Download or read book Novel Applications of Capacitive Micromachined Ultrasonic Transducers written by and published by . This book was released on 2007 with total page 328 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Interface Engineering of Capacitive Micromachined Ultrasonic Transducers for Medical Applications written by Der-Song Lin and published by Stanford University. This book was released on 2011 with total page 168 pages. Available in PDF, EPUB and Kindle. Book excerpt: Capacitive micromachined ultrasonic transducers (CMUTs), have been widely studied in academia and industry over the last decade. CMUTs provide many benefits over traditional piezoelectric transducers including improvement in performance through wide bandwidth, and ease of electronics integration, with the potential to batch fabricate very large 2D arrays with low-cost and high-yield. Though many aspects of CMUT technology have been studied over the years, packaging the CMUT into a fully practical system has not been thoroughly explored. Two important interfaces of packaging that this thesis explores are device encapsulation (the interface between CMUTs and patients) and full electronic integration of large scale 2D arrays (the interface between CMUTs and electronics). In the first part of the work, I investigate the requirements for the CMUT encapsulation. For medical usage, encapsulation is needed to electrically insulate the device, mechanically protect the device, and maintain transducer performance, especially the access of the ultrasound energy. While hermetic sealing can protect many other MEMS devices, CMUTs require mechanical interaction to a fluid, which makes fulfilling the previous criterion very challenging. The proposed solution is to use a viscoelastic material with the glass-transition-temperature lower than room temperature, such as Polydimethylsiloxane (PDMS), to preserve the CMUT static and dynamic performance. Experimental implementation of the encapsulated imaging CMUT arrays shows the device performance was maintained; 95 % of efficiency, 85% of the maximum output pressure, and 91% of the fractional bandwidth (FBW) can be preserved. A viscoelastic finite element model was also developed and shows the performance effects of the coating can be accurately predicted. Four designs, providing acoustic crosstalk suppression, flexible substrate, lens focusing, and blood flow monitoring using PDMS layer were also demonstrated. The second part of the work, presents contributions towards the electronic integration and packaging of large-area 2-D arrays. A very large 2D array is appealing for it can enable advanced novel imaging applications, such as a reconfigurable array, and a compression plate for breast cancer screening. With these goals in mind, I developed the first large-scale fully populated and integrated 2D CMUTs array with 32 by 192 elements. In this study, I demonstrate a flexible and reliable integration approach by successfully combining a simple UBM preparation technique and a CMUTs-interposer-ASICs sandwich design. The results show high shear strength of the UBM (26.5 g), 100% yield of the interconnections, and excellent CMUT resonance uniformity ([lowercase Sigma] = 0.02 MHz). As demonstrated, this allows for a large-scale assembly of a tile-able array by using an interposer. Interface engineering is crucial towards the development of CMUTs into a practical ultrasound system. With the advances in encapsulation technique with a viscoelastic polymer and the combination of the UBM technique to the TSV fabrication for electronics integration, a fully integrated CMUT system can be realized.

