Download or read book Pulsed Film Cooling on a Turbine Blade Leading Edge written by James L. Rutledge and published by . This book was released on 2009 with total page 500 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Three dimensional Numerical Simulation of Film Cooling on a Turbine Blade Leading edge Model written by Douglas Stenger and published by . This book was released on 2009 with total page 98 pages. Available in PDF, EPUB and Kindle. Book excerpt: The present study is a three-dimensional numerical investigation of the effectiveness of film cooling for a turbine blade leading-edge model with both a single and a three-hole cooling configuration. The model used has the same dimensions as those in the experimental investigation of Ou and Rivir (2006). It consists of a half cylinder with a flat after-body, and well represents the leading edge of a turbine blade. The single coolant hole is situated approximately at the spanwise center of the cylindrical model, and makes an angle of 21.5 degrees to the leading edge and 20 degrees to the spanwise direction. For the three-hole configuration, the center hole is positioned the same as the single hole in the single-hole configuration, with the adjacent holes located at a spanwise distance of 37.4 mm on either side of the center hole. Multi-block grids were generated using GridGen, and the flows were simulated using the flow solver Fluent. A highly clustered structured C-grid was developed around the leading edge of the model. The outer unstructured-grid domain represents the wind tunnel as used in the experimental study of Ou and Rivir (2006), and the leading-edge model is located at the center of the domain. Simulations were carried out for blowing ratios, M, ranging from 0.75 to 2.0. Turbulence was represented using the k-? shear-stress transport (SST) model, and the flow was assumed to have a free-stream turbulence intensity of 0.75%. Two types of boundary conditions were used to represent the blade wall: an adiabatic surface, and a conductive surface. The adiabatic-wall results over-predicted the film-cooling effectiveness in the far downstream region for low blowing ratios. Also, in the vicinity of the cooling hole, an increase in blowing ratio resulted in higher film cooling effectiveness than observed in the experiments. It should be noted that the steady RANS-based turbulence model used under-predicts the interaction between the coolant and mainstream flow near the cooling-pipe exit. The conductive-wall results show a much closer agreement with experimental data for film effectiveness as compared to the adiabatic-wall predictions. Simulations were also performed with higher values of turbulence intensity at the cooling-hole inlet, and these predicted the coolant-mainstream interaction and the film-cooling effectiveness more accurately. Finally, a novel concept of pulsing the coolant flow was implemented so as to achieve film-cooling effectiveness equivalent to that with constant cooling, but with reduced overall coolant air, thereby enhancing turbine efficiency. Pulsed cooling with pulsing frequency PF = 5 and 10Hz, and duty cycle DC = 50%, shows the greatest cooling effects. The three-hole cooling results indicate that the 49 mm spanwise distance used for computing the spanwise-averaged values for film-cooling effectiveness accounts for all of the film-coolant spreading provided by the single hole. Also, the neighboring cooling holes contribute little film cooling to the 49 mm spanwise distance. The most significant new finding in this work is that the inclusion of wall conductance is the main factor responsible for reproducing the experimental data.

Download or read book Single hole Film Cooling on a Turbine blade Leading edge Model written by and published by . This book was released on 2008 with total page 78 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Survey of Advantages and Problems Associated with Transpiration Cooling and Film Cooling of Gas turbine Blades written by Ernst Rudolf Georg Eckert and published by . This book was released on 1951 with total page 44 pages. Available in PDF, EPUB and Kindle. Book excerpt: Summary: Transpiration and film cooling promise to be effective methods of cooling gas-turbine blades; consequently, analytical and experimental investigations are being conducted to obtain a better understanding of these processes. This report serves as an introduction to these cooling methods, explains the physical processes, and surveys the information available for predicting blade temperatures and heat-transfer rates. In addition, the difficulties encountered in obtaining a uniform blade temperature are discussed, and the possibilities of correcting these difficulties are indicated. Air is the only coolant considered in the application of these cooling methods.

Download or read book Leading Edge Film Cooling Effects on Turbine Blade Heat Transfer written by Vijay K. Garg and published by . This book was released on 1995 with total page 26 pages. Available in PDF, EPUB and Kindle. Book excerpt: Presented at the International Gas Turbine and Aeroengine Congress and Exposition, Houston, Texas - June 5-8, 1995.

