Download or read book ASTM E466 21 written by American Society for Testing and Materials and published by . This book was released on 2021 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: Descripción del editor: "Significance and Use4.1The axial force fatigue test is used to determine the effect of variations in material, geometry, surface condition, stress, and so forth, on the fatigue resistance of metallic materials subjected to direct stress for relatively large numbers of cycles. The results may also be used as a guide for the selection of metallic materials for service under conditions of repeated direct stress.4.2In order to verify that such basic fatigue data generated using this practice is comparable, reproducible, and correlated among laboratories, it may be advantageous to conduct a round-robin-type test program from a statistician's point of view. To do so would require the control or balance of what are often deemed nuisance variables; for example, hardness, cleanliness, grain size, composition, directionality, surface residual stress, surface finish, and so forth. Thus, when embarking on a program of this nature it is essential to define and maintain consistency a priori, as many variables as reasonably possible, with as much economy as prudent. All material variables, testing information, and procedures used should be reported so that correlation and reproducibility of results may be attempted in a fashion that is considered reasonably good current test practice.4.3The results of the axial force fatigue test are suitable for application to design only when the specimen test conditions realistically simulate service conditions or some methodology of accounting for service conditions is available and clearly defined. 1. Scope1.1This practice covers the procedure for the performance of axial force controlled fatigue tests to obtain the fatigue strength of metallic materials in the fatigue regime where the strains are predominately elastic, both upon initial loading and throughout the test. This practice is limited to the fatigue testing of axial unnotched and notched specimens subjected to a constant amplitude, periodic forcing function in air at room temperature.1.2The use of this test method is limited to specimens and does not cover testing of full-scale components, structures, or consumer products.1.3The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.1.4The text of this standard references notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.Note 1:The following documents, although not directly referenced in the text, are considered important enough to be listed in this practice:E739 Practice for Statistical Analysis of Linear or Linearized Stress-Life (S-N) and Strain-Life (?-N) Fatigue DataSTP 566 Handbook of Fatigue Testing1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee." (Technormen).

Download or read book Standard Practice for Conducting Force Controlled Constant Amplitude Axial Fatigue Tests of Metallic Materials written by American Society for Testing and Materials and published by . This book was released on 2007 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Standard Practice for Conducting Force Controlled Constant Amplitude Axial Fatigue Tests of Metallic Materials written by American Society for Testing and Materials. Committee E08 on Fatigue and Fracture and published by . This book was released on 2002 with total page 10 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book ASTM E466 15 written by American Society for Testing and Materials and published by . This book was released on 2015 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Standard Practice for Conducting Force Controlled Constant Amplitude Axial Fatigue Tests of Metallic Materials written by and published by . This book was released on 2021 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Standard Practice for Conducting Force Controlled Constant Amplitude Axial Fatigue Tests of Metallic Materials1 written by American Society for Testing and Materials and published by . This book was released on 2007 with total page 5 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book E466 96 Standard Practice for Conducting Force Controlled Constant Amplitude Axial Fatigue Tests of Metallic Materials written by and published by . This book was released on with total page pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Standard Practice for Conducting Constant Amplitude Axial Fatigue Tests of Metallic Materials written by and published by . This book was released on 1982 with total page 6 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book ASTM E468 18 written by American Society for Testing and Materials and published by . This book was released on 2018 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: Descripción del editor: "Significance and Use:4.1 Fatigue test results may be significantly influenced by the properties and history of the parent material, the operations performed during the preparation of the fatigue specimens, and the testing machine and test procedures used during the generation of the data. The presentation of fatigue test results should include citation of basic information on the material, specimens, and testing to increase the utility of the results and to reduce to a minimum the possibility of misinterpretation or improper application of those results.Scope:1.1 This practice covers the desirable and minimum information to be communicated between the originator and the user of data derived from constant-force amplitude axial, bending, or torsion fatigue tests of metallic materials tested in air and at room temperature.Note 1: Practice E466, although not directly referenced in the text, is considered important enough to be listed in this standard.1.2 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee." (AENOR).