Download or read book Interface Engineering of Capacitive Micromachined Ultrasonic Transducers for Medical Applications written by Der-Song Lin and published by . This book was released on 2011 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: Capacitive micromachined ultrasonic transducers (CMUTs), have been widely studied in academia and industry over the last decade. CMUTs provide many benefits over traditional piezoelectric transducers including improvement in performance through wide bandwidth, and ease of electronics integration, with the potential to batch fabricate very large 2D arrays with low-cost and high-yield. Though many aspects of CMUT technology have been studied over the years, packaging the CMUT into a fully practical system has not been thoroughly explored. Two important interfaces of packaging that this thesis explores are device encapsulation (the interface between CMUTs and patients) and full electronic integration of large scale 2D arrays (the interface between CMUTs and electronics). In the first part of the work, I investigate the requirements for the CMUT encapsulation. For medical usage, encapsulation is needed to electrically insulate the device, mechanically protect the device, and maintain transducer performance, especially the access of the ultrasound energy. While hermetic sealing can protect many other MEMS devices, CMUTs require mechanical interaction to a fluid, which makes fulfilling the previous criterion very challenging. The proposed solution is to use a viscoelastic material with the glass-transition-temperature lower than room temperature, such as Polydimethylsiloxane (PDMS), to preserve the CMUT static and dynamic performance. Experimental implementation of the encapsulated imaging CMUT arrays shows the device performance was maintained; 95 % of efficiency, 85% of the maximum output pressure, and 91% of the fractional bandwidth (FBW) can be preserved. A viscoelastic finite element model was also developed and shows the performance effects of the coating can be accurately predicted. Four designs, providing acoustic crosstalk suppression, flexible substrate, lens focusing, and blood flow monitoring using PDMS layer were also demonstrated. The second part of the work, presents contributions towards the electronic integration and packaging of large-area 2-D arrays. A very large 2D array is appealing for it can enable advanced novel imaging applications, such as a reconfigurable array, and a compression plate for breast cancer screening. With these goals in mind, I developed the first large-scale fully populated and integrated 2D CMUTs array with 32 by 192 elements. In this study, I demonstrate a flexible and reliable integration approach by successfully combining a simple UBM preparation technique and a CMUTs-interposer-ASICs sandwich design. The results show high shear strength of the UBM (26.5 g), 100% yield of the interconnections, and excellent CMUT resonance uniformity ([lowercase Sigma] = 0.02 MHz). As demonstrated, this allows for a large-scale assembly of a tile-able array by using an interposer. Interface engineering is crucial towards the development of CMUTs into a practical ultrasound system. With the advances in encapsulation technique with a viscoelastic polymer and the combination of the UBM technique to the TSV fabrication for electronics integration, a fully integrated CMUT system can be realized.

Download or read book Piezoelectric and Acoustic Materials for Transducer Applications written by Ahmad Safari and published by Springer Science & Business Media. This book was released on 2008-09-11 with total page 483 pages. Available in PDF, EPUB and Kindle. Book excerpt: The book discusses the underlying physical principles of piezoelectric materials, important properties of ferroelectric/piezoelectric materials used in today’s transducer technology, and the principles used in transducer design. It provides examples of a wide range of applications of such materials along with the appertaining rationales. With contributions from distinguished researchers, this is a comprehensive reference on all the pertinent aspects of piezoelectric materials.

Download or read book Micromachined Ultrasonic Transducers written by and published by . This book was released on 1997 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: Microfabricated ultrasonic transducers have been generated which operate in both liquids and gases. Air coupled through transmission of aluminum was observed for the first time using a pair of 2.3 MHz transducers. The dynamic range of the transducers was 110 dB, and the received signal had an SNR of 30 dB. Air coupled through transmission of steel and glass has also been observed. A theoretical model for the transducers has been refined and agrees well with experimental results. A robust microfabrication process has been developed and was used to generate air transducers which resonate from 2 to 12 MHz, as well as immersion transducers that operate in water from 1 to 20 MHz with a 60 dB dynamic range. Optimized immersion and air transducers have been designed and a dynamic range above 110 dB is anticipated. This development effort finds applications in hydrophones, medical ultrasound, nondestructive evaluation, ranging, flow metering, and scanning tip force sensing and lithography.

Download or read book The Design Fabrication and Characterization of Capacitive Micromachined Ultrasonic Transducers for Imaging Applications written by Andrew Stephan Logan and published by . This book was released on 2010 with total page 155 pages. Available in PDF, EPUB and Kindle. Book excerpt: Capacitive micromachined ultrasonic transducers (CMUTs) have proven themselves to be excellent candidates for medical ultrasonic imaging applications. The use of semiconductor fabrication techniques facilitates the fabrication of high quality arrays of uniform cells and elements, broad acoustic bandwidth, the potential to integrate the transducers with the necessary electronics, and the opportunity to exploit the benefits of batch fabrication. In this thesis, the design, fabrication and testing of one- and two-dimensional CMUT arrays using a novel wafer bonding process whereby the membrane and the insulation layer are both silicon nitride is reported. A user-grown insulating membrane layer avoids the need for expensive SOI wafers, permits optimization of the electrode size, and allows more freedom in selecting the membrane thickness, while also enjoying the benefits of wafer bonding fabrication. Using a row-column addressing scheme for an NxN two-dimensional array permits three-dimensional imaging with a large reduction in the complexity of the array when compared to a conventional 2D array with connections to all N2 elements. Only 2N connections are required and the image acquisition rate has the potential to be greatly increased. A simplification of the device at the imaging end will facilitate the integration of a three-dimensional imaging CMUT array into either an endoscope or catheter which is the ultimate purpose of this research project. To date, many sizes of transducers which operate at different frequencies have been successfully fabricated. Initial characterization in terms of resonant frequency and, transmission and reception in immersion has been performed on most of the device types. Extensive characterization has been performed with a linear 32 element array transducer and a 32x32 element row-column transducer. Two- and three-dimensional phased array imaging has been demonstrated.

Download or read book Designing and Fabricating a Capacitive Micromachined Ultrasonic Transducer for Use in a Novel Photoacoustic Microscope written by Paul F. Cristman and published by . This book was released on 2016 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: In this thesis I present my work designing and fabricating a capacitive micromachined ultrasonic transducer (CMUT) for use in a novel photo-acoustic microscope. The CMUT device was designed to fit on the end of our collaborators' miniature fluorescent dual-axis confocal microscope to further increase the usefulness of the tool. Adding photo-acoustic imaging to the miniature fluorescent microscope eliminates the need for a fluorescent dye used specifically to identify vasculature. This allows dyes to be optimized to target tumor specific biomarkers to aid diagnosis and boundary definition. The device was designed so it could be packaged into a number of form factors for either handheld use or endoscopic screening. This is an important step for photo-acoustic microscopy because current laboratory systems are bulky and impractical for clinical use. Due to the advantages of the CMUT technology we were able to use a novel architecture to create a compact system.

Download or read book Application of Capacitive Micromachined Ultrasonic Transducers CMUTs for Chem Bio Sensing and Device Advances Enabling Acoustic Angiography written by Marzana Mantasha Mahmud and published by . This book was released on 2021 with total page 99 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Ultrasonic Transducer Materials written by O. E. Mattiat and published by Springer Science & Business Media. This book was released on 2013-03-13 with total page 194 pages. Available in PDF, EPUB and Kindle. Book excerpt: In recent years remarkable progress has been made in the development of materials for ultrasonic transducers. There is a continuing trend towards increasingly higher frequency ranges for the application of ultrasonic trans ducers in modern technology. The progress in this area has been especially rapid and articles and papers on the subject are scattered over numerous technical and scientific journals in this country and abroad. Although good books have appeared on ultrasonics in general and ultrasonic transducers in particular in which, for obvious reasons, materials play an important part, no comprehensive treatise is available that represents the state-of-the-art on modern ultrasonic transducer materials. This book intends to fill a need for a thorough review of the subject. Not all materials are covered of which, theoretically, ultrasonic trans ducers could be made but those that are or may be of technical impor tance and which have inherent electro acoustic transducer properties, i.e., materials that are either magnetostrictive, electrostrictive, or piezoelectric. The book has been devided into three parts which somewhat reflect the historic development of ultrasonic transducer materials for important tech nical application. Chapter 1 deals with magnetostrictive materials, magnetostrictive met als and their alloys, and magnetostrictive ferrites (polycrystalline ceramics). The metals are useful especially in cases where ruggednes of the transducers are of overriding importance and in the lower ultrasonic frequency range.

