Download or read book Operator Station Sound Level Measurement Procedure for Earthmoving Machinery work Cycle Test SAE J1166a written by American National Standards Institute and published by . This book was released on 1980 with total page 9 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book OPERATOR STATION SOUND LEVEL MEASUREMENT PROCEDURE FOR EARTHMOVING MACHINERYWORK CYCLE TEST written by OPTC3, Lighting and Sound Committee and published by . This book was released on 1979 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This SAE Recommended Practice sets forth the procedures to be used only in measuring sound levels and the determination of the time weighted sound level at the operator station(s) of earthmoving machinery of 15 kW (20 bhp) and over. Earthmoving machinery is defined per SAE J1057a. This recommended practice is applicable to earthmoving machinery which has operator station(s) where the operator can either stand or sit and is transported by the machinery during operation. The recommended practice describes the instrumentation requirements and specifies work cycles for earthmoving machinery. The recommended practice describes the method used to calculate the time weighted average sound level at the operator station(s) identified in the practice as Leq(5) for continuous operation of the work cycle. A method to relate the time weighted average sound level at the operator station(s) to operator sound exposure is also provided.
Download or read book OPERATOR STATION SOUND LEVEL MEASUREMENT PROCEDURE FOR POWERED MOBILE EARTHMOVING MACHINERYWORK CYCLE TEST written by OPTC3, Lighting and Sound Committee and published by . This book was released on 1976 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This SAE Recommended Practice sets forth the procedures to be used only in measuring sound levels and the determination of the time weighted average sound level at the operator station(s) of powered mobile earthmoving machinery of 15 kW (20 bhp) and over. This Recommended Practice is applicable to earthmoving machinery which has operator station(s) where the operator can either stand or sit and is transported by the machinery during its operation. The Recommended Practice describes the instrumentation requirements and specifies work cycles for earthmoving machinery. The Recommended Practice describes the method used to calculate the time weighted average sound level at the operator station(s)identified in this practice as Leq(5)for continuous operation on the work cycle. A method to relate the time weighted average sound level at the operator station(s) to operator sound exposure is also provided.
Download or read book OPERATOR SOUND LEVEL MEASUREMENT PROCEDURE FOR POWERED MOBILE CONSTRUCTION MACHINERYSINGULAR TYPE TEST written by OPTC3, Lighting and Sound Committee and published by . This book was released on 1976 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This SAE Recommended Practice sets forth the instrumentation and procedures to be used in measuring sound levels at the operator station for powered mobile construction machinery of 15 kW (20 bhp) rated and over. This Recommended Practice is to cover machinery that has operator stations where the operator can either stand or sit and will be transported by the machine during its operation. The sound levels obtained by using the test procedures set forth in this SAE Recommended Practice are in general repeatable and are representative of the higher range of the sound levels generated by the machinery under field operating conditions, but do not necessarily represent the equivalent sound level over a field use cycle.
Download or read book OPERATOR SOUND LEVEL MEASUREMENT PROCEDURE FOR EARTHMOVING MACHINERYSINGULAR TYPE TEST written by OPTC3, Lighting and Sound Committee and published by . This book was released on 1979 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This SAE Standard is applicable to machinery of 15 kw (20 bhp) rated and over, that have operator stations where the operator can either stand or sit and will be transported by the machine during its operation. It is not intended for use with agricultural equipment. The sound levels obtained by using the test procedures set forth in this SAE Standard are in general repeatable, and are representative of the higher range of the sound levels generated by the machinery under field operating conditions, but do not necessarily represent the equivalent sound level over a field use cycle. For measurement and calculation of the operator's sound exposure, use SAE Recommended Practice J1166a.
Download or read book Acoustics Measurement of Noise Emitted By Earthmoving Machinery At the OperatorS Position Simulated Work Cycle Test Conditions written by SLTC - Earth Moving Machinery Sound Level and published by . This book was released on 1991 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This SAE Standard describes a method for determining the noise emitted by earthmoving machinery at the operator's position in terms of the equivalent continuous A-weighted sound pressure level while the machine is carrying out a simulated work cycle. This SAE standard is a special test code for specific types of earthmoving machinery. It is an extension of ISO 6081 which contains the general requirements for many types of machinery and equipment. A simulated rather than an actual work cycle test condition is chosen. Simulated work cycles provide acceptable noise emission data which are repeatable and representative. Actual work cycle tests are complex and repeatability can be a problem. Specific procedures are described in this document to enable the sound pressure level at the operator's position,with the machine in a simulated work cycle test condition, to be determined in a manner which is repeatable. Attachments (bucket, dozer, etc.) for the manufacturer's production version are to be fitted since this is the configuration most likely to exist when the machine is in actual use. This document enables compliance with noise limits to be determined. It can also be used for evaluation purposes in noise reduction investigations. An additional special test code is given in SAE J2104/ISO 6395. This other special test code is intended to be used to determine the noise emitted by earthmovign machinery in terms fo the A-weighted sound power level while the machine is in a simulated work cycle test condition. Corresponding measurements of exterior noise and noise at the operator's position under stationary test conditions are described in SAE J2102/ISO 6393 and ISO J2103/ISO 6394, respectively.