Download or read book Metallic Materials Constant Amplitude Strain Controlled Axial Fatigue Method of Test written by British Standards Institute Staff and published by . This book was released on 2006-12-29 with total page 28 pages. Available in PDF, EPUB and Kindle. Book excerpt: Metals, Alloys, Fatigue testing, Test specimens, Shape, Dimensions, Testing conditions, Specimen preparation, Test equipment, Verification, Strain measurement

Download or read book Standard Practice for Presentation of Constant Amplitude Fatigue Test Results for Metallic Materials written by American Society for Testing and Materials and published by . This book was released on 1990 with total page 6 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Standard Practice for Verification of Constant Amplitude Dynamic Forces in an Axial Fatigue Testing System written by ASTM International and published by . This book was released on 2009 with total page 11 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Aerospace Series Test Methods for Metallic Materials Constant Amplitude Force Controlled High Cycle Fatigue Testing written by British Standards Institute Staff and published by . This book was released on 2009-11-30 with total page 26 pages. Available in PDF, EPUB and Kindle. Book excerpt: Air transport engineering, Metals, Fatigue testing, Cyclic loading, Mechanical testing, Test specimens, Specimen preparation, Test equipment, Mechanical properties of materials, Alloys

Download or read book Standards Quality Control and Measurement Sciences in 3D Printing and Additive Manufacturing written by Chee Kai Chua and published by Academic Press. This book was released on 2017-06-03 with total page 270 pages. Available in PDF, EPUB and Kindle. Book excerpt: Standards, Quality Control and Measurement Sciences in 3D Printing and Additive Manufacturing addresses the critical elements of the standards and measurement sciences in 3D printing to help readers design and create safe, reliable products of high quality. With 3D printing revolutionizing the process of manufacturing in a wide range of products, the book takes key features into account, such as design and fabrication and the current state and future potentials and opportunities in the field. In addition, the book provides an in-depth analysis on the importance of standards and measurement sciences. With self-test exercises at the end of each chapter, readers can improve their ability to take up challenges and become proficient in a number of topics related to 3D printing, including software usage, materials specification and benchmarking. Helps the reader understand the quality framework tailored for 3D printing processes Explains data format and process control in 3D printing Provides an overview of different materials and characterization methods Covers benchmarking and metrology for 3D printing

Download or read book Fatigue and Tribological Properties of Plastics and Elastomers written by Laurence W. McKeen and published by Butterworth-Heinemann. This book was released on 2009-11-17 with total page 316 pages. Available in PDF, EPUB and Kindle. Book excerpt: Part of a series of core databooks within the William Andrew Plastics Design Library, Fatigue and Tribological Properties of Plastics and Elastomers provides a comprehensive collection of graphical multipoint data and tabular data covering fatigue and tribology. The concept of fatigue is very straightforward: if an object is subjected to a stress or deformation, and it is repeated, the object becomes weaker. This weakening of plastic material is called fatigue. Tribology is the science and technology of surfaces in contact with each other and therefore covers friction, lubrication and wear. The reduction of wear and fatigue and the improvement of lubrication are key bottom-line issues for engineers and scientists involved in the plastics industry and product design with plastics. Fatigue and Tribological Properties of Plastics and Elastomers, Second Edition is an update of all that has changed in the world of plastics since the 1st edition appeared nearly 15 years ago, and has been reorganized from a polymer chemistry point of view. A hard-working reference tool: part of the daily workflow of engineers and scientists involved in the plastics industry and product design with plastics The reduction of wear and fatigue and the improvement of lubrication are key bottom-line issues The data in this book provide engineers with the tools they need to design for low failure rates

Download or read book Standard Practice for Presentation of Constant Amplitude Fatigue Test Results for Metallic Materials written by and published by . This book was released on 2011 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book EN 3987 written by and published by . This book was released on 2009 with total page 22 pages. Available in PDF, EPUB and Kindle. Book excerpt: