Download or read book Switched opamp based CMOS Sample and hold Circuit Design written by Liang Dai and published by . This book was released on 1998 with total page 142 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Analog Circuit Design written by Johan Huijsing and published by Springer Science & Business Media. This book was released on 2013-04-17 with total page 447 pages. Available in PDF, EPUB and Kindle. Book excerpt: Many interesting design trends are shown by the six papers on operational amplifiers (Op Amps). Firstly. there is the line of stand-alone Op Amps using a bipolar IC technology which combines high-frequency and high voltage. This line is represented in papers by Bill Gross and Derek Bowers. Bill Gross shows an improved high-frequency compensation technique of a high quality three stage Op Amp. Derek Bowers improves the gain and frequency behaviour of the stages of a two-stage Op Amp. Both papers also present trends in current-mode feedback Op Amps. Low-voltage bipolar Op Amp design is presented by leroen Fonderie. He shows how multipath nested Miller compensation can be applied to turn rail-to-rail input and output stages into high quality low-voltage Op Amps. Two papers on CMOS Op Amps by Michael Steyaert and Klaas Bult show how high speed and high gain VLSI building blocks can be realised. Without departing from a single-stage OT A structure with a folded cascode output, a thorough high frequency design technique and a gain-boosting technique contributed to the high-speed and the high-gain achieved with these Op Amps. . Finally. Rinaldo Castello shows us how to provide output power with CMOS buffer amplifiers. The combination of class A and AB stages in a multipath nested Miller structure provides the required linearity and bandwidth.
Download or read book Design of Low Voltage CMOS Switched Opamp Switched Capacitor Systems written by Vincent S.L. Cheung and published by Springer Science & Business Media. This book was released on 2013-03-14 with total page 207 pages. Available in PDF, EPUB and Kindle. Book excerpt: This volume emphasizes the design and development of advanced switched-opamp architectures and techniques for low-voltage low-power switched-capacitor systems. It presents a novel multi-phase switched-opamp technique together with new system architectures that are critical in improving significantly the performance of switched-capacitor systems at low supply voltages.
Download or read book Design of Low Voltage Low Power CMOS Delta Sigma A D Converters written by Vincenzo Peluso and published by Springer Science & Business Media. This book was released on 2013-03-09 with total page 178 pages. Available in PDF, EPUB and Kindle. Book excerpt: Design of Low-Voltage Low-Power CMOS Delta-Sigma A/D Converters investigates the feasibility of designing Delta-Sigma Analog to Digital Converters for very low supply voltage (lower than 1.5V) and low power operation in standard CMOS processes. The chosen technique of implementation is the Switched Opamp Technique which provides Switched Capacitor operation at low supply voltage without the need to apply voltage multipliers or low VtMOST devices. A method of implementing the classic single loop and cascaded Delta-Sigma modulator topologies with half delay integrators is presented. Those topologies are studied in order to find the parameters that maximise the performance in terms of peak SNR. Based on a linear model, the performance degradations of higher order single loop and cascaded modulators, compared to a hypothetical ideal modulator, are quantified. An overview of low voltage Switched Capacitor design techniques, such as the use of voltage multipliers, low VtMOST devices and the Switched Opamp Technique, is given. An in-depth discussion of the present status of the Switched Opamp Technique covers the single-ended Original Switched Opamp Technique, the Modified Switched Opamp Technique, which allows lower supply voltage operation, and differential implementation including common mode control techniques. The restrictions imposed on the analog circuits by low supply voltage operation are investigated. Several low voltage circuit building blocks, some of which are new, are discussed. A new low voltage class AB OTA, especially suited for differential Switched Opamp applications, together with a common mode feedback amplifier and a comparator are presented and analyzed. As part of a systematic top-down design approach, the non-ideal charge transfer of the Switched Opamp integrator cell is modeled, based upon several models of the main opamp non-ideal characteristics. Behavioral simulations carried out with these models yield the required opamp specifications that ensure that the intended performance is met in an implementation. A power consumption analysis is performed. The influence of all design parameters, especially the low power supply voltage, is highlighted. Design guidelines towards low power operation are distilled. Two implementations are presented together with measurement results. The first one is a single-ended implementation of a Delta-Sigma ADC operating with 1.5V supply voltage and consuming 100 &mgr;W for a 74 dB dynamic range in a 3.4 kHz bandwidth. The second implementation is differential and operates with 900 mV. It achieves 77 dB dynamic range in 16 kHz bandwidth and consumes 40 &mgr;W. Design of Low-Voltage Low-Power CMOS Delta-Sigma A/D Converters is essential reading for analog design engineers and researchers.
