoparticles were deposited on the surface of the a-Si:H particles through a hydrogen facilitated reduction of Cu salts. The resulting Cu coated particles had a lithiation capacity seven times that of pristine a-Si:H particles. Monophenylsilane (MPS) grown Si nanowire paper was annealed under forming gas to reduce a polyphenylsilane shell into conductive carbon. The resulting paper required no binder or carbon additive and achieved capacities of 804 mA h/g vs 8 mA h/g for unannealed wires. Si and Ge heterostructures were explored to take advantage of the higher inherent conductivity of Ge. Ge nanowires were successfully coated with a-Si by thermal decomposition of trisilane on their surface, forming Ge@a-Si core shell structures. The capacity increased with increasing Si loading. The peak lithiation capacity was 1850 mA h/g after 20 cycles -- higher than the theoretical capacity of pure Ge. MPS additives created a thin amorphous shell on the wire surfaces. By incubating the wires after MPS addition the shell was partially reduced, conductivity increased, and a 75% increase in lithiation capacity was observed for the nanowire paper. The syntheses of Bi and Au nanoparticles were also explored. Highly monodisperse Bi nanocrystals were produced with size control from 6-18 nm. The Bi was utilized as seeds for the SLS synthesis of Ge nanorods and copper indium diselenide (CuInSe2) nanowires. Sub 2 nm Au nanocrystals were synthesized. A SQUID magnetometer probed their magnetic behavior. Though bulk Au is diamagnetic, the Au particles were paramagnetic. Magnetic susceptibility increased with decreasing particle diameter.
Download or read book Synthesis of Silicon germanium Nanowires and Field Emission Studies of 1 D Nanostructures written by Joonho Bae and published by . This book was released on 2007 with total page 218 pages. Available in PDF, EPUB and Kindle. Book excerpt: Using the vapor-liquid-solid (VLS) growth method, silicon nanowires and germanium nanowires are grown. We find the high growth rate is responsible for the silicon nanowires with less growth defects when they are grown by use of silicon tetrachloride as a precursor and hydrogen as a carrier gas. Based on this funding, large area, high aspect ratio, h111i oriented silicon nanowires are successfully grown on Si (111) and Si (100). Novel growth mechanisms of VLS growth method were discovered in SiOx nanoflowers and silicon nanocones. In SiOx nanoflowers grown at the tip of silicon nanowires, it is found that they are produced via the enhanced oxidation of silicon at the gold-silicon interface. Furthermore, the analysis of the flower pattern reveals that it is the observation of the dense branching morphology on nanoscale and on spherical geometry. For the silicon nanocones, they are grown by the in situ etching of the catalysts of Ga/Al by HCl during the growth. Scanning electron microscopy (SEM), transmission electron microscopy (TEM) reveal that the nanocones are composed of amorphous silicon oxides and crystalline Si. Based on the similar chemistry of hydrogen reduction of SiCl4 for the growth of silicon nanowires, single crystalline germanium nanowires are grown by use of GeCl4 as a precursor and H2 as a carrier gas. As one of important application of one dimensional nanostructures, the field emission properties of 1-D nanostructures are explored. The field emission properties of a single graphite nanocone are measured in SEM. The inter-electrode separation is controlled using scanning tunneling microscopy (STM) approach method, allowing the precise and ne determination of the separation. Its Fowler-Nordheim plot shows it emits currents in accordance with the Fowler-Nordheim field emission. Its onset voltage, field enhancement factor show that its basic field emission parameters are comparable to those of a single carbon nanotube. It is observed that single nanocone is damaged after emitting a current of about 100 nA, which seems to be due to its hollow interior structure.
Download or read book One Dimensional Nanostructures written by Tianyou Zhai and published by John Wiley & Sons. This book was released on 2012-10-19 with total page 857 pages. Available in PDF, EPUB and Kindle. Book excerpt: Reviews the latest research breakthroughs and applications Since the discovery of carbon nanotubes in 1991, one-dimensional nanostructures have been at the forefront of nanotechnology research, promising to provide the building blocks for a new generation of nanoscale electronic and optoelectronic devices. With contributions from 68 leading international experts, this book reviews both the underlying principles as well as the latest discoveries and applications in the field, presenting the state of the technology. Readers will find expert coverage of all major classes of one-dimensional nanostructures, including carbon nanotubes, semiconductor nanowires, organic molecule nanostructures, polymer nanofibers, peptide nanostructures, and supramolecular nanostructures. Moreover, the book offers unique insights into the future of one-dimensional nanostructures, with expert forecasts of new research breakthroughs and applications. One-Dimensional Nanostructures collects and analyzes a wealth of key research findings and applications, with detailed coverage of: Synthesis Properties Energy applications Photonics and optoelectronics applications Sensing, plasmonics, electronics, and biosciences applications Practical case studies demonstrate how the latest applications work. Tables throughout the book summarize key information, and diagrams enable readers to grasp complex concepts and designs. References at the end of each chapter serve as a gateway to the literature in the field. With its clear explanations of the underlying principles of one-dimensional nanostructures, this book is ideal for students, researchers, and academics in chemistry, physics, materials science, and engineering. Moreover, One-Dimensional Nanostructures will help readers advance their own investigations in order to develop the next generation of applications.