Download or read book Sound Analysis and Noise Control written by John Foreman and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 473 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book has been written to provide an intro Chapter 2 deals with the mechanism of hear duction to the fundamental concepts of sound ing and the subjective rating of sound, includ and a comprehensive coverage whereby un ing age-related and noise-induced hearing loss. wanted sound (noise) can be controlled. Al Assessment of any noise problem involves a though there are many notable textbooks which knowledge of the instrumentation available for deal primarily with the physics (or theory) of measurements, the limitations of this instru sound, and others which treat noise control in mentation, the appropriate procedures for mak a strictly practical (and sometimes even empir ing the measurements with the instrumentation, ical) manner, there are few textbooks that pro and the methods by which the measured data vide a bridging between the necessary under can be analyzed. Chapter 3 provides an up-to standing of the fundamentals of sound (its date coverage of these requirements, including generation, propagation, measurement) and the a section on one of the newest and most valu application of these fundamentals to its control. able tools in noise studies-sound intensity This book provides that link. measurement. The capability of being able to The text presents noise control primarily at measure sound intensity as compared with con the introductory level.
Download or read book Operator Sound Level Measurement Procedure for Earthmoving Machinery singular Type Test SAE J919c written by American National Standards Institute and published by . This book was released on 1980 with total page 3 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book 1983 SAE Handbook written by Society of Automotive Engineers and published by . This book was released on 1983 with total page 476 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Acoustics Measurement of Exterior Noise Emitted By Earthmoving Machinery Dynamic Test Conditions written by SLTC - Earth Moving Machinery Sound Level and published by . This book was released on 1991 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This SAE Standard describes a method for determining the noise emitted to the environment by earthmoving machinery in terms of the A-weighted sound power level while the machine is working under dynamic test conditions. This SAE Standard is special test code for specific types of earthmoving machinery. It is an extension of SAE J2101/ISO 4872, which contains the general requirements for construction equipment. A simulated dynamic rath than an actual work cycle test condition is chosen. Dynamic test conditions provide acceptable noise emission data, which are repeatable and representative. Actual work cycle tests are complex and repeatability can be a problem Specific procedures are described in this document to enable the sound power emission in dynamic test conditions to be determined in a manner that is repeatable. Attachments (bucket, dozer, etc.) for the manufacturer's production version are to be fitted since this is the configuration most likely to exist when the machine is in actual use. This document enables compliance with noise limits to be determined. It can also be used for evaluation purposes in noise reduction investigation. An additional special test code is given in SAE J2105/ISO 6396.2. This other special test code is intended to be used to determine the noise emitted by earthmoving machiner, with the machine in dynamic test conditions, measured at the operator's position in terms of the equivalent continuous A-weighted sound pressure level. Corresponding measurements of noise emitted to the environment and noise at the operator's position under stationary test conditions are described in SAE J2102/ISO 6393 and SAE J2103/ISO 6394, respectively.
Download or read book EXTERIOR SOUND LEVEL MEASUREMENT PROCEDURE FOR EARTHMOVING MACHINERY written by OPTC3, Lighting and Sound Committee and published by . This book was released on 1979 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This SAE Standard is applicable to machinery of 15 kw (20 rated bhp) and over. It is not intended to cover operation of safety devices (such as backup alarms). The sound levels obtained by using the test procedures set forth in this SAE Standard are repeatable and are representative of the higher range of sound levels generated by the machinery under actual field operating conditions, but do not necessarily represent the average sound level over a field use cycle.
Download or read book SOUND LEVEL MEASUREMENT PROCEDURE FOR TRENCHING EQUIPMENT written by SLTC - Earth Moving Machinery Sound Level and published by . This book was released on 1979 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: All types of trenching equipment regardless of engine size may be tested under this recommended practice. It is not intended to cover operation of safety devices such as backup alarms or accessories such as paving breakers. The sound levels obtained by using the test procedures set forth in this SAE Recommended Practice are repeatable and are representative of the higher range of sound levels generated by the machinery under actual field operating conditions, but do not necessarily represent the average sound level over a field use cycle. For measurement and calculation of the operator's sound exposure, the procedure should follow the SAE Recommended Practice J1166a.
Download or read book Operator Sound Level Measurement Procedure for Powered Mobile Construction Machinery singular Type Test SAE J919b written by American National Standards Institute and published by . This book was released on 1978 with total page 3 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Index to Noise Standards written by Marilyn A. Cadoff and published by . This book was released on 1984 with total page 172 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Test Procedure for the Measurement of Sound Emitted from Construction Forestry and Mining Machines to the Operator Station and Exterior of the Machine written by Canadian Standards Association and published by Rexdale, Ont. : The Association. This book was released on 1986 with total page 29 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Sound Measurement Off Road Self Propelled Work Machines Operator Work Cycle written by SLTC - Earth Moving Machinery Sound Level and published by . This book was released on 1998 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This SAE Standard sets forth the procedures to be used in measuring sound levels and determining the time weighted sound level at the operator's station(s) of specified off-road self-propelled work machines. This document applies to the following work machines which have operator stations as specified in SAE J1116: Crawler LoaderWheel LoaderDumperTractor ScraperGraderCrawler Tractor with DozerWheel Tractor with DozerPad Foot Wheel Compactor with DozerBackhoeHydraulic ExcavatorLog SkidderExcavator and Wheel Feller-BuncherPipelayerRoller/CompactorTrencherSweeper The instrumentation requirements and specific work cycles for these machines are described. The method used to calculate the time weighted average sound level at the operator station(s) is specified for Leq(5), or optional exchange rates, during continuous operation in a work cycle. A method to relate the time weighted average sound level at the operator station(s) to operator sound exposure is also provided.
Download or read book Noise Control Engineering Journal written by and published by . This book was released on 2001 with total page 324 pages. Available in PDF, EPUB and Kindle. Book excerpt:
