Download or read book Stress Intensity Factor Dependence of Hg Al Liquid Metal Embrittlment sic written by Scott G. Keller and published by . This book was released on 2009 with total page 146 pages. Available in PDF, EPUB and Kindle. Book excerpt: When high strength aluminum alloys are subjected to liquid metals, physical and chemical reactions ensue resulting in what is known as liquid metal embrittlement (LME). A subset of environmentally-assisted cracking, LME is exhibited when a liquid metal, e.g. Hg or Ga, comes into intimate contact with a solid metal having significant susceptibility. As mechanical loads are applied, the interaction between the two metals results in a reduction in the flow properties of the solid metal. Several theories have been proposed to identify the underlying microstructural failure mechanism; however, none have been widely accepted, as failures can typically incorporate features common to several failure theories. In an effort to confirm, extend or replace the physically-based theories, fracture mechanics experiments on Al 7075-T651 in liquid mercury have been conducted. Experiments were conducted in a custom environmental chamber capable of exposing specimens to liquid environments while applying a mechanical load. Through both plane-strain fracture and stress intensity factor-dependent (SIF) tests, fracture toughness values along with incubation periods were analyzed and provided data for a load-based theory of LME. These mechanical test data, along with metallographic analysis, show that the phenomena of LME is both strongly time- and SIF-dependent.
Download or read book Metals Abstracts written by and published by . This book was released on 1998 with total page 1042 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Scientific and Technical Aerospace Reports written by and published by . This book was released on 1984 with total page 1278 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Mechanical Behaviour of Engineering Materials written by Joachim Roesler and published by Springer Science & Business Media. This book was released on 2007-10-16 with total page 540 pages. Available in PDF, EPUB and Kindle. Book excerpt: How do engineering materials deform when bearing mechanical loads? To answer this crucial question, the book bridges the gap between continuum mechanics and materials science. The different kinds of material deformation are explained in detail. The book also discusses the physical processes occurring during the deformation of all classes of engineering materials and shows how these materials can be strengthened to meet the design requirements. It provides the knowledge needed in selecting the appropriate engineering material for a certain design problem. This book is both a valuable textbook and a useful reference for graduate students and practising engineers.
Download or read book Fracture mechanics of concrete Structural application and numerical calculation written by George C. Sih and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 289 pages. Available in PDF, EPUB and Kindle. Book excerpt: Concrete has traditionally been known as a material used widely in the construction of roads, bridges and buildings. Since cost effectiveness has always been one of the more important aspects of design, concrete, when reinforced and/or prestressed, is finding more use in other areas of application such as floating marine structures, storage tanks, nuclear vessel containments and a host of other structures. Because of the demand for concrete to operate under different loading and environmen tal conditions, increasing attention has been paid to study concrete specimens and structure behavior. A subject of major concern is how the localized segregation of the constituents in concrete would affect its global behavior. The degree of nonhomogeneity due to material property and damage. by yielding and/or cracking depends on the size scale and loading rate under consideration. Segregation or clustering of aggregates at the macroscopic level will affect specimen behavior to a larger degree than it would to a large structure such as a dam. Hence, a knowledge of concrete behavior over a wide range of scale is desired. The parameters governing micro-and macro-cracking and the techniques for evaluating and observing the damage in concrete need to be better understood. This volume is intended to be an attempt in this direction. The application of Linear Elastic Fracture Mechanics to concrete is discussed in several of the chapters.
Download or read book Fatigue and Fracture written by F. C. Campbell and published by ASM International. This book was released on 2012-01-01 with total page 699 pages. Available in PDF, EPUB and Kindle. Book excerpt: "This book emphasizes the physical and practical aspects of fatigue and fracture. It covers mechanical properties of materials, differences between ductile and brittle fractures, fracture mechanics, the basics of fatigue, structural joints, high temperature failures, wear, environmentally-induced failures, and steps in the failure analysis process."--publishers website.
Download or read book Fracture Fatigue and Structural Integrity of Metallic Materials written by Sergio Cicero and published by . This book was released on 2020 with total page 170 pages. Available in PDF, EPUB and Kindle. Book excerpt: Fracture, fatigue, and other subcritical processes, such as creep crack growth or stress corrosion cracking, present numerous open issues from both scientific and industrial points of view. These phenomena are of special interest in industrial and civil metallic structures, such as pipes, vessels, machinery, aircrafts, ship hulls, and bridges, given that their failure may imply catastrophic consequences for human life, the natural environment, and/or the economy. Moreover, an adequate management of their operational life, defining suitable inspection periods, repairs, or replacements, requires their safety or unsafety conditions to be defined. The analysis of these technological challenges requires accurate comprehensive assessment tools based on solid theoretical foundations as well as structural integrity assessment standards or procedures incorporating such tools into industrial practice.
