Download or read book Seismic Deisgn of Punching Shear Reinforcement in Flat Plates written by ACI Committee 421 and published by . This book was released on 2007-01-01 with total page 22 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Punching shear of structural concrete slabs written by FIB - Féd. Int. du Béton and published by FIB - Féd. Int. du Béton. This book was released on 2017 with total page 396 pages. Available in PDF, EPUB and Kindle. Book excerpt: fib Bulletin 81 reports the latest information available to researchers and practitioners on the analysis, design and experimental evidence of punching shear of structural concrete slabs. It follows previous efforts by the International Federation for Structural Concrete (fib) and its predecessor the Euro-International Committee for Concrete (CEB), through CEB Bulletin 168, Punching Shear in Reinforced Concrete (1985) and fibBulletin 12, Punching of structural concrete slabs (2001), and an international symposium sponsored by the punching shear subcommittee of ACI Committee 445 (Shear and Torsion) and held in Kansas City, Mo., USA, in 2005. This bulletin contains 18 papers that were presented in three sessions as part of an international symposium held in Philadelphia, Pa., USA, on October 25, 2016. The symposium was co-organized by the punching shear sub-committee of ACI 445 and by fib Working Party 2.2.3 (Punching and Shear in Slabs) with the objectives of not only disseminating information on this important design subject but also promoting harmonization among the various design theories and treatment of key aspects of punching shear design. The papers are organized in the same order they were presented in the symposium. The symposium honored Professor Emeritus Neil M. Hawkins (University of Illinois at Urbana-Champaign, USA), whose contributions through the years in the field of punching shear of structural concrete slabs have been paramount. The papers cover key aspects related to punching shear of structural concrete slabs under different loading conditions, the study of size effect on punching capacity of slabs, the effect of slab reinforcement ratio on the response and failure mode of slabs, without and with shear reinforcement, and its implications for the design and formulation in codes of practice, an examination of different analytical tools to predict the punching shear response of slabs, the study of the post-punching response of concrete slabs, the evaluation of design provisions in modern codes based on recent experimental evidence and new punching shear theories, and an overview of the combined efforts undertaken jointly by ACI 445 and fib WP 2.2.3 to generate test result databanks for the evaluation and calibration of punching shear design recommendations in North American and international codes of practice.
Download or read book PRC 421 2 21 Seismic Design of Punching Shear Reinforcement in Flat Plates Guide written by ACI Committee 421 and published by . This book was released on 2021-08 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Shear and Punching Shear in RC and FRC Elements written by fib Fédération internationale du béton and published by fib Fédération internationale du béton. This book was released on 2010-12-01 with total page 274 pages. Available in PDF, EPUB and Kindle. Book excerpt: fib Bulletin 57 is a collection of contributions from a workshop on "Recent developments on shear and punching shear in RC and FRC elements", held in Salò, Italy, in October 2010. Shear is one of a few areas of research into fundamentals of the behaviour of concrete structures where contention remains amongst researchers. There is a continuing debate between researchers from a structures perspective and those from a materials or fracture mechanics perspective about the mechanisms that enable the force flow through a concrete member and across cracks. In 2009, a Working Group was formed within fib Task Group 4.2 "Ultimate Limit State Models" to harmonise different ideas about design procedures for shear and punching. An important outcome of this work was the ensuing discussions between experts and practitioners regarding the shear and punching provisions of the draft fib Model Code, which led to the organization of the Salò workshop. Invited experts in the field of shear and FRC gave 18 lectures at the workshop that was attended by 72 participants from 12 countries in 3 different continents. The contributions from this conference as compiled in this bulletin are believed to represent the best of the current state of knowledge. They certainly are of general interest to fib members and especially helpful in the finalization of the 2010 fibModel Code. It is hoped that this publication will stimulate further research in the field, to refine and harmonize the available analytical models and tools for shear and punching design.
Download or read book The Seismic Design Handbook written by Farzad Naeim and published by Springer Science & Business Media. This book was released on 1989-08-31 with total page 476 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book ACI 318 19 Building Code Requirements for Structural Concrete ACI 318 19 and Commentary ACI 318R 19 written by ACI Committee 318 and published by . This book was released on 2019-05 with total page 624 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Punching Shear in Reinforced Concrete Slabs written by Maria Anna Polak and published by . This book was released on 2005 with total page 320 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Circular Storage Tanks and Silos Third Edition written by Amin Ghali and published by CRC Press. This book was released on 2014-05-12 with total page 392 pages. Available in PDF, EPUB and Kindle. Book excerpt: A Design Aid for Structural Engineers Circular Storage Tanks and Silos, Third Edition effectively explains and demonstrates the concepts needed in the analysis and design of circular tanks. Tanks have to sustain high-quality serviceability over a long lifespan. This text covers computing the stresses in service in several chapters. It considers thermal stresses and the time-dependent stresses produced by creep and shrinkage of concrete and relaxation of prestressed steel. It also examines the effects of cracking and the means for its control. This text is universally applicable; no specific system of units is used in most solved examples. However, it is advantageous to use actual dimensions and forces on the structure in a small number of examples. These problems are set in SI units and Imperial units; the answers and the graphs related to these examples are given in the two systems. What’s New in This Edition: Presents a new chapter on recommended practice for design and construction of concrete water tanks and liquefied natural gas tanks Includes a companion Website providing computer programs CTW and SOR Provides material on CTW (Cylindrical Tank Walls); with simple input, it performs analysis for load combinations anticipated in the design of cylindrical walls with or without prestressing Contains the finite-element computer program SOR (Shells of Revolution); it performs analysis for design of axisymmetrical shells of general shapes This guide is an authoritative resource for the analysis and design of circular storage tanks and silos.
Download or read book Guide to the design and construction of reinforced concrete flat slabs written by and published by . This book was released on 2007-01-01 with total page 101 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Seismic Design Assessment and Retrofitting of Concrete Buildings written by Michael N. Fardis and published by Springer Science & Business Media. This book was released on 2009-07-25 with total page 757 pages. Available in PDF, EPUB and Kindle. Book excerpt: Reflecting the historic first European seismic code, this professional book focuses on seismic design, assessment and retrofitting of concrete buildings, with thorough reference to, and application of, EN-Eurocode 8. Following the publication of EN-Eurocode 8 in 2004-05, 30 countries are now introducing this European standard for seismic design, for application in parallel with existing national standards (till March 2010) and exclusively after that. Eurocode 8 is also expected to influence standards in countries outside Europe, or at the least, to be applied there for important facilities. Owing to the increasing awareness of the threat posed by existing buildings substandard and deficient buildings and the lack of national or international standards for assessment and retrofitting, its impact in that field is expected to be major. Written by the lead person in the development of the EN-Eurocode 8, the present handbook explains the principles and rationale of seismic design according to modern codes and provides thorough guidance for the conceptual seismic design of concrete buildings and their foundations. It examines the experimental behaviour of concrete members under cyclic loading and modelling for design and analysis purposes; it develops the essentials of linear or nonlinear seismic analysis for the purposes of design, assessment and retrofitting (especially using Eurocode 8); and gives detailed guidance for modelling concrete buildings at the member and at the system level. Moreover, readers gain access to overviews of provisions of Eurocode 8, plus an understanding for them on the basis of the simple models of the element behaviour presented in the book. Also examined are the modern trends in performance- and displacement-based seismic assessment of existing buildings, comparing the relevant provisions of Eurocode 8 with those of new US prestandards, and details of the most common and popular seismic retrofitting techniques for concrete buildings and guidance for retrofitting strategies at the system level. Comprehensive walk-through examples of detailed design elucidate the application of Eurocode 8 to common situations in practical design. Examples and case studies of seismic assessment and retrofitting of a few real buildings are also presented. From the reviews: "This is a massive book that has no equal in the published literature, as far as the reviewer knows. It is dense and comprehensive and leaves nothing to chance. It is certainly taxing on the reader and the potential user, but without it, use of Eurocode 8 will be that much more difficult. In short, this is a must-read book for researchers and practitioners in Europe, and of use to readers outside of Europe too. This book will remain an indispensable backup to Eurocode 8 and its existing Designers’ Guide to EN 1998-1 and EN 1998-5 (published in 2005), for many years to come. Congratulations to the author for a very well planned scope and contents, and for a flawless execution of the plan". AMR S. ELNASHAI "The book is an impressive source of information to understand the response of reinforced concrete buildings under seismic loads with the ultimate goal of presenting and explaining the state of the art of seismic design. Underlying the contents of the book is the in-depth knowledge of the author in this field and in particular his extremely important contribution to the development of the European Design Standard EN 1998 - Eurocode 8: Design of structures for earthquake resistance. However, although Eurocode 8 is at the core of the book, many comparisons are made to other design practices, namely from the US and from Japan, thus enriching the contents and interest of the book". EDUARDO C. CARVALHO
Download or read book Reinforced Concrete Flat Plates Under Lateral Loading written by Austin P. Pan and published by . This book was released on 1988 with total page 292 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Construction Management written by Daniel W. Halpin and published by John Wiley & Sons. This book was released on 2017-08-07 with total page 418 pages. Available in PDF, EPUB and Kindle. Book excerpt: It’s often said that the construction professional has to be a “jack of all trades, and master of all.” This text covers a wide range of subjects, reflecting the breadth of knowledge needed to understand the dynamics of this large and complex industry. This edition includes updated chapters on planning and scheduling, a new chapter addressing linear scheduling methods, material regarding the historical background of construction as a profession, and includes an Instructor Resource of solutions to the end-of-chapter review exercises. This text has become a standard course text at many universities. The first four editions have enjoyed wide success as an introductory treatment of the subjects which are critical to success in the construction industry. This fifth edition preserves the features that have been most appreciated by its users throughout the years, and adds suggestions provided by instructors and students through formal surveys and informal feedback to the authors.
Download or read book ICCS21 written by Antonio J.M. Ferreira and published by Società Editrice Esculapio. This book was released on 2018-07-23 with total page 160 pages. Available in PDF, EPUB and Kindle. Book excerpt: It is well-known that the topic of composite mate- rials affects many engineering fields, such as civil, mechanical, aerospace, automotive and chemical. In the last decades, in fact, a huge number of scientific papers concerning these peculiar constituents has been published. Analogously, the industrial progress has been extremely noticeable. The study of composite materials, in general, is a challenging activity since the advancements both in the academia and in the industry provide continually new sparks to develop innovative ideas and applications. The communication, the sharing and the exchange of views can surely help the works of many researchers. This aspect represents the main purpose of this Conference, which aims to collect high-level contributions on the development and the application of composite materials. The establishment of this 21st edition of International Conference on Composite Structures has appeared appropriate to continue what has been begun during the previous editions. ICCS wants to be an occasion for many researchers from each part of the globe to meet and discuss about the recent advancements regarding the use of composite structures, sandwich panels, nanotechnology, bio-composites, delamination and fracture, experimental methods, manufacturing and other countless topics that have filled many sessions during this conference. As a proof of this event, which has taken place in Bologna (Italy), selected plenary and key-note lectures have been collected in the present book.
Download or read book Seismic Design of Reinforced Concrete Buildings written by Jack Moehle and published by McGraw Hill Professional. This book was released on 2014-10-06 with total page 783 pages. Available in PDF, EPUB and Kindle. Book excerpt: Complete coverage of earthquake-resistant concrete building design Written by a renowned seismic engineering expert, this authoritative resource discusses the theory and practice for the design and evaluation of earthquakeresisting reinforced concrete buildings. The book addresses the behavior of reinforced concrete materials, components, and systems subjected to routine and extreme loads, with an emphasis on response to earthquake loading. Design methods, both at a basic level as required by current building codes and at an advanced level needed for special problems such as seismic performance assessment, are described. Data and models useful for analyzing reinforced concrete structures as well as numerous illustrations, tables, and equations are included in this detailed reference. Seismic Design of Reinforced Concrete Buildings covers: Seismic design and performance verification Steel reinforcement Concrete Confined concrete Axially loaded members Moment and axial force Shear in beams, columns, and walls Development and anchorage Beam-column connections Slab-column and slab-wall connections Seismic design overview Special moment frames Special structural walls Gravity framing Diaphragms and collectors Foundations
Download or read book Natural and Synthetic Fiber Reinforced Composites written by Sanjay Mavinkere Rangappa and published by John Wiley & Sons. This book was released on 2022-04-18 with total page 372 pages. Available in PDF, EPUB and Kindle. Book excerpt: Natural and Synthetic Fiber Reinforced Composites Discover a comprehensive exploration of fiber reinforced polymers by an expert team of editors Fiber reinforced polymer (FRP) composites offer several unique properties that make them ideal for use in a wide range of industries, from automotive and aerospace to marine, construction, and co-industrial. In Natural and Synthetic Fiber Reinforced Composites: Synthesis, Properties and Applications, a distinguished team of mechanical engineers delivers a comprehensive overview of fiber reinforced composites. This edited volume includes thorough discussions of glass-, cotton-, and carbon-fiber reinforced materials, as well as the tribological properties and non-structural applications of synthetic fiber composites. Readers will also find practical explorations of the structural evolution, mechanical features, and future possibilities of fiber, textile, and nano-cementitious materials. The physical and chemical properties of cotton fiber-based composites are explored at length, as are the extraordinary mechanical, thermal, electrical, electronic, and field emission properties of carbon nanotubes. This singular book also includes: A thorough discussion of recent advancements in natural fiber reinforced polymer composites, their implications, and the opportunities that arise as a result A comprehensive exploration of the thermal behavior of natural fiber-based composites An insightful review of the literature on sisal fiber with polymer matrices A response to the growing research gap in the existing literature regarding natural fiber-based polymer composites and solutions to address it Perfect for scientists, engineers, professors, and students working in areas involving natural and synthetic reinforced polymers and composites, Natural and Synthetic Fiber Reinforced Composites: Synthesis, Properties and Applications offers a one-of-a-kind resource to help readers understand a critical and rapidly evolving technology.
Download or read book Recent Advances in Structural Engineering and Construction Management written by Kong Kian Hau and published by Springer Nature. This book was released on 2022-09-27 with total page 977 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book presents the select proceedings of the International Conference on Structures, Materials and Construction (ICSMC 2021). It covers the recent developments and futuristic trends in the field of structural engineering and construction management, including new building materials and understanding their behavior. The topic covered also assess the current progress and state-of-the-art techniques in structural experimentation, smart materials, structures technology, principles of construction management, materials properties and characterization. The collection of papers included in this proceeding will contribute to scientific developments in the field of structural engineering and construction and will be a useful as reference material for the academicians, researchers and most importantly the student community pursuing research in the fields of structural engineering and construction technology.
Download or read book High Tech Concrete Where Technology and Engineering Meet written by D.A. Hordijk and published by Springer. This book was released on 2017-06-08 with total page 2926 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book contains the proceedings of the fib Symposium “High Tech Concrete: Where Technology and Engineering Meet”, that was held in Maastricht, The Netherlands, in June 2017. This annual symposium was organised by the Dutch Concrete Association and the Belgian Concrete Association. Topics addressed include: materials technology, modelling, testing and design, special loadings, safety, reliability and codes, existing concrete structures, durability and life time, sustainability, innovative building concepts, challenging projects and historic concrete, amongst others. The fib (International Federation for Structural Concrete) is a not-for-profit association committed to advancing the technical, economic, aesthetic and environmental performance of concrete structures worldwide.
