EBookClubs

Read Books & Download eBooks Full Online

EBookClubs

Read Books & Download eBooks Full Online

Book Index to DMIC Reports and Memoranda

Download or read book Index to DMIC Reports and Memoranda written by Battelle Memorial Institute. Defense Metals Information Center and published by . This book was released on 1968 with total page 38 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Book U S Government Metalworking Processes and Equipment Program

Download or read book U S Government Metalworking Processes and Equipment Program written by F. C. Holden and published by . This book was released on 1964 with total page 102 pages. Available in PDF, EPUB and Kindle. Book excerpt: A summary is given of the status of the various contracts involved in the U.S. Government's Metalworking Processes and Equipment Program. (Author).

Book Reactor Materials

Download or read book Reactor Materials written by and published by . This book was released on 1968 with total page 316 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Book Reactor Core Materials

Download or read book Reactor Core Materials written by and published by . This book was released on 1968 with total page 612 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Book Summary of Contractor Results in Support of the Refractory Metals Sheet Rolling Program

Download or read book Summary of Contractor Results in Support of the Refractory Metals Sheet Rolling Program written by D. J. Maykuth and published by . This book was released on 1966 with total page 108 pages. Available in PDF, EPUB and Kindle. Book excerpt: This report summarizes the achievements on fourteen programs that were conducted in support of the Metals Sheet Rolling Program. These included programs for developing practices to produce large sheets from two grades of unalloyed tungsten (via powder metallurgy and arc melting, respectively), as well as for the Mo-0.5Ti, Mo-0.5Ti-0.1Zr-0.03C (TZM), Cb-10W-1Zr-0.1C (D-43), Cb-10W-2.5Zr (Cb-752), and Ta-30Cb-7.5V alloys. In addition, pilot sheet-rolling programs were also carried out for the Cb-27Ta-10W-1Zr (FS-85), Cb-5Mo-5V-1Zr (B-66), Ta-7W-3Re (GE-473), and Ta-9.6W-2.4Hf-0.01C (T-222) compositions.

Book A Primer on Soviet Superalloys

Download or read book A Primer on Soviet Superalloys written by J. Prock (Jr.) and published by . This book was released on 1966 with total page 64 pages. Available in PDF, EPUB and Kindle. Book excerpt: Soviet nickel-base and cobalt-base alloys for high-temperature operation are described. Wrought and cast turbine blading alloys are included, as well as oxidation-resistant sheet alloys. Mechanical and physical properties of each alloy are assembled, and a detailed list of references is presented. Where possible, the specific applications are noted. It was concluded that the Soviets have made significant contributions to superalloy development, having successfully circumvented a shortage of cobalt and molybdenum. (Author).

Book Chromium and Chromium Alloys

Download or read book Chromium and Chromium Alloys written by D. J. Maykuth and published by . This book was released on 1966 with total page 130 pages. Available in PDF, EPUB and Kindle. Book excerpt: Various alloying additions have been discovered which render unalloyed chromium much less susceptible to low-temperature embrittlement as well as to nitridation in air at elevated temperatures. These include additions of the Group IIIA metals, magnesia, and carbides based on the Groups IVA and VA metals. Of these additions, only the carbides contribute significantly to the hot strengthening of chromium. The combination of selected carbides and solid-solution-strengthening elements such as tungsten, molybdenum, and/or tantalum, has resulted in experimental alloys which retain useful strengths at temperatures through 1316 C (2400 F). These high strengths are achieved at some sacrifice in the low-temperature ductility of chromium. Also, despite the improvements afforded in the oxidation and nitridation resistance of chromium through alloying, no alloys are available which are capable of service in long-time exposures in air above 982 C (1800 F) without suffering some property degradation.

Book Stress corrosion Cracking and Hydrogen stress Cracking of High strength Steel

Download or read book Stress corrosion Cracking and Hydrogen stress Cracking of High strength Steel written by Ellis E. Fletcher and published by . This book was released on 1966 with total page 28 pages. Available in PDF, EPUB and Kindle. Book excerpt: High-strength steels are susceptible to delayed cracking under suitable conditions. Frequently such a brittle failure occurs at a stress that is only a fraction of the nominal yield strength. Considerable controversy exists over whether such failures result from two separate and distinct phenomena or whether there is but one mechanism called by two different names. Stress-corrosion cracking is the process in which a crack propagates, at least partially, by the stress induced corrosion of a susceptible metal at the advancing tip of the stress-corrosion crack. There is considerable evidence that this cracking results from the electrtrochemical corrosion of a metal subjected to tensile stresses, either residual or externally applied. Hydrogen-stress cracking is cracking which occurs as the result of hydrogen in the metal lattice in combination with tensile stresses. Hydrogen-stress cracking cannot occur if hydrogen is prevented from entering the steel, or if hydrogen that has entered during processing or service is removed before permanent damage has occurred. It is generally agreed that corrosion plays no part in the actual fracture mechanism. This report was prepared to point out wherein the two fracture mechanisms under consideration are similar and wherein they differ. From the evidence available today, the present authors have concluded that there are two distinct mechansims of delayed failure. (Author).

Book Metal Deformation Processing

Download or read book Metal Deformation Processing written by F. W. Boulger and published by . This book was released on 1964 with total page 182 pages. Available in PDF, EPUB and Kindle. Book excerpt: As part of the Metalworking Process and Equipment Program, a survey was conducted to collect and summarize information on deformation characteristics of metals and their effect on processing operations. This report presents information obtained from reports on Governmentsponsored work and from articles in technical publications. The report covers eight subjects: extrusion, forging, rolling, thermal mechanical variables affecting the properties of refractory metals and alloys, development of preferred orientations, anisotropy of strength and ductility, high-strain-rate deformation, and strain aging. In order to be useful to engineering students and production engineers the topics are treated in two ways. Generalized discussions of common processes point out why specific variables must be modified in order to deform certain types of metals satisfactorily. When practical, data on the more-difficultto-form metals are used to illustrate the principles, limitations, and effects of the processes. The objective is to help the non-specialist recognize the implications of specific findings and to apply them to specific operations. (Author).