Download or read book Residual Stress Based Fatigue Design of Welded Structures written by Jonas Hensel and published by . This book was released on 2018 with total page 13 pages. Available in PDF, EPUB and Kindle. Book excerpt: Fatigue design concepts for welded structures generally consider residual stresses as a factor affecting the mean stress influence. Residual stresses are mostly interpreted as mean stresses. In addition, high tensile residual stresses are conservatively assumed, resulting in maximum effective load stresses from fatigue loading in the order of the yield strength. The consequence of this is that additional static load stresses may have no influence on the resulting fatigue strength because the local effective mean stress (residual stresses and load mean stresses) is always high. The related evaluation concepts neither distinguish between different steel grades nor between different origins and amounts of possible residual stresses in welded joints. The real magnitude of existing residual stresses is also usually not considered, because in practice, usually no explicit knowledge of the residual stresses at critical sites of a construction is available because residual stress measurements are not state of the art in welding practice. For an explicit consideration of residual stresses in design concepts, the sign, the initial amount, and especially the amount of the residual stresses after a load induced relaxation must be considered. Therefore, the steel grade and the condition of the material are of great importance, as well as the local stress condition influenced by welding-induced notch geometry. The article shall give an overview about the state of the art of consideration of residual stresses in fatigue design concepts for welded structures and the background of their development. Finally, a new approach shall offer a possibility for an enhanced consideration of residual stresses in design concepts based on the explicit knowledge about the effective residual stresses that can actually be observed with different measurement concepts.

Download or read book Fatigue Strength of Welded Structures written by S J Maddox and published by Woodhead Publishing. This book was released on 2014-03-14 with total page 211 pages. Available in PDF, EPUB and Kindle. Book excerpt: The key to avoidance of fatigue, which is the main cause of service failures, is good design. In the case of welded joints, which are particularly susceptible to fatigue, design rules are available. However, their effective use requires a good understanding of fatigue and an appreciation of problems concerned with their practical application. Fatigue strength of welded structures has incorporates up-to-date design rules with high academic standards whilst still achieving a practical approach to the subject. The book presents design recommendations which are based largely on those contained in recent British standards and explains how they are applied in practice. Attention is also focused on the relevant aspects of fatigue in welded joints which are not yet incorporated in codes thus providing a comprehensive aid for engineers concerned with the design or assessment of welded components or structures. Background information is given on the fatigue lives of welded joints which will enable the engineer or student to appreciate why there is such a contrast between welded and unwelded parts, why some welded joints perform better than others and how joints can be selected to optimise fatigue performance.

Download or read book Fracture and Fatigue of Welded Joints and Structures written by K Macdonald and published by Elsevier. This book was released on 2011-04-19 with total page 353 pages. Available in PDF, EPUB and Kindle. Book excerpt: The failure of any welded joint is at best inconvenient and at worst can lead to catastrophic accidents. Fracture and fatigue of welded joints and structures analyses the processes and causes of fracture and fatigue, focusing on how the failure of welded joints and structures can be predicted and minimised in the design process.Part one concentrates on analysing fracture of welded joints and structures, with chapters on constraint-based fracture mechanics for predicting joint failure, fracture assessment methods and the use of fracture mechanics in the fatigue analysis of welded joints. In part two, the emphasis shifts to fatigue, and chapters focus on a variety of aspects of fatigue analysis including assessment of local stresses in welded joints, fatigue design rules for welded structures, k-nodes for offshore structures and modelling residual stresses in predicting the service life of structures.With its distinguished editor and international team of contributors, Fracture and fatigue of welded joints and structures is an essential reference for mechanical, structural and welding engineers, as well as those in the academic sector with a research interest in the field. - Analyses the processes and causes of fracture and fatigue, focusing predicting and minimising the failure of welded joints in the design process - Assesses the fracture of welded joints and structure featuring constraint-based fracture mechanics for predicting joint failure - Explores specific considerations in fatigue analysis including the assessment of local stresses in welded joints and fatigue design rules for welded structures