Download or read book Effects of Pulsing on Film Cooling of Gas Turbine Airfoils written by Sarah Marie Coulthard and published by . This book was released on 2005 with total page 70 pages. Available in PDF, EPUB and Kindle. Book excerpt: The objective of this project was to determine the effects of pulsed film cooling on turbine blades. High combustor temperatures, resulting in elevated turbine inlet temperatures, produce high engine efficiency. At current operating temperatures, the turbine inlet temperature is above the melting point of the turbine blades. Thus cooling the blades in the first stages after the combustor is essential. Current methods for film cooling utilize a continuous stream of bleed air from the compressor. This air is routed into a cavity inside each blade and bled out of holes onto the blade surface, creating a film of cool air. Pulsed film cooling may reduce the amount of bleed air used, thus increasing the efficiency of the engine by allowing more air to flow through the combustor, while providing equivalent protection for the blades. In this study, a section of a turbine blade was modeled using a plate with a row of five film cooling holes. Coolant air was pulsed via solenoid valves from a plenum, while a wind tunnel provided a mainstream flow. Temperature and velocity fields were measured over the blade surface with varying blowing rates of the coolant and frequencies of pulsing. The film cooling effectiveness, a measure of how well the coolant protects the blade surface, was calculated based on the measured temperatures. The results were compared to baseline cases with continuous blowing and no blowing. The overall best case was continuous film cooling with the jet velocity one fourth of the mainstream velocity. However, results showed that pulsed film cooling has the potential to provide an equivalent or greater film cooling effectiveness for higher jet velocities. The case of pulsed jets with a jet velocity equal to the mainstream velocity, pulsing frequency of 20 Hertz, and 75% duty cycle showed an increased film cooling effectiveness and decreased heat transfer compared to the continuous blowing case. This study suggests that pulsed film cooling has the potential to adequately protect gas turbine blades with additional research, ultimately allowing for an increased efficiency in a gas turbine engine.

Download or read book Computations of Film Cooling for the Leading Edge Region of a Turbine Blade Model written by Pingfan He and published by . This book was released on 1995 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: Presented at the International Gas Turbine and Aeroengine Congress and Exposition, Houston, Texas - June 5-8, 1995.

Download or read book High mainstream turbulence effects on film cooling of a turbine blade leading edge written by Christopher Ashleigh Johnston and published by . This book was released on 1999 with total page 180 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Computational Simulation and Analysis of Film Cooling for the Leading edge Model of a Turbine Blade written by and published by . This book was released on 2007 with total page 147 pages. Available in PDF, EPUB and Kindle. Book excerpt: The application of interest is the cooling of turbine blades in large gas combustion engines where hot gases from the combustor cause thermal deterioration of the metal turbine blades. A thin-film of coolant flow buffers the hottest parts of the blade surface. Heat transfer on a bluff body and, subsequently, a single-hole cooling problem is solved numerically in two-dimensions. The flow is assumed to be incompressible, and the laminar, steady Navier-Stokes equations are used to obtain the flow solution. Results for the bluff-body heat transfer agree very well with experimental data up to the separation point, and are within 20% of the data thereafter. The film-cooling simulation yielded higher cooling effectiveness due in large part to the use of the two-dimensional model, which treats the hole as a slot with higher coolant mass. Results from the simulations indicate that the Cobalt flow solver is capable of solving complex heat transfer problems.

Download or read book Numerical Simulation of a Film Cooled Turbine Blade Leading Edge Including Heat Transfer Effects written by Laurene D. Dobrowolski and published by . This book was released on 2009 with total page 436 pages. Available in PDF, EPUB and Kindle. Book excerpt: Computations and experiments were run to study heat transfer and overall effectiveness for a simulated turbine blade leading edge. Computational predictions were run for a film cooled leading edge model using a conjugate numerical method to predict the normalized "metal" temperatures for the model. This computational study was done in conjunction with a parallel effort to experimentally determine normalized metal temperatures, i.e. overall effectiveness, using a specially designed high conductivity model. Predictions of overall effectiveness were higher than experimentally measured values in the stagnation region, but lower along the downstream section of the leading edge. Reasons for the differences between computational predictions and experimental measurements were examined. Also of interest was the validity of Taw as the driving temperature for heat transfer into the blade, and this was examined via computations. Overall, this assumption gave reasonable results except near the stagnation line. Experiments were also conducted on a leading edge with no film cooling to gain a better understanding of the additional cooling provided by film cooling. Heat flux was also measured and external and internal heat transfer coefficients were determined. The results showed roughly constant overall effectiveness on the external surface.