Download or read book Capacitive Micromachined Ultrasonic Transducers with Substrate embedded Springs written by Byung Chul Lee and published by . This book was released on 2015 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: After the first capacitive micromachined ultrasonic transducer (CMUT) was invented in 1994, it became one of the candidate technologies to advance the state-of-the-art of medical ultrasound imaging. Benefiting from its fabrication technique based on the semiconductor industry, CMUT technology has broadened the medical and therapeutic applications such as real-time volumetric ultrasound imaging, catheter-based forward-looking intravascular ultrasound (IVUS), photoacoustic imaging, high-intensity focused ultrasound (HIFU) and so on. In spite of many advantages, however, CMUT technology has been criticized with its relatively low transmit sensitivity (~10 kPa/V) or low average volume displacement efficiency (0.1 nm/V) as well as large drive and bias voltage requirements (in a range of a few hundreds of volts). In order to resolve these issues and open up new potential of clinical applications, this dissertation describes the design, fabrication, and system implementation of CMUTs with substrate-embedded springs, so-called post-CMUT (PCMUT). Since PCMUT structure resembles an ideal piston transducer, the improvements in performance mainly stem from the higher average displacement of the top plate for a given gap height. The overview of the first generation PCMUT is introduced and two main issues in simulation and fabrication aspects of the first generation PCMUT is discussed. To further improve the PCMUT device, a 3D finite element analysis (FEA) model of the PCMUT is demonstrated to predict the performance of the first generation PCMUT. In addition, the design guideline of the second generation PCMUT is proposed for achieving the maximum fractional bandwidth (100 %) as well as with the highest transmit sensitivity (~28 kPa/V). The second generation PCMUT is fabricated by using three combination MEMS processes: usage of two silicon-on-insulator (SOI) wafers, wafer bonding process, and wafer polishing process. The second generation PCMUT achieves high transmit sensitivity (~21 kPa/V) or large average volume displacement efficiency (1.1 nm/V) with a low bias voltage (55 V). Compared to a commercial piezoelectric transducer, the second generation PCMUT improves 2.75 times of the maximum output pressure and 5.25 times of the average volume displacement efficiency with respect to the same voltage. After fabrication and performance characterization of the second generation PCMUT, this dissertation demonstrates the feasibility of PCMUT to use it in medical imaging system by integrating PCMUT with a custom-built integrated circuit (IC). Photoacoustic imaging is also presented for one of its application examples.

Download or read book A Novel Fabrication Process for CMUTs in Air written by Samuel Kay Hord and published by . This book was released on 2017 with total page 72 pages. Available in PDF, EPUB and Kindle. Book excerpt: A novel fabrication method for producing capacitive micromachined ultrasonic transducers (CMUTs) is presented. The process uses conductive silicon on insulator (SOI) substrates to produce an unstressed transducer diaphragm. By etching release holes through the device layer and selectively removing the underlying buffered oxide (BOX) layer, an ultrasonic transducer can be made using only two photolithography steps. The process is described in detail, including models predicting the modal behavior and the collapse voltage of the device. The acoustical behavior of a perforated plate over a sealed cavity is modeled using mechano-acoustical circuit analysis. The device is found to produce sound despite the perforations so long as the holes are sufficiently small and the frequency of operation is sufficiently high. A pitch-catch measurement verifies the transduction of the device. To the author’s knowledge, this is the simplest method for CMUT fabrication to date.

Download or read book Capacitive Micromachined Ultrasonic Transducers CMUTs for Humidity Sensing written by Zhou Zheng and published by . This book was released on 2019 with total page 132 pages. Available in PDF, EPUB and Kindle. Book excerpt: In the last two decades, capacitive micromachined ultrasonic transducers (CMUTs) have proven themselves to be promising for various ultrasound imaging and chemical sensing applications. Although holding many benefits for ultrasound imaging, CMUTs have certain weaknesses such as the relatively low output pressure at transmission, which hinder their development in the diagnostic imaging application. In the sensing area, CMUTs have shown attractive features such as high mass sensitivity, miniaturized array configuration, and ease of functionalization. However, their potential for humidity sensing is less explored. The objectives of this thesis lie in two aspects. One is to offer a solution to overcome the limitation of low output pressure, and the other is to develop CMUTs as resonant gravimetric humidity sensors. The major efforts are made on the second task. For the first objective, a novel dual-element ultrasonic transducer is proposed. It incorporates two transducer technologies by using a circular piezoelectric element for ultrasound transmission and an annular CMUT element for reception. The hybrid transducer combines the broad bandwidth and high receive sensitivity of the CMUT and the high output power of the piezoelectric transducer to improve the overall sensitivity and axial resolution. The annular CMUT is designed, fabricated, and concentrically aligned with the piezoelectric probe via a custom housing. Immersion measurements show that the hybrid dual-element transducer improves the axial resolution by 25.58% and the signal-to-noise ratio by 8.55 dB over the commercial piezoelectric probe. For the second objective, a CMUT-based resonant humidity sensor is first developed with the direct wafer bonding technique. Graphene oxide (GO) is employed as the sensing material. Due to combination of the mass-sensitive CMUT and the moisture-sensitive GO, the sensor exhibits rapid response/recovery, good repeatability, and higher sensitivity than most of its competitors. The second generation of CMUT-based humidity sensors aims to further improve the relative humidity (RH) sensing performance by adopting the nitride-to-oxide wafer bonding technology for CMUT fabrication. In contrast to conventional wafer bonding CMUT processes that use expensive silicon-on-insulator (SOI) wafers to produce resonating membranes, the new process employs low-pressure chemical vapor deposition (LPCVD) silicon nitride as the membrane material. It provides thinner and lighter membranes, and thus more sensitive CMUT resonators. Additional benefits of the nitride-to-oxide wafer bonding technique are the reduced fabrication complexity and more controllable membrane thickness. Finally, a dual-frequency (10/14 MHz) CMUT is developed using this fabrication technique. It generates two RH response curves and can provide more accurate RH sensing. Due to the independence of the two resonance frequencies, the dual-frequency CMUT also shows great potential for identification of different chemicals. This thesis demonstrates that CMUT sensors can be strong candidates for miniaturized, highly sensitive, and reliable humidity sensors.

Download or read book Capacitive Micromachined Ultrasonic Transducers CMUTs for Therapeutic Applications written by Hyo-Seon Yoon and published by . This book was released on 2015 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: High-intensity focused ultrasound (HIFU) is a noninvasive method to treat a variety of diseases. Most of the HIFU machines in clinic typically consist of a piezoelectric transducer array and an imaging system for temperature monitoring and anatomical location guidance. One of the limitations of piezoelectric transducers is self-heating, which requires cooling systems to protect both transducers and patients. Capacitive micromachined ultrasonic transducers (CMUTs) are another type of transducers fabricated with silicon micromachining. CMUTs are promising candidates as therapeutic transducers, as they experience a lot less self-heating compared to piezoelectric transducers. This dissertation mainly focuses on describing the design, simulation, fabrication, characterization, and experimental results of CMUTs for HIFU applications. Single-element transducers are fabricated using local oxidation of silicon (LOCOS)-wafer-bonding process. The measurement part compares the self-heating of a PZT and a CMUT, and discusses the charging issue of CMUTs. Geometric focusing using multiple single-element CMUTs is also demonstrated. The fabrication of 1-D CMUT arrays to enhance the output pressure for HIFU applications is discussed. Higher output pressure of a CMUT cell can be achieved by adding one extra fabrication step to the existing fabrication process. Two-dimensional transducer arrays are required for electronic focusing and beam steering. An 8-channel continuous wave (CW) excitation system is developed to drive a 2-D CMUT array. This 8-channel system minimizes the system complexity without significant loss of focusing capability, compared to a full system with hundreds to thousands of channels. The first successful 2-D CMUT array fabricated using the thick-buried-oxide (BOX) process is presented. The breakdown issue of the insulation layer observed in the test stage is investigated as well. Another type of 2-D CMUT array fabricated using the sacrificial-release process is also tested for HIFU applications. Using the 8-channel CW excitation system, the 2-D CMUT array has proven to be able to produce enough output pressure for thermal ablation. This dissertation presents the result of ex-vivo experiments, which created thermal lesions on bovine tissue using a CMUT array for the first time.