Download or read book Fatigue Life Analyses of Welded Structures written by Tom Lassen and published by John Wiley & Sons. This book was released on 2013-03-01 with total page 442 pages. Available in PDF, EPUB and Kindle. Book excerpt: Avoiding or controlling fatigue damage is a major issue in the design and inspection of welded structures subjected to dynamic loading. Life predictions are usually used for safe life analysis, i.e. for verifying that it is very unlikely that fatigue damage will occur during the target service life of a structure. Damage tolerance analysis is used for predicting the behavior of a fatigue crack and for planning of in-service scheduled inspections. It should be a high probability that any cracks appearing are detected and repaired before they become critical. In both safe life analysis and the damage tolerance analysis there may be large uncertainties involved that have to be treated in a logical and consistent manner by stochastic modeling. This book focuses on fatigue life predictions and damage tolerance analysis of welded joints and is divided into three parts. The first part outlines the common practice used for safe life and damage tolerance analysis with reference to rules and regulations. The second part emphasises stochastic modeling and decision-making under uncertainty, while the final part is devoted to recent advances within fatigue research on welded joints. Industrial examples that are included are mainly dealing with offshore steel structures. Spreadsheets which accompany the book give the reader the possibility for hands-on experience of fatigue life predictions, crack growth analysis and inspection planning. As such, these different areas will be of use to engineers and researchers.

Download or read book Analysis of Welded Structures written by Koichi Masubuchi and published by Elsevier. This book was released on 2013-10-22 with total page 655 pages. Available in PDF, EPUB and Kindle. Book excerpt: Analysis of Welded Structures: Residual Stresses, Distortion, and their Consequences encompasses several topics related to design and fabrication of welded structures, particularly residual stresses and distortion, as well as their consequences. This book first introduces the subject by presenting the advantages and disadvantages of welded structures, as well as the historical overview of the topic and predicted trends. Then, this text considers residual stresses, heat flow, distortion, fracture toughness, and brittle and fatigue fractures of weldments. This selection concludes by discussing the effects of distortion and residual stresses on buckling strength of welded structures and effects of weld defects on service behavior. This book also provides supplementary discussions on some related and selected subjects. This text will be invaluable to metallurgists, welders, and students of metallurgy and welding.

Download or read book Recommendations for Fatigue Design of Welded Joints and Components written by A. F. Hobbacher and published by Springer. This book was released on 2015-12-23 with total page 153 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book provides a basis for the design and analysis of welded components that are subjected to fluctuating forces, to avoid failure by fatigue. It is also a valuable resource for those on boards or commissions who are establishing fatigue design codes. For maximum benefit, readers should already have a working knowledge of the basics of fatigue and fracture mechanics. The purpose of designing a structure taking into consideration the limit state for fatigue damage is to ensure that the performance is satisfactory during the design life and that the survival probability is acceptable. The latter is achieved by the use of appropriate partial safety factors. This document has been prepared as the result of an initiative by Commissions XIII and XV of the International Institute of Welding (IIW).

Download or read book Fatigue of Welded Structures written by Timothy Russell Gurney and published by CUP Archive. This book was released on 1979-12-20 with total page 480 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Design and Analysis of Fatigue Resistant Welded Structures written by Dieter Radaj and published by Woodhead Publishing. This book was released on 1990-01-03 with total page 386 pages. Available in PDF, EPUB and Kindle. Book excerpt: An English version of a sucessful German book. Both traditional and modern concepts are described.

Download or read book Fatigue Testing of Weldments written by D. W. Hoeppner and published by ASTM International. This book was released on 1978 with total page 304 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Fatigue Design of Welded Joints and Components written by A Hobbacher and published by Woodhead Publishing. This book was released on 1996-10-31 with total page 132 pages. Available in PDF, EPUB and Kindle. Book excerpt: These recommendations present general methods for the assessment of fatigue damage in welded components, which may affect the limit states of a structure, such as ultimate limit state and serviceability limited state. Fatigue resistance data is given for welded components made of wrought or extruded products of ferritic/pearlitic or banitic structural steels up to fy = 700 Mpa and of aluminium alloys commonly used for welded structures.

Download or read book Stress Determination for Fatigue Analysis of Welded Components written by E. Niemi and published by Woodhead Publishing. This book was released on 1995-04-30 with total page 80 pages. Available in PDF, EPUB and Kindle. Book excerpt: This report introduces definitions of the terminology relevant to stress determination for fatigue analysis of welded components. The various stress concentrations, stress categories and fatigue analysis methods are defined. Fatigue analysis methods considered are nominal stress, hot spot stress, notch stress, notch strain and fracture mechanics approaches. The report also contains comprehensive recommendations concerning the application of finite element methods and experimental methods for stress determination. It is intended for fatigue design of common welded structures, such as cranes, excavators, vehicle frames, bridges, ship hulls, offshore structures etc. fabricated from materials at least 3mm thick. In general, attention is focused on weld details which give rise to fatigue cracking from the surface, notably from the weld toe.

Download or read book Fatigue Analysis of Welded Components written by E. Niemi and published by Woodhead Publishing. This book was released on 2006-09-27 with total page 56 pages. Available in PDF, EPUB and Kindle. Book excerpt: This report provides background and guidance on the use of the structural hot spot stress approach to the fatigue design of welded components and structures. It complements the IIW recommendations for 'Fatigue Design of Welded Joints and Components' and extends the information provided in the IIW recommendations on 'Stress Determination for Fatigue Analysis of Welded Components'. This approach is applicable to cases of potential fatigue cracking from the weld toe. It has been in use for many years in the context of tubular joints. The present report concentrates on its extension to structures fabricated from plates and non-tubular sections.Following an explanation of the structural hot spot stress, its definition and its relevance to fatigue, the authors describe methods for its determination. Stress determination from both finite element analysis and strain gauge measurements is considered. Parametric formulae for calculating stress increases due to misalignment and structural discontinuities are also presented. Special attention is paid to the use of finite element stress analysis and guidance is given on the choice of element type and size for use with either solid or shell elements. Design S-N curves for use with the structural hot spot stress are presented for a range of weld details. Finally, practical application of the recommendations is illustrated in two case studies involving the fatigue assessment of welded structures using the structural hot spot stress approach. - Provides practical guidance on the application of the structural hot-spot stress approach - Discusses stress determination from both finite element analysis and strain gauge measurements - Practical application of the recommendations is illustrated in two case studies

Download or read book Residual Stress Analysis on Welded Joints by Means of Numerical Simulation and Experiments written by Paolo Ferro and published by BoD – Books on Demand. This book was released on 2018-05-16 with total page 164 pages. Available in PDF, EPUB and Kindle. Book excerpt: The ability to quantify residual stresses induced by welding processes through experimentation or numerical simulation has become, today more than ever, of strategic importance in the context of their application to advanced design. This is an ongoing challenge that commenced many years ago. Recent design criteria endeavour to quantify the effect of residual stresses on fatigue strength of welded joints to allow a more efficient use of materials and a greater reliability of welded structures. The aim of the present book is contributing to these aspects of design through a collection of case-studies that illustrate both standard and advanced experimental and numerical methodologies used to assess the residual stress field in welded joints. The work is intended to be of assistance to designers, industrial engineers and academics who want to deepen their knowledge of this challenging topic.

Download or read book Fatigue Design of Marine Structures written by Inge Lotsberg and published by Cambridge University Press. This book was released on 2016-04-13 with total page 559 pages. Available in PDF, EPUB and Kindle. Book excerpt: Fatigue Design of Marine Structures provides students and professionals with a theoretical and practical background for fatigue design of marine structures including sailing ships, offshore structures for oil and gas production, and other welded structures subject to dynamic loading such as wind turbine structures. Industry expert Inge Lotsberg brings more than forty years of experience in design and standards-setting to this comprehensive guide to the basics of fatigue design of welded structures. Topics covered include laboratory testing, S-N data, different materials, different environments, stress concentrations, residual stresses, acceptance criteria, non-destructive testing, improvement methods, probability of failure, bolted connections, grouted connections, and fracture mechanics. Featuring twenty chapters, three hundred diagrams, forty-seven example calculations, and resources for further study, Fatigue Design of Marine Structures is intended as the complete reference work for study and practice.