Download or read book Demystifying Switched Capacitor Circuits written by Mingliang (Michael) Liu and published by Elsevier. This book was released on 2006-06-12 with total page 332 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book helps engineers to grasp fundamental theories and design principles by presenting physical and intuitive explanations of switched-capacitor circuits. Numerous circuit examples are discussed and the author emphasizes the most important and fundamental principles involved in implementing state-of-the-art switched-capacitor circuits for analog signal processing and power management applications. Throughout the book, the author presents numerous step-by-step tutorials and gives practical design examples.While some quantitative analysis is necessary to understand underlying concepts, tedious mathematical equations and formal proofs are avoided. An intuitive appreciation for switched-capacitor circuits is achieved.Much of the existing information on contemporary switched-capacitor circuit applications is in the form of applications notes and data sheets for various switched-capacitor ICs. This book compiles such information in a single volume and coherently organizes and structures it.The author has his own website at www.mingliangliu.com * Step-by-step tutorials which emphasize the most fundamental principals of switched-capacitor circuits * Few tedious mathematical equations * The first easy-to-understand compilation on this subject--most information available is not very cohesive
Download or read book Introduction to CMOS OP AMPs and Comparators written by Roubik Gregorian and published by Wiley-Interscience. This book was released on 1999-02-26 with total page 392 pages. Available in PDF, EPUB and Kindle. Book excerpt: A step-by-step guide to the design and analysis of CMOS operational amplifiers and comparators This volume is a comprehensive text that offers a detailed treatment of the analysis and design principles of two of the most important components of analog metal oxide semiconductor (MOS) circuits, namely operational amplifiers (op-amps) and comparators. The book covers the physical operation of these components, their design procedures, and applications to analog MOS circuits-particularly those involving switched-capacitor circuits, and analog-to-digital (A/D) and digital-to-analog (D/A) converters. Roubik Gregorian, a leading authority in the field, gives circuit designers the technical knowledge they need to design high-performance op-amps and comparators suitable for most analog circuit applications. In this self-contained treatment, which is loosely based on his well-received 1986 book, Analog MOS Integrated Circuits for Signal Processing (coauthored with Gabor C. Temes), Gregorian reviews the required basics before advancing to state-of-the-art topics and problem-solving techniques. This valuable guide: * Clearly explains configuration and performance limitation issues affecting the operation of CMOS op-amps and comparators * Details advanced design procedures to improve performance * Provides practical design examples suitable for a broad range of analog circuit applications * Incorporates hundreds of illustrations into the text * Concludes each chapter with problems and references to advanced topics, useful in textbook adoptions Introduction to CMOS Op-Amps and Comparators is invaluable for analog and mixed-signal designers, for senior and graduate students in electrical engineering, and for anyone who would like to keep up with this essential technology.
Download or read book Design of Very High Frequency Multirate Switched Capacitor Circuits written by Seng-Pan U and published by Springer Science & Business Media. This book was released on 2006 with total page 268 pages. Available in PDF, EPUB and Kindle. Book excerpt: Design of Very High-Frequency Multirate Switched-Capacitor Circuits presents the theory and the corresponding CMOS implementation of the novel multirate sampled-data analog interpolation technique which has its great potential on very high-frequency analog frond-end filtering due to its inherent dual advantage of reducing the speed of data-converters and DSP core together with the specification relaxation of the post continuous-time filtering. This technique completely eliminates the traditional phenomenon of sampled-and-hold frequency-shaping at the lower input sampling rate. Also, in order to tackle physical IC imperfections at very high frequency, the state-of-the-art circuit design and layout techniques for high-speed Switched-Capacitor (SC) circuits are comprehensively discussed: -Optimum circuit architecture tradeoff analysis -Simple speed and power trade-off analysis of active elements -High-order filtering response accuracy with respect to capacitor-ratio mismatches -Time-interleaved effect with respect to gain and offset mismatch -Time-interleaved effect with respect to timing-skew and random jitter with non-uniformly holding -Stage noise analysis and allocation scheme -Substrate and supply noise reduction -Gain-and offset-compensation techniques -High-bandwidth low-power amplifier design and layout -Very low timing-skew multiphase generation Two tailor-made optimum design examples in CMOS are presented. The first one achieves a 3-stage 8-fold SC interpolating filter with 5.5MHz bandwidth and 108MHz output sampling rate for a NTSC/PAL CCIR 601 digital video at 3 V. Another is a 15-tap 57MHz SC FIR bandpass interpolating filter with 4-fold sampling rate increase to 320MHz and the first-time embedded frequency band up-translation for DDFS system at 2.5V. The corresponding chip prototype achieves so far the highest operating frequency, highest filter order and highest center frequency with highest dynamic range under the lowest supply voltage when compared to the previously reported high-frequency SC filters in CMOS.
Download or read book Design of an Opamp with Very Low Power Dissipation written by Shivani Aggarwal and published by LAP Lambert Academic Publishing. This book was released on 2015-07 with total page 104 pages. Available in PDF, EPUB and Kindle. Book excerpt: The Operational Amplifier is more versatile and important building blocks in analog circuit design. Operational amplifiers (OpAmps) are integral part of many analog and mixed signal systems. Op amps with vastly different levels of complexity used to realize functions high speed amplifier ranging from dc bias generation to or filtering. The design of an opAmp continues to pose a challenge as the supply voltage and transistor channel lengths scale down with each generation of CMOS technologies. A wide variety of electronic applications deal with small signal inputs. Operational amplifiers are amplifiers that have sufficiently high forward gain.For most of the analog systems and mixed signal ICs, OpAmps are used for the comparator and switched capacitor based sample and hold circuits. The motivation for the design of OpAmp includes a wide area of application ranging from home appliances to biomedical, communication and signal processing purposes.Designers always make a tradeoff between performance parameters while designing an OpAmp.
Download or read book Op Amps for Everyone written by Ron Mancini and published by Newnes. This book was released on 2003 with total page 470 pages. Available in PDF, EPUB and Kindle. Book excerpt: The operational amplifier ("op amp") is the most versatile and widely used type of analog IC, used in audio and voltage amplifiers, signal conditioners, signal converters, oscillators, and analog computing systems. Almost every electronic device uses at least one op amp. This book is Texas Instruments' complete professional-level tutorial and reference to operational amplifier theory and applications. Among the topics covered are basic op amp physics (including reviews of current and voltage division, Thevenin's theorem, and transistor models), idealized op amp operation and configuration, feedback theory and methods, single and dual supply operation, understanding op amp parameters, minimizing noise in op amp circuits, and practical applications such as instrumentation amplifiers, signal conditioning, oscillators, active filters, load and level conversions, and analog computing. There is also extensive coverage of circuit construction techniques, including circuit board design, grounding, input and output isolation, using decoupling capacitors, and frequency characteristics of passive components. The material in this book is applicable to all op amp ICs from all manufacturers, not just TI. Unlike textbook treatments of op amp theory that tend to focus on idealized op amp models and configuration, this title uses idealized models only when necessary to explain op amp theory. The bulk of this book is on real-world op amps and their applications; considerations such as thermal effects, circuit noise, circuit buffering, selection of appropriate op amps for a given application, and unexpected effects in passive components are all discussed in detail. *Published in conjunction with Texas Instruments *A single volume, professional-level guide to op amp theory and applications *Covers circuit board layout techniques for manufacturing op amp circuits.
Download or read book Circuit Techniques for Low Voltage and High Speed A D Converters written by Mikko E. Waltari and published by Springer Science & Business Media. This book was released on 2005-12-30 with total page 256 pages. Available in PDF, EPUB and Kindle. Book excerpt: This useful monograph presents a total of seven prototypes: two double-sampled S/H circuits, a time-interleaved ADC, an IF-sampling self-calibrated pipelined ADC, a current steering DAC with a deglitcher, and two pipelined ADCs employing the SO techniques.
Download or read book CMOS Current Mode Circuits for Data Communications written by Fei Yuan and published by Springer Science & Business Media. This book was released on 2007-04-26 with total page 306 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book deals with the analysis and design of CMOS current-mode circuits for data communications. CMOS current-mode sampled-data networks, i.e. switched-current circuits, are excluded. Major subjects covered in the book include: a critical comparison of voltage-mode and current-mode circuits; the building blocks of current-mode circuits: design techniques; modeling of wire channels, electrical signaling for Gbps data communications; ESD protection for current-mode circuits and more. This book will appeal to IC design engineers, hardware system engineers and others.
