Download or read book Stress Redistribution Capability in Structural Glazing Joints written by Kun Chang and published by . This book was released on 1990 with total page 232 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Stress Redistribution in Structural Glazing Joints written by K. Chang and published by . This book was released on 1992 with total page 9 pages. Available in PDF, EPUB and Kindle. Book excerpt: This paper examines the behavior of structural sealant glazing joints loaded to failure. Experimental data are presented from a beam analog for a structural sealant glazed window edge. Analytical results are given for a typical structural sealant glazed unit. The characteristic, service load level, "double-hump" stress and elongation pattern along the glass edge was simulated by a tee-beam specimen with the stem and flange joined by a silicone bead. Point loads were used to produce a double-hump elongation pattern. The results clearly showed the ability of a structural sealant joint to redistribute stresses along its length when loaded to failure. A finite element analysis was made of stress redistribution along the edges of a structural sealant glazed unit under negative wind overloading, approximating a failure condition in the sealant joint. The model included a full stress range, combined tension and shear model for the joints and geometric nonlinearity in the glass. Transverse shear deformations of the joint, due to geometric nonlinearity, were found to have a significant effect on the tensile response of the joint. As a result, the extensive redistribution of tensile stresses seen in the tee-beam specimen did not develop. Instead, only a partial spreading of the double-hump pattern was seen. The implications of the research results are discussed.

Download or read book Science and Technology of Building Seals Sealants Glazing and Waterproofing written by Charles J. Parise and published by ASTM International. This book was released on 1992 with total page 169 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Analysis of Stress Redistribution in Structural Silicone Glazing Systems written by Mark A. De Clercq and published by . This book was released on 1990 with total page 232 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Science and Technology of Building Seals Sealants Glazing and Waterproofing written by and published by . This book was released on 1992 with total page 184 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Sealants in Construction written by Jerome Klosowski and published by CRC Press. This book was released on 2016-01-05 with total page 419 pages. Available in PDF, EPUB and Kindle. Book excerpt: Revised Bestseller Offers Broad-Based Knowledge to a Wide Range of Technical ProfessionalsThe definitive guide to sealing operations in construction, this latest edition of Sealants in Construction focuses on the most current technology, methods, applications, and standards relevant to sealant performance. Providing guided direction on how to choos

Download or read book Challenging Glass 3 written by Freek Bos and published by IOS Press. This book was released on 2012 with total page 1022 pages. Available in PDF, EPUB and Kindle. Book excerpt: There are two things everybody knows about glass: it is transparent, and it breaks! These are also the properties that constitute the challenge of glass as an architectural and structural material. This book presents papers from the third Challenging Glass Conference (CGC3), held at the Technical University (TU) Delft, the Netherlands, in June 2012. The conference brings together glass engineering, research and design specialists. Papers are grouped under seven topic headings: project and case studies; joints, fixings and adhesives; strength, stability and safety (a category which includes a quarter of all the papers presented at the conference); laminates and composite design; curved and bended glass; architectural design and lighting and finally, glass in facades. Glass remains one of the most exciting materials available to designers and architects today. This book will be of interest to all those involved in working with glass in an architectural and structural context.

Download or read book Structural Adhesive Joints in Engineering written by R. D. Adams and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 317 pages. Available in PDF, EPUB and Kindle. Book excerpt: The intention of this book is that it should contain everything an engineer needs to know to be able to design and produce adhesively bonded joints which are required to carry significant loads. The advan tages and disadvantages of bonding are given, together with a sufficient understanding of the necessary mechanics and chemistry to enable the designer to make a sound engineering judgement in any particular case. The stresses in joints are discussed extensively so that the engineer can get sufficient philosophy or feel for them, or can delve more deeply into the mathematics to obtain quantitative solutions even with elasto plastic behaviour. A critical description is given of standard methods of testing adhesives, both destructively and non-destructively. The essen tial chemistry of adhesives and the importance of surface preparation are described and guidance is given for adhesive selection by me ans of check lists. For many applications, there will not be a unique adhesive which alone is suitable, and factors such as cost, convenience, produc tion considerations or familiarity may be decisive. A list of applications is given as examples. The authors wish to increase the confidence of engineers using adhesive bonding in load-bearing applications by the information and experience presented. With increasing experience of adhesives en gineering, design will become more elegant as weH as more fitted to its products.

Download or read book Structural Use of Glass written by Matthias Haldimann and published by IABSE. This book was released on 2008 with total page 226 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book attempts to redress this issue by providing an overview of the recent developments in this field thereby providing a basis for the understanding of the structural performance and design of glass in buildings. Each chapter draws on the latest developments in practice and research and contains contributions from various international glass experts. The mix of general and specialist content ranging from rules of thumb to fracture mechanics and novel applications to post-breakage performance make this book useful to practitioners and researchers. Furthermore, the text is supplemented by tables of the major codes of practice and by an extensive list of references.

Download or read book COST Action TU0905 Mid term Conference on Structural Glass written by Jan Belis and published by CRC Press. This book was released on 2013-04-05 with total page 602 pages. Available in PDF, EPUB and Kindle. Book excerpt: The application of glass as a structural material may seem surprising initially, yet pioneering glass structures were first built two decades ago already. Ever since, Structural Glass has been developing at a very high pace thanks to very intensive scientific and industrial research and new technological developments. Right at the heart of these rapidly evolving developments, the European COST Action TU0905 'Structural Glass – Novel Design Methods and Next Generation Products' is active. With its main goals of unifying, harmonizing and boosting the ongoing developments in structural glass research, COST Action TU0905 frequently organizes international expert meetings and Training Schools, and supports scientific research missions. This proceedings volume of the COST Action TU0905 Mid-term Conference on Structural Glass offers a great insight into the latest developments in Structural Glass by means of more than 60 peer-reviewed papers by nearly 140 authors. Contributions cover all major topics in the field, ranging from in-depth material investigations to full glass structures and facades. As such, it represents an appealing work on this very young and dynamic field, and is intended for a global readership of researchers and practitioners, including structural and civil engineers, architects, material scientists, building consultants, contractors, material suppliers and product manufacturers, as well as other professionals involved in the design and realization of structural glass projects. The COST Action TU0905 Mid-Term Conference was held as a unique event, strongly embedded in COST Action TU0905 'Structural Glass – Novel Design Methods and Next Generation Products'. As such, it reflects the Action’s strong position as probably the largest Structural Glass research network worldwide, and disseminates the ultimate COST philosophy: true cooperation in Science and Technology.

Download or read book A Load Displacement Model for Structural Glazing Joints in Tension and Shear written by LB. Sandberg and published by . This book was released on 1992 with total page 12 pages. Available in PDF, EPUB and Kindle. Book excerpt: An empirically based load-displacement model for typical silicone structural glazing joints is presented. The model is capable of simulating behavior under combined tensile and transverse shear loadings up to failure. Load and displacement are related by exponential equations of the form, F = A(1 - exp-B?). In this equation, F is the applied force (either tensile or shear). A and B are functions of tensile and shear displacements. The pairs of functions for tensile force and shear force are different. ? is the resultant of tensile and shear displacements. The forms and constants for the functions A and B were obtained by regression analyses of test data at six different combinations of tensile and shear displacement, from pure tension to pure shear. An exponential equation with constants for A and B was fit to the data for each displacement combination. The constants were plotted versus a measure of relative tensile and shear displacements. Curves fit to these plots define the approximate expressions for A and B under any set of tensile and shear displacements below the failure limit. Comparisons of the model with the experimental data are shown. A simplified approach to obtaining the load-displacement model is also proposed and compared to experimental data. The application of the model to analysis of joint behavior in structural glazing systems is briefly discussed.

Download or read book Advances and Trends in Engineering Sciences and Technologies II written by Mohamad Ali and published by CRC Press. This book was released on 2016-11-30 with total page 880 pages. Available in PDF, EPUB and Kindle. Book excerpt: These are the proceedings of the 2nd International Conference on Engineering Sciences and Technologies (ESaT 2016), held from 29th of June until the 1st of July 2016 in the scenic High Tatras Mountains, Tatranské Matliare, Slovak Republic. After the successful implementation and excellent feedback of the first international conference ESaT 2015, ESaT 2016 was organized under the auspices of the Faculty of Civil Engineering, Technical University of Košice, Slovak Republic in collaboration with the University of Miskolc, Hungary. The conference focused on a wide spectrum of topics and subject areas in civil engineering sciences. The proceedings bringing new and original advances and trends in various fields of engineering sciences and technologies that accost a wide range of academics, scientists, researchers and professionals from universities and practice. The authors of the articles originate from different countries around the world guaranteeing the importance, topicality, quality and level of presented results.

Download or read book Advances in the Analysis and Design of Marine Structures written by J. W. Ringsberg and published by CRC Press. This book was released on 2023-04-14 with total page 921 pages. Available in PDF, EPUB and Kindle. Book excerpt: Advances in the Analysis and Design of Marine Structures is a collection of papers presented at MARSTRUCT 2023, the 9th International Conference on Marine Structures, held in Gothenburg, Sweden, 3-5 April 2023. The conference was organised by the Division of Marine Technology, Department of Mechanics and Maritime Sciences at Chalmers University of Technology, in Gothenburg, Sweden. The MARSTRUCT Conference series deals with Ship and Offshore Structures, addressing topics in the fields of: Methods and tools for loads and load effects Methods and tools for strength assessment Experimental analysis of structures Materials and fabrication of structures Methods and tools for structural design and optimization Structural reliability, safety, and environmental protection The MARSTRUCT conferences series of started in Glasgow, UK in 2007, the second event of the series took place in Lisbon, Portugal in March 2009, the third in Hamburg, Germany in March 2011, the fourth in Espoo, Finland in March 2013, the fifth in Southampton, UK in March 2015, the sixth in Lisbon, Portugal in May 2017, the seventh in Dubrovnik, Croatia in May 2019, and the eighth event in Trondheim, Norway in June 2021. Advances in the Analysis and Design of Marine Structures is essential reading for academics, engineers and all professionals involved in the design of marine and offshore structures. The Proceedings in Marine Technology and Ocean Engineering series is devoted to the publication of proceedings of peer-reviewed international conferences dealing with various aspects of ‘Marine Technology and Ocean Engineering’. The Series includes the proceedings of the following conferences: the International Maritime Association of the Mediterranean (IMAM) Conferences, the Marine Structures (MARSTRUCT) Conferences, the Renewable Energies Offshore (RENEW) Conferences and the Maritime Technology (MARTECH) Conferences. The ‘Marine Technology and Ocean Engineering’ series is also open to new conferences that cover topics on the sustainable exploration and exploitation of marine resources in various fields, such as maritime transport and ports, usage of the ocean including coastal areas, nautical activities, the exploration and exploitation of mineral resources, the protection of the marine environment and its resources, and risk analysis, safety and reliability. The aim of the series is to stimulate advanced education and training through the wide dissemination of the results of scientific research.

Download or read book Rehabilitation of Metallic Structural Systems Using Fiber Reinforced Polymer FRP Composites written by Vistasp M. Karbhari and published by Elsevier. This book was released on 2024-11-01 with total page 656 pages. Available in PDF, EPUB and Kindle. Book excerpt: Rehabilitation of Metallic Structural Systems Using Fiber-Reinforced Polymer (FRP) Composites, Second Edition provides comprehensive knowledge on the application of FRPs in various types of metallic field structures. Part I provides an overview of the various types of materials and systems and discusses the durability of bonds. Part II focuses on materials-level considerations, such as corrosion and mechanical behavior, putty effects on the effectiveness of pipeline systems, laser joining and the use of carbon and basalt FRP for underwater repair. Building on Part II, the final three sections focus on applications of FRP composites to steel components and various infrastructure systems. This book will be a standard reference for civil engineers, designers, materials scientists, and other professionals who are involved in the rehabilitation of metallic structures using fiber reinforced polymer composites. Contains eighteen new chapters covering materials-level aspects and applications Presents materials developments for tailored bonds, durability, and bond behavior Includes methods of analysis, testing, and implementation across a broad range of sectors Covers design aspects, guidelines, and codes Discusses economic aspects and future prospects

Download or read book Handbook of Adhesives and Sealants written by Philippe Cognard and published by Elsevier. This book was released on 2006-08-30 with total page 530 pages. Available in PDF, EPUB and Kindle. Book excerpt: Contributions from more than 60 authors, each a well-known specialist in their field, have been co-ordinated to produce the most comprehensive Handbook of Adhesives and Sealants ever published. The handbook will be published as 8 volumes, over a period of 4 years and will contain over 2800 pages, rich with case studies, industrial applications and the latest research. It is a work in progress, enabling the latest new and important applications to be included as they happen. Volume 2 of Elsevier’s Handbook of Adhesives & Sealants Series, General knowledge, application of adhesives & new curing techniques, covers the mechanisms of adhesion, its application, and drying and curing techniques. The volume is divided in to the following sections: • Theory of adhesion • Metering and dispensing • Design and calculation of bonded joints• Heat stable adhesives• UV curing • Flexible bonding and sealants Each contributing author is a scientist, practitioner, engineer, or chemist with an abundance of practical experience in their respective field, making this text an authoritative reference source for any materials scientist or engineer, whether in academia or industry.

Download or read book Building Science Abstracts written by and published by . This book was released on 1931 with total page 558 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Building Structures written by Malcolm Millais and published by Routledge. This book was released on 2017-07-14 with total page 568 pages. Available in PDF, EPUB and Kindle. Book excerpt: This is a one-stop book for knowing everything important about building structures. Self-contained and with no prerequisites needed, it is suitable for both general readers and building professionals. follow the history of structural understanding; grasp the concepts of structural behaviour via step-by-step explanations; apply these concepts to a simple building; see how these concepts apply to real buildings, from Durham Cathedral to the Bank of China; use these concepts to define the design process; see how these concepts inform design choices; understand how engineering and architecture have diverged, and what effect this had; learn to do simple but relevant numerical calculations for actual structures; understand when dynamics are important; follow the development of progressive collapse prevention; enter the world of modern structural theory; see how computers can be used for structural analysis; learn how to organise and design a successful project. With more than 500 pages and over 1100 user-friendly diagrams, this book is a must for anyone who would like to understand the fascinating world of structures.