Download or read book Fatigue Assessment of Welded Joints by Local Approaches written by Dieter Radaj and published by Woodhead Publishing. This book was released on 2006-10-30 with total page 661 pages. Available in PDF, EPUB and Kindle. Book excerpt: Local approaches to fatigue assessment are used to predict the structural durability of welded joints, to optimise their design and to evaluate unforeseen joint failures. This standard work provides a systematic survey of the principles and practical applications of the various methods. It covers the hot spot structural stress approach to fatigue in general, the notch stress and notch strain approach to crack initiation and the fracture mechanics approach to crack propagation. Seam-welded and spot-welded joints in structural steels and aluminium alloys are also considered.This completely reworked second edition takes into account the tremendous progress in understanding and applying local approaches which has been achieved in the last decade. It is a standard reference for designers, structural analysts and testing engineers who are responsible for the fatigue-resistant in-service behaviour of welded structures. - Completely reworked second edition of a standard work providing a systematic survey of the principles and practical applications of the various methods - Covers the hot spot structural stress approach to fatigue in general, the notch stress and notch strain approach to crack initiation and the fracture mechanics approach to crack propagation. - Written by a distinguished team of authors

Download or read book Model Analysis of Fatigue Life Estimation of Welded Structures microform written by Muhammad A. Wahab and published by National Library of Canada. This book was released on 1984 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This study includes both an experimental and theoretical analysis of the effect of residual stresses on the fatigue life of butt-welded low-alloy steel structures. The purpose is to develop a more complete method to estimate the total fatigue life of a weldment. To theoretically calculate the total fatigue life the process was considered as a combination of crack initiation and crack propagation lives. The initiation portion was based on an extension of the local-strain fatigue life initiation model to accomodate the effect of residual and mean stresses. To determine the local notch-root stress-strain condition more accurately a relationship between the fatigue notch and stress concentration factors was developed. Using elastic superposition and modifying Neuber's equation, which relates nominal stress-strain to local notch-root stress-strain residual stresses at the weld-toe were simulated. This analysis allows a more complete estimation of crack initiation life. For the theoretical analysis of fatigue crack propagation life Forman's equation with an appropriate combination effective stress ratio, axial and bending stresses along with residual stress effects was considered. To incorporate the residual stress distribution at the weld-toe a theoretical expression which correlates closely with experimentally determined distributions was developed. Unlike previous investigations this analysis allows the study of the combined effects of axial loading, bending stresses and residual stresses on the fatigue crack propagation life to be considered. With this theoretical model the total fatigue life can be predicted using basic material properties and the loading history including any surface treatment. To test the suitability of this analysis it was applied to welds with mechanically and thermally induced surface stresses. The residual stresses due to various treatments (annealing, tensile preloading, glass and steel shot peening, single and multiple point hammer peening and stress peening) were used to theoretically predict the total fatigue life. The more complete theoretical analysis of the total fatigue life was compared to the experimental results for all the treated and untreated welded specimens. The results show very good agreement; the variations in applied stress for a given fatigue life were between four to 15% for all the treatments listed above.

Download or read book Fatigue and Fracture of Weldments written by Uwe Zerbst and published by Springer. This book was released on 2018-12-11 with total page 174 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book provides a comprehensive and thorough guide to those readers who are lost in the often-confusing context of weld fatigue. It presents straightforward information on the fracture mechanics and material background of weld fatigue, starting with fatigue crack initiation and short cracks, before moving on to long cracks, crack closure, crack growth and threshold, residual stress, stress concentration, the stress intensity factor, J-integral, multiple cracks, weld geometries and defects, microstructural parameters including HAZ, and cyclic stress-strain behavior. The book treats all of these essential and mutually interacting parameters using a unique form of analysis.