Download or read book Low Voltage Leakage Insensitive Switched opamp Sample and Hold written by Robert Lewis Crawford and published by . This book was released on 2010 with total page 332 pages. Available in PDF, EPUB and Kindle. Book excerpt: The work presented here shows that using Switched Opamp topologies in low voltage, switched capacitor circuits possesses a robust immunity to off-state switch lea¬kage mechanisms. A 1V Switched Opamp Sample and Hold is simulated, and its leakage immunity to a input sampling transmission gate is evaluated in terms of bit resolution. Additionally, a charge compensation circuit is introduced that can quickly recover the biasing levels such that higher switching speeds are no longer limited by having to re¬charge the D.C. bias. The simulations performed here in Cadence 5.1 using 0.18 um CMOS show that without any leakage immunity capability, a transmission gate, (in this case purposely de¬signed to have high off-state leakage) will leak into a sampling capacitor enough such that a bit resolution of only 1-bit is possible during the hold time for a 10 MHz switching operation. However, when the same sampling capacitor and transmission gate are used in the Switched Opamp Sample and Hold circuit designed for 9-bit resolution at 10 MHz, the circuit maintains the 9-bit resolution. Simulations of a 1 MHz sine wave sampling at 10 MHz at various amplitudes up to± 500 mV , with and without the charge compensation circuit, show that the charge compensation circuitry recovers the bias in time.
Download or read book Analog Integrated Circuit Design written by Alan B. Grebene and published by . This book was released on 1972 with total page 422 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Analog Circuit Design written by Michiel Steyaert and published by Springer Science & Business Media. This book was released on 2006-01-18 with total page 434 pages. Available in PDF, EPUB and Kindle. Book excerpt: Analog Circuit Design contains the contribution of 18 tutorials of the 14th workshop on Advances in Analog Circuit Design. Each part discusses a specific todate topic on new and valuable design ideas in the area of analog circuit design. Each part is presented by six experts in that field and state of the art information is shared and overviewed. This book is number 14 in this successful series of Analog Circuit Design, providing valuable information and excellent overviews of analog circuit design, CAD and RF systems. Analog Circuit Design is an essential reference source for analog circuit designers and researchers wishing to keep abreast with the latest development in the field. The tutorial coverage also makes it suitable for use in an advanced design course.
Download or read book Design of High Performance CMOS Voltage Controlled Oscillators written by Liang Dai and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 170 pages. Available in PDF, EPUB and Kindle. Book excerpt: Design of High-Performance CMOS Voltage-Controlled Oscillators presents a phase noise modeling framework for CMOS ring oscillators. The analysis considers both linear and nonlinear operation. It indicates that fast rail-to-rail switching has to be achieved to minimize phase noise. Additionally, in conventional design the flicker noise in the bias circuit can potentially dominate the phase noise at low offset frequencies. Therefore, for narrow bandwidth PLLs, noise up conversion for the bias circuits should be minimized. We define the effective Q factor (Qeff) for ring oscillators and predict its increase for CMOS processes with smaller feature sizes. Our phase noise analysis is validated via simulation and measurement results. The digital switching noise coupled through the power supply and substrate is usually the dominant source of clock jitter. Improving the supply and substrate noise immunity of a PLL is a challenging job in hostile environments such as a microprocessor chip where millions of digital gates are present.
Download or read book Design of CMOS Operational Amplifiers written by Rasoul Dehghani and published by Artech House. This book was released on 2013 with total page 206 pages. Available in PDF, EPUB and Kindle. Book excerpt: CMOS operational amplifiers (Op Amps) are one of the most important building blocks in many of todays integrated circuits. This cutting-edge volume provides you with an analytical method for designing CMOS Op Amp circuits, placing emphasis on the practical aspects of the design process. This unique book takes an in-depth look at CMOS differential amplifiers, explaining how they are the main part of all Op Amps. The book presents important details and a design method for the different architectures of single ended Op Amps. You find complete chapters dedicated to the critical issues of CMOS output stages, fully differential Op Amps, and CMOS reference generators. This comprehensive book also includes an introduction to CMOS technology and the basics of the physical aspects of MOS transistors, providing you with the foundation needed to fully master the material.
Download or read book CMOS written by R. Jacob Baker and published by John Wiley & Sons. This book was released on 2008 with total page 1074 pages. Available in PDF, EPUB and Kindle. Book excerpt: This edition provides an important contemporary view of a wide range of analog/digital circuit blocks, the BSIM model, data converter architectures, and more. The authors develop design techniques for both long- and short-channel CMOS technologies and then compare the two.