Download or read book Mechanical and Corrosion Properties written by and published by . This book was released on 1981 with total page 240 pages. Available in PDF, EPUB and Kindle. Book excerpt: 1979- published in three parts: Nonferrous metals and alloys. Nonmetals. Ferrous metals and alloys.
Download or read book Mechanical Behavior of Materials written by Marc A. Meyers and published by . This book was released on 2008 with total page 856 pages. Available in PDF, EPUB and Kindle. Book excerpt: Includes numerous examples and problems for student practice, this textbook is ideal for courses on the mechanical behaviour of materials taught in departments of mechanical engineering and materials science.
Download or read book Bonding Theory for Metals and Alloys written by Frederick E. Wang and published by Elsevier. This book was released on 2018-11-30 with total page 230 pages. Available in PDF, EPUB and Kindle. Book excerpt: Bonding Theory for Metals and Alloys, 2e builds on the success of the first edition by introducing new experimental data to each chapter that support the breakthrough "Covalon" Conduction Theory developed by Dr. Wang. Through the recognition of the covalent bond in coexistence with the 'free' electron band, the book describes and demonstrates how the many experimental observations on metals and alloys can all be reconciled. Subsequently, it shows how the individual view of metals and alloys by physicists, chemists and metallurgists can be unified. This book covers such phenomena as the Miscibility Gap between two liquid metals, phase equilibrium, superconductivity, superplasticity, liquid metal embrittlement, and corrosion. The author also introduces a new theory based on 'Covalon' conduction, which forms the basis for a new approach to the theory of superconductivity. Bonding Theory for Metals and Alloys, 2e is of interest to physical and theoretical chemists alongside engineers working in research and industry, as well as materials scientists, physicists, and students at the upper undergraduate and graduate level in these fields. All chapters completed revised to reflect developments in research since 2005 New experimental data added to each chapter Broadens experimental data to support the author’s "Covalon" conduction theory, which carries current in covalent bonded pairs Total of approximately 30% - 35% new and revised content
Download or read book Engineering Materials 1 written by M. F. Ashby and published by . This book was released on 1996 with total page 324 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book gives a broad introduction to the properties of materials used in engineering applications, and is intended to provide a course in engineering materials for students with no previous background in the subject.
Download or read book Solidification Processing written by Merton C. Flemings and published by McGraw-Hill Companies. This book was released on 1974 with total page 386 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Structural Materials for Generation IV Nuclear Reactors written by Pascal Yvon and published by Woodhead Publishing. This book was released on 2016-08-27 with total page 686 pages. Available in PDF, EPUB and Kindle. Book excerpt: Operating at a high level of fuel efficiency, safety, proliferation-resistance, sustainability and cost, generation IV nuclear reactors promise enhanced features to an energy resource which is already seen as an outstanding source of reliable base load power. The performance and reliability of materials when subjected to the higher neutron doses and extremely corrosive higher temperature environments that will be found in generation IV nuclear reactors are essential areas of study, as key considerations for the successful development of generation IV reactors are suitable structural materials for both in-core and out-of-core applications. Structural Materials for Generation IV Nuclear Reactors explores the current state-of-the art in these areas. Part One reviews the materials, requirements and challenges in generation IV systems. Part Two presents the core materials with chapters on irradiation resistant austenitic steels, ODS/FM steels and refractory metals amongst others. Part Three looks at out-of-core materials. Structural Materials for Generation IV Nuclear Reactors is an essential reference text for professional scientists, engineers and postgraduate researchers involved in the development of generation IV nuclear reactors. Introduces the higher neutron doses and extremely corrosive higher temperature environments that will be found in generation IV nuclear reactors and implications for structural materials Contains chapters on the key core and out-of-core materials, from steels to advanced micro-laminates Written by an expert in that particular area
Download or read book CRC Handbook of Metal Etchants written by Perrin Walker and published by CRC Press. This book was released on 1990-12-11 with total page 1434 pages. Available in PDF, EPUB and Kindle. Book excerpt: This publication presents cleaning and etching solutions, their applications, and results on inorganic materials. It is a comprehensive collection of etching and cleaning solutions in a single source. Chemical formulas are presented in one of three standard formats - general, electrolytic or ionized gas formats - to insure inclusion of all necessary operational data as shown in references that accompany each numbered formula. The book describes other applications of specific solutions, including their use on other metals or metallic compounds. Physical properties, association of natural and man-made minerals, and materials are shown in relationship to crystal structure, special processing techniques and solid state devices and assemblies fabricated. This publication also presents a number of organic materials which are widely used in handling and general processing...waxes, plastics, and lacquers for example. It is useful to individuals involved in study, development, and processing of metals and metallic compounds. It is invaluable for readers from the college level to industrial R & D and full-scale device fabrication, testing and sales. Scientific disciplines, work areas and individuals with great interest include: chemistry, physics, metallurgy, geology, solid state, ceramic and glass, research libraries, individuals dealing with chemical processing of inorganic materials, societies and schools.