Download or read book Investigations of Flow and Film Cooling on Turbine Blade Edge Regions written by Huitao Yang and published by . This book was released on 2006 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: The inlet temperature of modern gas turbine engines has been increased to achieve higher thermal efficiency and increased output. The blade edge regions, including the blade tip, the leading edge, and the platform, are exposed to the most extreme heat loads, and therefore, must be adequately cooled to maintain safety. For the blade tip, there is tip leakage flow due to the pressure gradient across the tip. This leakage flow not only reduces the blade aerodynamic performance, but also yields a high heat load due to the thin boundary layer and high speed. Various tip configurations, such as plane tip, double side squealer tip, and single suction side squealer tip, have been studied to find which one is the best configuration to reduce the tip leakage flow and the heat load. In addition to the flow and heat transfer on the blade tip, film cooling with various arrangements, including camber line, upstream, and two row configurations, have been studied. Besides these cases of low inlet/outlet pressure ratio, low temperature, non-rotating, the high inlet/outlet pressure ratio, high temperature, and rotating cases have been investigated, since they are closer to real turbine working conditions. The leading edge of the rotor blade experiences high heat transfer because of the stagnation flow. Film cooling on the rotor leading edge in a 11/2 turbine stage has been numerically studied for the designand off-design conditions. Simulations find that the increasing rotating speed shifts the stagnation line from the pressure side, to the leading edge and the suction side, while film cooling protection moves in the reverse direction with decreasing cooling effectiveness. Film cooling brings a high unsteady intensity of the heat transfer coefficient, especially on the suction side. The unsteady intensity of film cooling effectiveness is higher than that of the heat transfer coefficient. The film cooling on the rotor platform has gained significant attention due to the usage of low-aspect ratio and low-solidity turbine designs. Film cooling and its heat transfer are strongly influenced by the secondary flow of the end-wall and the stator-rotor interaction. Numerical predictions have been performed for the film cooling on the rotating platform of a whole turbine stage. The design conditions yield a high cooling effectiveness and decrease the cooling effectiveness unsteady intensity, while the high rpm condition dramatically reduces the film cooling effectiveness. High purge flow rates provide a better cooling protection. In addition, the impact of the turbine work process on film cooling effectiveness and heat transfer coefficient has been investigated. The overall cooling effectiveness shows a higher value than the adiabatic effectiveness does.

Download or read book Effects of Leading Edge Film Cooling and Surface Roughness on the Downstream Film Cooling Along a Transonic Turbine Blade for Low and High Free Stream Turbulence written by and published by . This book was released on 2008 with total page 63 pages. Available in PDF, EPUB and Kindle. Book excerpt: This report is the culmination of a two year effort to demonstrate the capability for performing near wall high resolution Time Resolved Particle Image Velocimetry (TRDPIV) measurements in a transonic turbine. Performing TRDPIV in high speed wall bounded flows with high resolution/magnification often posses significant difficulties. For this reason, two preliminary studies where conducted in order to further understand the challenges that would be present in this type of environment. Hardware and algorithm advancements and developments ultimately enabled performing TRDPIV in the transonic cascade facility. However, high pressure, high speed and the turbine blade complex geometries (high curvature and acceleration) significantly inhibit our ability to deliver homogeneous distribution of flow tracers, especially in the near wall region resulting in low quality measurements and regions with randomly missing data. In addition to our experimental results this effort delivers a novel advanced data reconstruction methodology based on proper orthogonal decomposition that was developed to overcome the aforementioned limitation. The following report documents in detail the methods and results generated throughout this effort.

Download or read book Velocity and Temperature Profiles in Leading edge Film Cooling of Gas Turbine Blades written by Andrew T. Anderson and published by . This book was released on 1985 with total page 93 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Unsteady High Turbulence Effects on Turbine Blade Film Cooling Heat Transfer Performance Using a Transient Liquid Crystal Technique written by National Aeronautics and Space Administration (NASA) and published by Createspace Independent Publishing Platform. This book was released on 2018-06-27 with total page 228 pages. Available in PDF, EPUB and Kindle. Book excerpt: Unsteady wake effect, with and without trailing edge ejection, on detailed heat transfer coefficient and film cooling effectiveness distributions is presented for a downstream film-cooled gas turbine blade. Tests were performed on a five-blade linear cascade at an exit Reynolds number of 5.3 x 10(exp 5). Upstream unsteady wakes were simulated using a spoke-wheel type wake generator. Coolant blowing ratio was varied from 0.4 to 1.2; air and CO2 were used as coolants to simulate different density ratios. Surface heat transfer and film effectiveness distributions were obtained using a transient liquid crystal technique; coolant temperature profiles were determined with a cold wire technique. Results show that Nusselt numbers for a film cooled blade are much higher compared to a blade without film injection. Unsteady wake slightly enhances Nusselt numbers but significantly reduces film effectiveness versus no wake cases. Nusselt numbers increase only slic,htly but film cooling, effectiveness increases significantly with increasing, blowing ratio. Higher density coolant (CO2) provides higher effectiveness at higher blowing ratios (M = 1.2) whereas lower density coolant (Air) provides higher 0 effectiveness at lower blowing ratios (M = 0.8). Trailing edge ejection generally has more effect on film effectiveness than on the heat transfer, typically reducing film effectiveness and enhancing heat transfer. Similar data is also presented for a film cooled cylindrical leading edge model. Han, J. C. and Ekkad, S. V. and Du, H. and Teng, S. Glenn Research Center NAG3-1656; RTOP 714-01-4A