Download or read book Synthesis Assembly and Integration of Semiconductor Nanowires written by Elena P. Pandres and published by . This book was released on 2020 with total page 206 pages. Available in PDF, EPUB and Kindle. Book excerpt: Semiconductor nanowires are a class of highly anisotropic crystalline materials with nanoscale diameters and lengths that range from micrometers to millimeters. The electronic, optical, and mechanical properties of semiconductor nanowires can be considerably different than their bulk counterparts, making them attractive for a range of applications including sensors, energy storage, and quantum information systems. Solution-based synthesis is a promising strategy to produce semiconductor nanowires in a scalable, cost-effective matter. However, many solution-based methods are limited in their ability to produce nanowires with increasingly complex compositions-including doped, alloyed, and heterostructured architectures-as well as to rapidly screen synthetic parameters for combinatorial discovery and optimization. In addition, chemistries and growth dynamics can be difficult to track with nanowire syntheses that require high temperature and extreme pressure equipment. Moreover, the widespread integration of semiconductor nanowires into devices will also require new methods of assembly as well as careful consideration of surface chemistry. After an introduction to current methods of semiconductor nanowire synthesis, existing tactics for nanowire assembly, and strategies to improve the energy density of lithium ion batteries with group IV nanomaterials, this dissertation will cover three main topics related to (i) new synthetic methods for nanowire growth, (ii) a novel light-based nanowire assembly process, and (iii) the integration of nanowires into high-energy-density composite electrodes for lithium ion batteries. Herein, we demonstrate a new continuous-flow, laser-driven, nanowire growth process that exploits the light absorption of colloidal metal nanocrystals to drive semiconductor nanowire growth in an optically accessible reactor on the benchtop, potentially opening the door for both rapid screening of synthetic parameters as well as in situ studies of nanowire growth dynamics. Investigations of solution-based nanowire growth using this system establish that laser-driven syntheses can achieve rapid, on-demand growth of semiconductor nanowires. Importantly, the integration of nanowires into future device architectures will require a wide range of assembly strategies. While current solution-based nanowire assembly processes struggle to create deterministic heterojunctions, here, we demonstrate a novel example of nanowire assembly in a high-Prandtl-number organic solvent system, using an optical trap to orient, align, and "solder" metal-seeded semiconductor nanowires into periodic axial heterostructures. Finally, we investigate the role of surface functionalization on the integration of group-IV nanowires into high-capacity alloying electrodes for lithium ion batteries. We demonstrate that interfacial chemistry affects electrochemical access to different phases of lithiated germanium, and by carefully controlling the nanowire surface chemistry, we eliminate the need for the fluorinated electrolyte additives typically required for the stable cycling of group-IV-based, lithium-ion battery electrodes. In addition, we demonstrate that by balancing precursor decomposition kinetics, alloyed silicon-germanium (SiGe) nanowires can be synthesized through supercritical-fluid-based processes, potentially improving the rate capability of high-capacity silicon-based electrode materials produced via scalable processes. We anticipate that the information gained from these solution-based synthetic methods, assembly techniques, and surface chemistry studies will inform synthetic compositional control, elucidate relationships between solution-based reaction parameters and emergent properties, and advance the integration of solution-grown semiconductor nanowires into next-generation devices.
Download or read book CMOSET 2013 Abstracts written by CMOS Emerging Technologies Research and published by CMOS Emerging Technologies. This book was released on with total page 70 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Handbook of Nanomaterials Properties written by Bharat Bhushan and published by Springer Science & Business Media. This book was released on 2014-03-13 with total page 1467 pages. Available in PDF, EPUB and Kindle. Book excerpt: Nanomaterials attract tremendous attention in recent researches. Although extensive research has been done in this field it still lacks a comprehensive reference work that presents data on properties of different Nanomaterials. This Handbook of Nanomaterials Properties will be the first single reference work that brings together the various properties with wide breadth and scope.
Download or read book Nanowires written by Anqi Zhang and published by Springer. This book was released on 2016-07-26 with total page 327 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book provides a comprehensive summary of nanowire research in the past decade, from the nanowire synthesis, characterization, assembly, to the device applications. In particular, the developments of complex/modulated nanowire structures, the assembly of hierarchical nanowire arrays, and the applications in the fields of nanoelectronics, nanophotonics, quantum devices, nano-enabled energy, and nano-bio interfaces, are focused. Moreover, novel nanowire building blocks for the future/emerging nanoscience and nanotechnology are also discussed.Semiconducting nanowires represent one of the most interesting research directions in nanoscience and nanotechnology, with capabilities of realizing structural and functional complexity through rational design and synthesis. The exquisite control of chemical composition, morphology, structure, doping and assembly, as well as incorporation with other materials, offer a variety of nanoscale building blocks with unique properties.
Download or read book Growth and Characterization of Silicon and Germanium Nanowires and Heterostructures written by Prashanth Madras and published by . This book was released on 2010 with total page 346 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Nanowires and Nanobelts written by Zhong Lin Wang and published by Springer Science & Business Media. This book was released on 2013-06-05 with total page 482 pages. Available in PDF, EPUB and Kindle. Book excerpt: Volume 1, Metal and Semiconductor Nanowires covers a wide range of materials systems, from noble metals (such as Au, Ag, Cu), single element semiconductors (such as Si and Ge), compound semiconductors (such as InP, CdS and GaAs as well as heterostructures), nitrides (such as GaN and Si3N4) to carbides (such as SiC). The objective of this volume is to cover the synthesis, properties and device applications of nanowires based on metal and semiconductor materials. The volume starts with a review on novel electronic and optical nanodevices, nanosensors and logic circuits that have been built using individual nanowires as building blocks. Then, the theoretical background for electrical properties and mechanical properties of nanowires is given. The molecular nanowires, their quantized conductance, and metallic nanowires synthesized by chemical technique will be introduced next. Finally, the volume covers the synthesis and properties of semiconductor and nitrides nanowires.