Download or read book Fatigue under Thermal and Mechanical Loading Mechanisms Mechanics and Modelling written by J. Bressers and published by Springer Science & Business Media. This book was released on 2013-04-17 with total page 497 pages. Available in PDF, EPUB and Kindle. Book excerpt: The International Symposium "Fatigue under Thermal and Mechanical Loading", held at Petten (The Netherlands) on May 22-24, 1995, was jointly organized by the Institute for Advanced Materials of The Joint Research Centre, E. C. , and by the Societe Fran~se de Metallurgie et de Materiaux. The fast heating and cooling cycles experienced by many high temperature components cause thermally induced stresses, which often operate in combination with mechanical loads. The resulting thermal / mechanical fatigue cycle leads to material degradation mechanisms and failure modes typical of service cycles. The growing awareness that the synergism between the combined thermal and mechanical loads can not be reproduced by means of isothermal tests, has resulted in an increasing interest in thermal and thermo-mechanical fatigue testing. This trend has been reinforced by the constant pull by industry for more performant, yet safer high temperature systems, pushing the materials to the limit of their properties. Dedicated ASTM meetings in particular have set the scene for this area of research. The proceedings of the symposium organized by D. A. Spera and D. F. Mowbray in 1975 provided a reference book on thermal fatigue which reflects the knowledge and experimental capabilities of the mid-seventies.
Download or read book Physical Foundations of Materials Science written by Günter Gottstein and published by Springer Science & Business Media. This book was released on 2013-03-09 with total page 511 pages. Available in PDF, EPUB and Kindle. Book excerpt: In this vivid and comprehensible introduction to materials science, the author expands the modern concepts of metal physics to formulate basic theory applicable to other engineering materials, such as ceramics and polymers. Written for engineering students and working engineers with little previous knowledge of solid-state physics, this textbook enables the reader to study more specialized and fundamental literature of materials science. Dozens of illustrative photographs, many of them transmission electron microscopy images, plus line drawings, aid developing a firm appreciation of this complex topic. Hard-to-grasp terms such as "textures" are lucidly explained - not only the phenomenon itself, but also its consequences for the material properties. This excellent book makes materials science more transparent.
Download or read book Fracture Mechanics written by Ted L. Anderson and published by CRC Press. This book was released on 2005-06-24 with total page 642 pages. Available in PDF, EPUB and Kindle. Book excerpt: With its combination of practicality, readability, and rigor that is characteristic of any truly authoritative reference and text, Fracture Mechanics: Fundamentals and Applications quickly established itself as the most comprehensive guide to fracture mechanics available. It has been adopted by more than 100 universities and embraced by thousands of professional engineers worldwide. Now in its third edition, the book continues to raise the bar in both scope and coverage. It encompasses theory and applications, linear and nonlinear fracture mechanics, solid mechanics, and materials science with a unified, balanced, and in-depth approach. Reflecting the many advances made in the decade since the previous edition came about, this indispensable Third Edition now includes: A new chapter on environmental cracking Expanded coverage of weight functions New material on toughness test methods New problems at the end of the book New material on the failure assessment diagram (FAD) method Expanded and updated coverage of crack closure and variable-amplitude fatigue Updated solutions manual In addition to these enhancements, Fracture Mechanics: Fundamentals and Applications, Third Edition also includes detailed mathematical derivations in appendices at the end of applicable chapters; recent developments in laboratory testing, application to structures, and computational methods; coverage of micromechanisms of fracture; and more than 400 illustrations. This reference continues to be a necessity on the desk of anyone involved with fracture mechanics.