Download or read book Gas Turbine Blade Cooling written by Chaitanya D Ghodke and published by SAE International. This book was released on 2018-12-10 with total page 238 pages. Available in PDF, EPUB and Kindle. Book excerpt: Gas turbines play an extremely important role in fulfilling a variety of power needs and are mainly used for power generation and propulsion applications. The performance and efficiency of gas turbine engines are to a large extent dependent on turbine rotor inlet temperatures: typically, the hotter the better. In gas turbines, the combustion temperature and the fuel efficiency are limited by the heat transfer properties of the turbine blades. However, in pushing the limits of hot gas temperatures while preventing the melting of blade components in high-pressure turbines, the use of effective cooling technologies is critical. Increasing the turbine inlet temperature also increases heat transferred to the turbine blade, and it is possible that the operating temperature could reach far above permissible metal temperature. In such cases, insufficient cooling of turbine blades results in excessive thermal stress on the blades causing premature blade failure. This may bring hazards to the engine's safe operation. Gas Turbine Blade Cooling, edited by Dr. Chaitanya D. Ghodke, offers 10 handpicked SAE International's technical papers, which identify key aspects of turbine blade cooling and help readers understand how this process can improve the performance of turbine hardware.

Download or read book Systematic Study of Shaped hole Film Cooling at the Leading Edge of a Scaled up Turbine Blade written by Jacob Damian Moore and published by . This book was released on 2020 with total page 484 pages. Available in PDF, EPUB and Kindle. Book excerpt: The leading-edge regions of turbine vanes and blades require careful attention to their cooling designs because of the high heat loads. External cooling is typically accomplished with dense "showerhead" arrangements of film cooling holes surrounding the stagnation point at the airfoil leading edge. In modern film cooling studies, shaped holes are prevalent in downstream areas of turbine airfoils; however, the literature contains few studies of shaped holes in the showerhead. This leads to a lack of physics-based insight that would lead to the design of high-performing showerhead arrays. This study examined the performance and physical behavior of several showerhead arrangements at the leading edge of a scaled-up turbine blade. A low-speed linear cascade test section was used to simulate the blade environment, and experiments were conducted at scaled engine-realistic conditions. First, the cooling performances of baseline cylindrical and shaped hole designs were compared. The shaped hole design mimicked a standard design in the literature for flat plate studies but with some modifications expected to improve performance specifically at the leading edge. The result was a novel off-center, elliptically-expanding hole. Adiabatic effectiveness and thermal field measurements revealed that the baseline shaped hole had 20-100% performance due to better jet attachment, stemming from its diffuser, which effectively decreased the exit momenta of the coolant jets. The expansion area ratio was increased by 40% for a subsequent design to gauge sensitivity to this parameter; but, surprisingly, the performances of the new design and of the baseline one were nearly identical. A third shaped hole design with a 45% larger breakout area but an identical expansion area resulted in slightly worse performance than either, highlighting the detrimental effect of increasing breakout area and expansion angle. These experiments informed a new proposed scaling parameter incorporating both of these areas and their counteracting effects to predict shaped hole performance in the showerhead. The highest performing design of the group was then tested with an engine-realistic impingement coolant feed, for which performance was overall similar. Supplemental thermal fields using this configuration were performed to construct a 3D representation of the flow field in the showerhead region

Download or read book A Simulation of Film Cooling in the Leading Edge Region of a Turbine Blade trench Effect on Film Effectiveness from Cylinder in Crossflow written by and published by . This book was released on 2012 with total page 65 pages. Available in PDF, EPUB and Kindle. Book excerpt: