Download or read book Additively Manufactured Inconel 718 written by Dunyong Deng and published by Linköping University Electronic Press. This book was released on 2018-01-24 with total page 82 pages. Available in PDF, EPUB and Kindle. Book excerpt: Additive manufacturing (AM), also known as 3D printing, has gained significant interest in aerospace, energy, automotive and medical industries due to its capabilities of manufacturing components that are either prohibitively costly or impossible to manufacture by conventional processes. Among the various additive manufacturing processes for metallic components, electron beam melting (EBM) and selective laser melting (SLM) are two of the most widely used powder bed based processes, and have shown great potential for manufacturing high-end critical components, such as turbine blades and customized medical implants. The futures of the EBM and SLM are doubtlessly promising, but to fully realize their potentials there are still many challenges to overcome. Inconel 718 (IN718) is a nickel-base superalloy and has impressive combination of good mechanical properties and low cost. Though IN718 is being mostly used as a turbine disk material now, the initial introduction of IN718 was to overcome the poor weldability of superalloys in 1960s, since sluggish precipitation of strengthening phases ?’/?’’ enables good resistance to strain-age cracking during welding or post weld heat treatment. Given the similarity between AM and welding processes, IN718 has been widely applied to the metallic AM field to facilitate the understandings of process-microstructure-property relationships. The work presented in this licentiate thesis aims to better understand microstructures and mechanical properties EBM and SLM IN718, which have not been systematically investigated. Microstructures of EBM and SLM IN718 have been characterized with scanning electron microscopy (SEM), transmission electron microscopy (TEM) and correlated with the process conditions. Monotonic mechanical properties (e.g., Vickers microhardness and tensile properties) have also been measured and rationalized with regards to the microstructure evolutions before and after heat treatments. For EBM IN718, the results show the microstructure is not homogeneous but dependant on the location in the components, and the anisotropic mechanical properties are probably attributed to alignment of porosities rather than texture. Post heat treatment can slightly increase the mechanical strength compared to the as-manufactured condition but does not alter the anisotropy. SLM IN718 shows significantly different microstructure and mechanical properties to EBM IN718. The as-manufactured SLM IN718 has very fine dendritic microstructure and Laves phases in the interdendrites, and is “work-hardened” by the residual strains and dislocations present in the material. Mechanical properties are different between horizontally and vertically built samples, and heat treatment can minimize this difference. Results from this licentiate thesis provide the basis for the further research on the cyclic mechanical properties of EBM and SLM IN718, which would be the focus of following phase of the Ph.D. research.
Download or read book Welding Metallurgy and Weldability of Nickel Base Alloys written by John C. Lippold and published by John Wiley & Sons. This book was released on 2011-09-20 with total page 370 pages. Available in PDF, EPUB and Kindle. Book excerpt: The most up-to-date coverage of welding metallurgy aspects and weldability issues associated with Ni-base alloys Welding Metallurgy and Weldability of Nickel-Base Alloys describes the fundamental metallurgical principles that control the microstructure and properties of welded Ni-base alloys. It serves as a practical how-to guide that enables engineers to select the proper alloys, filler metals, heat treatments, and welding conditions to ensure that failures are avoided during fabrication and service. Chapter coverage includes: Alloying additions, phase diagrams, and phase stability Solid-solution strengthened Ni-base alloys Precipitation strengthened Ni-base alloys Oxide dispersion strengthened alloys and nickel aluminides Repair welding of Ni-base alloys Dissimilar welding Weldability testing High-chromium alloys used in nuclear power applications With its excellent balance between the fundamentals and practical problem solving, the book serves as an ideal reference for scientists, engineers, and technicians, as well as a textbook for undergraduate and graduate courses in welding metallurgy.
Download or read book Superalloys written by Matthew J. Donachie and published by ASM International. This book was released on 2002 with total page 439 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book covers virtually all technical aspects related to the selection, processing, use, and analysis of superalloys. The text of this new second edition has been completely revised and expanded with many new figures and tables added. In developing this new edition, the focus has been on providing comprehensive and practical coverage of superalloys technology. Some highlights include the most complete and up-to-date presentation available on alloy melting. Coverage of alloy selection provides many tips and guidelines that the reader can use in identifying an appropriate alloy for a specific application. The relation of properties and microstructure is covered in more detail than in previous books.
Download or read book Nickel Cobalt and Their Alloys written by Joseph R. Davis and published by ASM International. This book was released on 2000-01-01 with total page 450 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book is a comprehensive guide to the compositions, properties, processing, performance, and applications of nickel, cobalt, and their alloys. It includes all of the essential information contained in the ASM Handbook series, as well as new or updated coverage in many areas in the nickel, cobalt, and related industries.
Download or read book Additive Manufacturing written by T.S. Srivatsan and published by CRC Press. This book was released on 2015-09-25 with total page 448 pages. Available in PDF, EPUB and Kindle. Book excerpt: Get Ready for the Future of Additive ManufacturingAdditive Manufacturing: Innovations, Advances, and Applications explores the emerging field of additive manufacturing (AM)-the use of 3D printing to make prototype parts on demand. Often referred to as the third industrial revolution, AM offers many advantages over traditional manufacturing. This pr
Download or read book TMS 2018 147th Annual Meeting Exhibition Supplemental Proceedings written by The Minerals, Metals & Materials Society and published by Springer. This book was released on 2018-02-03 with total page 898 pages. Available in PDF, EPUB and Kindle. Book excerpt: This collection features papers presented at the 147th Annual Meeting & Exhibition of The Minerals, Metals & Materials Society.
Download or read book Superalloys written by Elihu F. Bradley and published by ASM International(OH). This book was released on 1988 with total page 296 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Selective Laser Melting Materials and Applications written by Prashanth Konda Gokuldoss and published by . This book was released on 2020 with total page 98 pages. Available in PDF, EPUB and Kindle. Book excerpt: Additive manufacturing (AM) is one of the manufacturing processes that warrants the attention of industrialists, researchers, and scientists. AM has the ability to fabricate materials to produce parts with complex shapes without any theoretical restrictions combined with added functionalities. Selective laser melting (SLM), also known as laser-based powder bed processing (LPBF), is one of the main AM process that can be used to fabricate wide variety of materials that are Al-, Ti-, Fe-, Ni-, Co-, W-, Ag-, and Au-based, etc. However, several challenges need to be addressed systematically, such as development of new materials that suit the SLM process conditions so the process capabilities can be fully used to produce new properties in these materials. Other issues in the field are the lack of microstructure-property correlations, premature failure, etc. Accordingly, this Special Issue (book) focuses mainly on the microstructure-correlation in three different alloys: AlSi10Mg, Ti6Al4V, and 304L stainless steel, where six articles are presented. Hence, this Special Issue outlines microstructure-property correlations in the SLM processed materials and provides a value addition to the field of AM.
Download or read book Hot Working Guide written by Y. V. R. K. Prasad and published by ASM International. This book was released on 1997-01-01 with total page 566 pages. Available in PDF, EPUB and Kindle. Book excerpt: A unique source book with flow stress data for hot working, processing maps with metallurgical interpretation and optimum processing conditions for metals, alloys, intermetallics, and metal matrix composites. The use of this book replaces the expensive and time consuming trial and error methods in process design and product development.
Download or read book The Cost of Corrosion in China written by Baorong Hou and published by Springer Nature. This book was released on 2019-09-26 with total page 953 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book comprehensively covers corrosion and corrosion protection in China in the areas including infrastructure, transportation, energy, water environment, as well as manufacturing and public utilities. Furthermore, it presents a major consulting project of Chinese Academy of Engineering, which was the largest corrosion investigation project in Chinese history, including the corresponding methods, processes and corrosion protection strategies, and provides valuable information for numerous industries. Sharing essential insights into corrosion prediction and decision-making, this book will help to decrease costs and extend the service life of equipment and facilities; accordingly, it will benefit scientists and engineers working on corrosion research and protection, as well as economists and government employees.
Download or read book Additive Manufacturing Volume 2 written by Prashanth Konda Gokuldoss and published by MDPI. This book was released on 2020-04-15 with total page 351 pages. Available in PDF, EPUB and Kindle. Book excerpt: Additive manufacturing (AM) is one of the manufacturing processes that warrants the attention of industrialists, researchers and scientists, because of its ability to produce materials with a complex shape without theoretical restrictions and with added functionalities. There are several advantages to employing additive manufacturing as the primary additive manufacturing process. However, there exist several challenges that need to be addressed systematically. A couple such issues are alloy design and process development. Traditionally alloys designed for conventional cast/powder metallurgical processes were fabricated using advanced AM processes. This is the wrong approach considering that the alloys should be coined based on the process characteristics and meta-stable nature of the process. Hence, we must focus on alloy design and development for AM that suits the AM processes. The AM processes, however, improve almost every day, either in terms of processing capabilities or processing conditions. Hence, the processing part warrants a section that is devoted to these advancements and innovations. Accordingly, the present Special Issue (book) focuses on two aspects of alloy development and process innovations. Here, 45 articles are presented covering different AM processes including selective laser melting, electron beam melting, laser cladding, direct metal laser sintering, ultrasonic consolidation, wire arc additive manufacturing, and hybrid manufacturing. I believe that this Special Issue bears is vital to the field of AM and will be a valuable addition.
Download or read book Heat Treater s Guide written by Harry Chandler and published by ASM International. This book was released on 1996-01-01 with total page 690 pages. Available in PDF, EPUB and Kindle. Book excerpt: The material is contained in more than 500 datasheet articles, each devoted exclusively to one particular alloy, a proven format first used in the complementary guide for irons and steels. For even more convenience, the datasheets are arranged by alloy groups: nickel, aluminum, copper, magnesium, titanium, zinc and superalloys. The book provides very worthwhile and practical information in such areas as: compositions, trade names, common names, specifications (both U.S. and foreign), available products forms, typical applications, and properties (mechanical, fabricating, and selected others). This comprehensive resource also covers the more uncommon alloys by groups in the same datasheet format. Included are: refractory metals and alloys (molybdenum, tungsten, niobium, tantalum), beryllium copper alloys, cast and P/M titanium parts, P/M aluminum parts, lead and lead alloys, tin-rich alloys, and sintering copper-base materials (copper-tin, bronze, brass, nickel silvers).
Download or read book Superalloys 2012 written by Eric S. Huron and published by John Wiley & Sons. This book was released on 2012-10-02 with total page 952 pages. Available in PDF, EPUB and Kindle. Book excerpt: A superalloy, or high-performance alloy, is an alloy that exhibits excellent mechanical strength at high temperatures. Superalloy development has been driven primarily by the aerospace and power industries. This compilation of papers from the Twelfth International Symposium on Superalloys, held from September 9-13, 2012, offers the most recent technical information on this class of materials.
Download or read book Aerospace Materials Handbook written by Sam Zhang and published by CRC Press. This book was released on 2016-04-19 with total page 763 pages. Available in PDF, EPUB and Kindle. Book excerpt: Whether an airplane or a space shuttle, a flying machine requires advanced materials to provide a strong, lightweight body and a powerful engine that functions at high temperature. The Aerospace Materials Handbook examines these materials, covering traditional superalloys as well as more recently developed light alloys. Capturing state-of-the-art d
Download or read book Welding Metallurgy written by Sindo Kou and published by John Wiley & Sons. This book was released on 2003-03-31 with total page 477 pages. Available in PDF, EPUB and Kindle. Book excerpt: Updated to include new technological advancements in welding Uses illustrations and diagrams to explain metallurgical phenomena Features exercises and examples An Instructor's Manual presenting detailed solutions to all the problems in the book is available from the Wiley editorial department.
Download or read book Mechanical Behavior of Materials written by William F. Hosford and published by Cambridge University Press. This book was released on 2010 with total page 437 pages. Available in PDF, EPUB and Kindle. Book excerpt: This is a textbook on the mechanical behavior of materials for mechanical and materials engineering. It emphasizes quantitative problem solving. This new edition includes treatment of the effects of texture on properties and microstructure in Chapter 7, a new chapter (12) on discontinuous and inhomogeneous deformation, and treatment of foams in Chapter 21.
Download or read book Laser Additive Manufacturing of High Performance Materials written by Dongdong Gu and published by Springer. This book was released on 2015-04-21 with total page 322 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book entitled “Laser Additive Manufacturing of High-Performance Materials” covers the specific aspects of laser additive manufacturing of high-performance new materials components based on an unconventional materials incremental manufacturing philosophy, in terms of materials design and preparation, process control and optimization and theories of physical and chemical metallurgy. This book describes the capabilities and characteristics of the development of new metallic materials components by laser additive manufacturing process, including nanostructured materials, in situ composite materials, particle reinforced metal matrix composites, etc. The topics presented in this book, similar as laser additive manufacturing technology itself, show a significant interdisciplinary feature, integrating laser technology, materials science, metallurgical engineering and mechanical engineering. This is a book for researchers, students, practicing engineers and manufacturing industry professionals interested in laser additive manufacturing and laser materials processing. Dongdong Gu is a Professor at College of Materials Science and Technology, Nanjing University of Aeronautics and Astronautics (NUAA), PR China.
