Download or read book Statistical Evaluation of Data from Fatigue and Creep rupture Tests Introduction pp 1 written by Waloddi Weibull and published by . This book was released on 1959 with total page 84 pages. Available in PDF, EPUB and Kindle. Book excerpt: General principles of fitting curves to observations are outlined and applied to the methods of maximum likelihood, linear regression, and best linear estimators.

Download or read book Statistical Analysis of Fatigue Data written by Robert Eugene Little and published by ASTM International. This book was released on 1981 with total page 153 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book A Guide for Fatigue Testing and the Statistical Analysis of Fatigue Data written by Committee E-9 Staff and published by . This book was released on 1963-01-01 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book A Guide for Fatigue Testing and the Statistical Analysis of Fatigue Data written by ASTM Committee E-9 on Fatigue and published by . This book was released on 1964 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book A Tentative Guide for Fatigue Testing and the Statistical Analysis of Fatigue Data written by American Society for Testing Materials. Committee E-9 on Fatigue and published by . This book was released on 1958 with total page 100 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Component Assessment Data Requirements from Creep Fatigue Tests written by S. R. Holdsworth and published by . This book was released on 2011 with total page 14 pages. Available in PDF, EPUB and Kindle. Book excerpt: Typically, the lifetime assessment of high temperature components, for which both creep and fatigue are principal damage mechanisms, involves (1) the determination of the stress/strain state at critical locations and (2) a numerical evaluation of the consequential damage condition. Until recently, there has not been a standard procedure specifically covering creep-fatigue testing practices. Creep-fatigue tests had been performed for many years, but the reliability and the form of the information generated was dependent on the expertise and specific interests of individual test laboratories. This situation is now resolved by the publication of a new ASTM standard based on an Electrical Power Research Institute (EPRI) led initiative. The way in which the guidance contained in this new standard specifically aims to provide creep-fatigue data requirements for defect-free component assessment is examined. Cyclic/hold tests, usually involving a simple cycle shape representative of the service transients experienced by the target component, are particularly informative in the provision of data to indicate the concurrent influences of cyclic loading on creep deformation characteristics and creep deformation on cyclic plastic response. The crack initiation endurances of such tests also provide the basis of creep-fatigue damage summation representations for a given material. Sequential creep-fatigue testing can be used to quantify the effects of prior cyclic deformation on creep rupture or prior creep deformation on fatigue endurance. The use of such test methods is also considered.

Download or read book Fatigue Testing and Analysis written by Yung-Li Lee and published by Elsevier. This book was released on 2011-04-18 with total page 417 pages. Available in PDF, EPUB and Kindle. Book excerpt: Fatigue Testing and Analysis: Theory and Practice presents the latest, proven techniques for fatigue data acquisition, data analysis, and test planning and practice. More specifically, it covers the most comprehensive methods to capture the component load, to characterize the scatter of product fatigue resistance and loading, to perform the fatigue damage assessment of a product, and to develop an accelerated life test plan for reliability target demonstration. This book is most useful for test and design engineers in the ground vehicle industry. Fatigue Testing and Analysis introduces the methods to account for variability of loads and statistical fatigue properties that are useful for further probabilistic fatigue analysis. The text incorporates and demonstrates approaches that account for randomness of loading and materials, and covers the applications and demonstrations of both linear and double-linear damage rules. The reader will benefit from summaries of load transducer designs and data acquisition techniques, applications of both linear and non-linear damage rules and methods, and techniques to determine the statistical fatigue properties for the nominal stress-life and the local strain-life methods. - Covers the useful techniques for component load measurement and data acquisition, fatigue properties determination, fatigue analysis, and accelerated life test criteria development, and, most importantly, test plans for reliability demonstrations - Written from a practical point of view, based on the authors' industrial and academic experience in automotive engineering design - Extensive practical examples are used to illustrate the main concepts in all chapters

Download or read book Fatigue 96 written by G. Lütjering and published by Elsevier. This book was released on 1996-05-20 with total page 755 pages. Available in PDF, EPUB and Kindle. Book excerpt: The aim of the 6th International Fatigue Congress, besides covering the entire field of fatigue, was to promote the intimate connection between basic science and engineering application by the selection of appropriate session topics.Fatigue is the main cause of failure of engineering structures and components. Making reliable fatigue predictions is highly difficult because knowledge about fatigue mechanisms in all stages of the fatigue process must be developed much further. In addition, the decreasing availability of raw materials and energy resources forces engineers to continually reduce the weight of constructions. This congress presents research results also particularly for new materials, including composites. Researchers, on the other hand, are confronted with the engineering demands. Futhermore, the overwhelming development which is presently taking place in the field of computer software and hardware dealing with fatigue problems is outlined along with the directions of future developments in all areas of fatigue.Close to 300 fully peer-reviewed papers are published in the proceedings, including nearly 30 overview and keynote papers covering the various session topics. The proceedings should therefore serve as a comprehensive review of the fatigue field at the present state-of-the-art, suitable for scientists, engineers and students.

Download or read book Statistical Research on Fatigue and Fracture written by Tsuneshichi Tanaka and published by Elsevier Science & Technology. This book was released on 1987 with total page 282 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Scientific and Technical Aerospace Reports written by and published by . This book was released on 1995 with total page 376 pages. Available in PDF, EPUB and Kindle. Book excerpt: Lists citations with abstracts for aerospace related reports obtained from world wide sources and announces documents that have recently been entered into the NASA Scientific and Technical Information Database.

Download or read book Proceedings of the Conference on the Design of Experiments written by and published by . This book was released on 1986 with total page 314 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Energy Research Abstracts written by and published by . This book was released on 1993 with total page 754 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Manual on Statistical Planning and Analysis for Fatigue Experiments written by Robert Eugene Little and published by ASTM International. This book was released on 1975 with total page 166 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Publications of the National Institute of Standards and Technology Catalog written by National Institute of Standards and Technology (U.S.) and published by . This book was released on 1979 with total page 696 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book A Guide for Fatigue Testing and the Statistical Analysis of Fatigue Data written by ASTM Committee E-9 on Fatigue and published by . This book was released on 1976 with total page 83 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book NBS Special Publication written by and published by . This book was released on 1968 with total page 452 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Reliability Design of Mechanical Systems written by Seongwoo Woo and published by Springer. This book was released on 2017-01-12 with total page 317 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book describes basic reliability concepts – parametric ALT plan, failure mechanism and design, and reliability testing with acceleration factor and sample size equation. A generalized life-stress failure model with a new effort concept has been derived and recommended to calculate the acceleration factor of the mechanical system. The new sample size equation with the acceleration factor has also been derived to carry out the parametric ALT. This new parametric ALT should help a mechanical/civil engineer to uncover the design parameters affecting reliability during the design process of the mechanical system. Consequently, it should help companies to improve product reliability and avoid recalls due to the product/structure failures in the field. As the improper or missing design parameters in the design phase are experimentally identified by this new reliability design method - parametric ALT, the mechanical/civil engineering system might improve in reliability by the increase in lifetime and the reduction in failure rate.