Download or read book Nucleate Pool Boiling of Surface modified Nano porous Alumina written by Bong June Zhang and published by . This book was released on 2012 with total page 294 pages. Available in PDF, EPUB and Kindle. Book excerpt: In nucleate pool boiling, heat transfer augment is an important issue. Among various techniques for enhancement, porous surfaces with millimeter to micron-sized diameter have been studied in the past few decades. In this study, the nano porous surface (NPS) of alumina was created to address technical issues in submicron regime pool boiling. Especially, influence of surface modifications (structural and chemical treatments) of the NPS over heat transfer enhancement was the subject of the reported research. There are a few important aspects of the research reported in this dissertation: to develop the optimal NPS to increase heat transfer in nucleate pool boiling, to suggest the mechanistic model to explain heat transfer augment in submicron regime, and to assess the feasibility of the NPS for nucleate pool boiling enhancement. First of all, an optimal NPS with surface modifications for heat transfer in nucleate pool boiling was developed. The surface-modified NPS provides enlarged heating surface area, active nucleation site enhancement, and improvement of vapor-liquid menisci through reentrant-shaped cavities. Secondly, the mechanistic model suggested in this study explained that the combination of convection-driven and phase change-induced heat transfers and liquid thin film evaporation (LTFE) achieves heat transfer augment. Especially, the model supported the hypothesis that the NPS is appropriate to dissipate heat through the LTFE at lower heat flux regime. Lastly, this study shows that heat transfer enhancement phenomena of the NPS that was evaluated and quantified by using various physical and electrochemical methods. For instance, most contributing factor of the CHF enhancement was assumed the liquid spreading and the absorption-induced capillary pressure. They were assessed by using Apparent Water Contact Angle (AWCA) and Electrochemical Impedance Spectroscopy (EIS) measurements of which trends were well matched with CHF experimental data.
Download or read book Boiling written by Yasuo Koizumi and published by Elsevier. This book was released on 2017-06-22 with total page 849 pages. Available in PDF, EPUB and Kindle. Book excerpt: Boiling: Research and Advances presents the latest developments and improvements in the technologies, instrumentation, and equipment surrounding boiling. Presented by the Japan Society of Mechanical Engineers, the book takes a holistic approach, first providing principles, and then numerous practical applications that consider size scales. Through six chapters, the book covers contributed sections from knowledgeable specialists on various topics, ranging from outlining boiling phenomena and heat transfer characteristics, to the numerical simulation of liquid-gas two phase flow. It summarizes, in a single volume, the state-of-the-art in boiling heat transfer and provides a valuable resource for thermal engineers and practitioners working in the thermal sciences and thermal engineering. Explores the most recent advancements in boiling research and technology from the last twenty years Provides section content written by contributing experts in their respective research areas Shares research being conducted and advancements being made on boiling and heat transfer in Japan, one of the major research hubs in this field
Download or read book VDI Heat Atlas written by VDI Gesellschaft and published by Springer Science & Business Media. This book was released on 2010-07-21 with total page 1608 pages. Available in PDF, EPUB and Kindle. Book excerpt: For more than 50 years, the Springer VDI Heat Atlas has been an indispensable working means for engineers dealing with questions of heat transfer. Featuring 50% more content, this new edition covers most fields of heat transfer in industrial and engineering applications. It presents the interrelationships between basic scientific methods, experimental techniques, model-based analysis and their transfer to technical applications.
Download or read book Hydrodynamic Aspects of Boiling Heat Transfer written by N. Zuber and published by . This book was released on 1959 with total page 216 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Effects of Surface Parameters on Boiling Heat Transfer Phenomena written by Bao Hoai Truong and published by . This book was released on 2011 with total page 156 pages. Available in PDF, EPUB and Kindle. Book excerpt: Nanofluids, engineered colloidal dispersions of nanoparticles in fluid, have been shown to enhance pool and flow boiling CHF. The CHF enhancement was due to nanoparticle deposited on the heater surface, which was verified in pool boiling. However, no such work has been done for flow boiling. Using a cylindrical tube pre-coated with Alumina nanoparticles coated via boiling induced deposition, CHF of water was found to enhance up to 40% compared to that of the bare tube. This confirms that nanoparticles on the surface is responsible for CHF enhancement for flow boiling. However, existing theories failed to predict the CHF enhancement and the exact surface parameters attributed to the enhancement cannot be determined. Surface modifications to enhance critical heat flux (CHF) and Leidenfrost point (LFP) have been shown successful in previous studies. However, the enhancement mechanisms are not well understood, partly due to many surface parameters being altered at the same time, as in the case for nanofluids. Therefore, the remaining objective of this work is to evaluate separate surface effect on different boiling heat transfer phenomena. In the second part of this study, surface roughness, wettability and nanoporosity were altered one by one and respective effect on quenching LFP with water droplet was determined. Increase in surface roughness and wettability enhanced LFP; however, nanoporosity was most effective in raising LFP, almost up to 100°C. The combination of the micro posts and nanoporous coating layer proved optimal. The nanoporous layer destabilizes the vapor film via heterogeneous bubble nucleation, and the micro posts provides intermittent liquid-surface contacts; both mechanisms increase LFP. In the last part, separate effect of nanoporosity and surface roughness on pool boiling CHF of a well-wetting fluid, FC-72, was investigated. Nanoporosity or surface roughness alone had no effect on pool boiling CHF of FC-72. Data obtained in the literature mostly for microporous coatings showed CHF enhancement for well wetting fluids, and existing CHF models are unable to predict the enhancement.
Download or read book Handbook of Thermal Science and Engineering written by and published by Springer. This book was released on 2018-07-31 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This Handbook provides researchers, faculty, design engineers in industrial R&D, and practicing engineers in the field concise treatments of advanced and more-recently established topics in thermal science and engineering, with an important emphasis on micro- and nanosystems, not covered in earlier references on applied thermal science, heat transfer or relevant aspects of mechanical/chemical engineering. Major sections address new developments in heat transfer, transport phenomena, single- and multiphase flows with energy transfer, thermal-bioengineering, thermal radiation, combined mode heat transfer, coupled heat and mass transfer, and energy systems. Energy transport at the macro-scale and micro/nano-scales is also included. The internationally recognized team of authors adopt a consistent and systematic approach and writing style, including ample cross reference among topics, offering readers a user-friendly knowledgebase greater than the sum of its parts, perfect for frequent consultation. The Handbook of Thermal Science and Engineering is ideal for academic and professional readers in the traditional and emerging areas of mechanical engineering, chemical engineering, aerospace engineering, bioengineering, electronics fabrication, energy, and manufacturing concerned with the influence thermal phenomena.
Download or read book Enhanced Boiling Heat Transfer written by John R. Thome and published by CRC Press. This book was released on 1990-01-01 with total page 220 pages. Available in PDF, EPUB and Kindle. Book excerpt: This is a comprehensive survey of boiling heat transfer augmentation, one of the most dynamic areas in the field. The text covers fundamental aspects of boiling augmentation and provides an in-depth treatment of enhanced boiling surface applications in industry.
Download or read book Nanoporous Alumina written by Dusan Losic and published by Springer. This book was released on 2015-07-17 with total page 371 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book gives detailed information about the fabrication, properties and applications of nanoporous alumina. Nanoporous anodic alumina prepared by low-cost, simple and scalable electrochemical anodization process due to its unique structure and properties have attracted several thousand publications across many disciplines including nanotechnology, materials science, engineering, optics, electronics and medicine. The book incorporates several themes starting from the understanding fundamental principles of the formation nanopores and theoretical models of the pore growth. The book then focuses on describing soft and hard modification techniques for surface and structural modification of pore structures to tailor specific sensing, transport and optical properties of nano porous alumina required for diverse applications. These broad applications including optical biosensing, electrochemical DNA biosensing, molecular separation, optofluidics and drug delivery are reviewed in separated book chapters. The book appeals to researchers, industry professionals and high-level students.
Download or read book Encyclopedia Of Two phase Heat Transfer And Flow Iii Macro And Micro Flow Boiling And Numerical Modeling Fundamentals A 4 volume Set written by John R Thome and published by World Scientific. This book was released on 2018-03-13 with total page 1460 pages. Available in PDF, EPUB and Kindle. Book excerpt: Set III of this encyclopedia is a new addition to the previous Sets I and II. It contains 26 invited chapters from international specialists on the topics of numerical modeling of two-phase flows and evaporation, fundamentals of evaporation and condensation in microchannels and macrochannels, development and testing of micro two-phase cooling systems for electronics, and various special topics (surface wetting effects, microfin tubes, two-phase flow vibration across tube bundles). The chapters are written both by renowned university researchers and by well-known engineers from leading corporate research laboratories. Numerous 'must read' chapters cover the fundamentals of research and engineering practice on boiling, condensation and two-phase flows, two-phase heat transfer equipment, electronics cooling systems, case studies and so forth. Set III constitutes a 'must have' reference together with Sets I and II for thermal engineering researchers and practitioners.
Download or read book Heat Transfer Enhancement with Nanofluids written by Vincenzo Bianco and published by CRC Press. This book was released on 2015-04-01 with total page 473 pages. Available in PDF, EPUB and Kindle. Book excerpt: Nanofluids are gaining the attention of scientists and researchers around the world. This new category of heat transfer medium improves the thermal conductivity of fluid by suspending small solid particles within it and offers the possibility of increased heat transfer in a variety of applications. Bringing together expert contributions from
Download or read book Recent Advances in Material Manufacturing and Machine Learning written by Rajiv Gupta and published by CRC Press. This book was released on 2023-05-26 with total page 813 pages. Available in PDF, EPUB and Kindle. Book excerpt: The role of manufacturing in a country’s economy and societal development has long been established through their wealth generating capabilities. To enhance and widen our knowledge of materials and to increase innovation and responsiveness to ever-increasing international needs, more in-depth studies of functionally graded materials/tailor-made materials, recent advancements in manufacturing processes and new design philosophies are needed at present. The objective of this volume is to bring together experts from academic institutions, industries and research organizations and professional engineers for sharing of knowledge, expertise and experience in the emerging trends related to design, advanced materials processing and characterization, and advanced manufacturing processes.
Download or read book Nanofluid Boiling written by Ali Sadaghiani and published by Academic Press. This book was released on 2024-06-28 with total page 259 pages. Available in PDF, EPUB and Kindle. Book excerpt: Nanofluid Boiling presents valuable insights into boiling heat transfer mechanisms, offering state-of-the-art techniques for overcoming obstacles against nanofluid applications. In addition, the book points out emerging industrial applications and guides researchers and engineers in their research and design efforts. In addition, recommendations on future research directions and the design of systems involving nanofluids are presented at the end of each chapter. The book's authors comprehensively cover mechanisms, parametric effects and enhancement techniques in the boiling of nanofluids, providing updated, detailed information about recent developments and findings. Reveals insights into the findings and mechanisms of boiling heat transfer in nanofluids, guiding researchers and engineers in their research and design efforts Focuses on parametric effects such as nanofluid properties (size, concentration, nanoparticle type), preparation methods on heat transfer and critical heat flux mechanisms, bubble dynamics, flow patterns, and pressure drop Presents readers with scaling effects (from macro to microscale) relevant to nanofluid boiling
Download or read book Heat Transfer in Condensation and Boiling written by Karl Stephan and published by Springer Science & Business Media. This book was released on 2013-06-29 with total page 342 pages. Available in PDF, EPUB and Kindle. Book excerpt: I welcome the opportunity to have my book translated, because of the great emphasis on two-phase flow and heat transfer in the English-speaking world, as related to research, university education, and industrial practice. The 1988 Springer-Verlag edition of "Warmeiibergang beim Kondensieren und beim Sieden" has been enlarged to include additional material on falling film evaporation (Chapter 12) and pressure drop in two-phase flow (Chapter 13). Minor errors in the original text have also been corrected. I would like to express my sincere appreciation to Professor Green, Asso ciate Professor of German at Rensselaer, for his excellent translation and co operation. My thanks go also to Professor Bergles for his close attention to technical and linguistic details. He carefully read the typescript and made many comments and suggestions that helped to improve the manuscript. I hope that the English edition will meet with' a favorable reception and contribute to better understanding and to progress in the field of heat transfer in condensation and boiling. February 1992 K. Stephan Preface to the German-Language Edition This book is a continuation of the series "Heat and Mass Transfer" edited by U. Grigull, in which three volumes have already been published. Its aim is to acquaint students and practicing engineers with heat transfer during condensa tion and boiling, and is intended primarily for students and engineers in mechanical, chemical, electrical, and industrial processing engineering.
Download or read book Surface Modification of Nanoporous Anodic Alumina for Biomedical Applications written by Morteza Aramesh and published by . This book was released on 2015 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Nanoporous Alumina written by Dusan Losic and published by . This book was released on 2015 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: This book gives detailed information about the fabrication, properties and applications of nanoporous alumina. Nanoporous anodic alumina prepared by low-cost, simple and scalable electrochemical anodization process due to its unique structure and properties have attracted several thousand publications across many disciplines including nanotechnology, materials science, engineering, optics, electronics and medicine. The book incorporates several themes starting from the understanding fundamental principles of the formation nanopores and theoretical models of the pore growth. The book then focuses on describing soft and hard modification techniques for surface and structural modification of pore structures to tailor specific sensing, transport and optical properties of nanoporous alumina required for diverse applications. These broad applications including optical biosensing, electrochemical DNA biosensing, molecular separation, optofluidics, and drug delivery are reviewed in separated book chapters. The book appeals to researchers, industry professionals and high-level students.
Download or read book Fluid Mechanics and Fluid Power written by T. Prabu and published by Springer Nature. This book was released on 2021-08-03 with total page 901 pages. Available in PDF, EPUB and Kindle. Book excerpt: div="" style="" This book comprises select proceedings of the 46th National Conference on Fluid Mechanics and Fluid Power (FMFP 2019). The contents of this book focus on aerodynamics and flow control, computational fluid dynamics, fluid structure interaction, noise and aero-acoustics, unsteady and pulsating flows, vortex dynamics, nuclear thermal hydraulics, heat transfer in nanofluids, etc. This book serves as a useful reference beneficial to researchers, academicians and students interested in the broad field of mechanics. ^
Download or read book Advances in Heat Transfer written by and published by Academic Press. This book was released on 1998-05-18 with total page 467 pages. Available in PDF, EPUB and Kindle. Book excerpt: Advances in Heat Transfer