Download or read book Novel Architectures for Capacitive Micromachined Sensors and Actuators written by Hani Tawfik and published by . This book was released on 2019 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: "This work presents novel architectures for improving the performance of capacitive-based micromachined thermal detectors, ultrasonic transducers, and multiplexers. The proposed designs are implemented in a pure-play commercial process, which is known for its reliability and cost-effectiveness. In addition, several performance-limitation issues are tackled. Furthermore, a novel approach is proposed for implementing standalone MEMS arrays, to avoid the complicated and expensive post-processing of complementary metal-oxide-semiconductor (CMOS) wafers.The first part of this work presents a novel dual-level capacitive bimorphous thermal detector architecture that is prototyped in the commercial PolyMUMPs by MEMSCAP. The dual-level design exhibits a 6.5 fF/°C sensitivity which is over 3 times higher than traditional single-level designs and it has a base capacitance that is over twice as large. The proposed architecture mitigates an inherent trade-off between thermal sensitivity and base capacitance. Other challenges facing bimorphous thermal detectors are addressed as well. This work also presents, a compensation mechanism for shocks and the ambient temperature. In addition, a material selection study for the bimorph layers concluded a significant performance enhancement of using silicon-carbide (SiC) with polyimide. Moreover, a method was developed for utilizing a positive photoresist as a sacrificial layer that alleviates the restrictions on material-selection for the layers of the bimorphs.The second part of this study presents a reduced-gap implementation of a 3.33-MHz capacitive micromachined ultrasonic transducer (CMUT) in the PolyMUMPs technology. The design provides a bias voltage supply reduction that is four times less compared to the traditional architecture to achieve a sufficient acoustic pressure. Also, a novel operation mechanism is demonstrated for ultrasonic testing underwater, and this mechanism employs the surface-tension forces between the surfaces of the water and the ultrasonic probe. The proposed meniscus-mode mechanism amplifies the ultrasonic signal more than the traditional fully-immersed setup by a factor of 2.6; this is demonstrated experimentally in the study.The final part proposes a novel switching design for multiplexing, and it targets low-frequency applications. The inline torsional electrostatic MEMS multiplexer (ITEM2) architecture is presented. In the study, a theoretical analysis of the structure's snap-down voltage is derived. By combining the novel architectures for thermal detectors and CMUTs presented with the proposed ITEM2 design, a stand-alone MEMS array solution can be a low-cost alternative to the traditional monolithic and hybrid integration with the electronics. The study presents an implementation of an 8 × 8 thermal detectors array that is routed using micromachined bypass-bridges and MEMS multiplexers." --

Download or read book MEMS Technology for Biomedical Imaging Applications written by Qifa Zhou and published by MDPI. This book was released on 2019-10-23 with total page 218 pages. Available in PDF, EPUB and Kindle. Book excerpt: Biomedical imaging is the key technique and process to create informative images of the human body or other organic structures for clinical purposes or medical science. Micro-electro-mechanical systems (MEMS) technology has demonstrated enormous potential in biomedical imaging applications due to its outstanding advantages of, for instance, miniaturization, high speed, higher resolution, and convenience of batch fabrication. There are many advancements and breakthroughs developing in the academic community, and there are a few challenges raised accordingly upon the designs, structures, fabrication, integration, and applications of MEMS for all kinds of biomedical imaging. This Special Issue aims to collate and showcase research papers, short commutations, perspectives, and insightful review articles from esteemed colleagues that demonstrate: (1) original works on the topic of MEMS components or devices based on various kinds of mechanisms for biomedical imaging; and (2) new developments and potentials of applying MEMS technology of any kind in biomedical imaging. The objective of this special session is to provide insightful information regarding the technological advancements for the researchers in the community.

Download or read book Characterization of Multiple Moving Membrane Capacitive Micromachined Ultrasonic Transducer written by Md. Iftekharul Islam and published by . This book was released on 2019 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: A newly developed multiple moving membrane capacitive micromachined ultrasonic transducer (M3-CMUT) is fabricated and characterized in this thesis. Unlike the single vibrating membrane in the conventional capacitive micromachined ultrasonic transducer (CMUT), the novel design involves two deflectable membranes suspended over a fixed bottom electrode. In the presence of bias, both of the membranes deflect simultaneously, which results in a smaller cavity compared to a CMUT. To understand the basics of a capacitive transducer, an equivalent mass-spring-capacitor model of CMUT was reported. The results of this analytical model were used to develop the finite element models (FEM) of CMUT and more complex M3-CMUT in COMSOL Multiphysics software. The electromechanical analysis of these models was conducted to observe their operating conditions. Following the modeling and analysis, several single-cell, 1-D, and 2-D arrays of these devices were fabricated using PolyMUMPs technology, a sacrificial fabrication technique for the MEMS transducers. The electrical and acoustic characterizations of the fabricated devices were performed to measure the actual transducer properties. The measured data and the model results were found to be in good agreement. It was observed from the electrical impedance measurements that a higher membrane deflection was achieved in the double membrane device. The reduction in the cavity of M3-CMUT enhanced the sensitivity of the transducer. The acoustic characterization using a pitch-catch experimental setup demonstrated that the novel M3-CMUT could be used as an ultrasonic transducer. The velocity and attenuation of the acoustic waves, when the transducer used as both the transmitter and the receiver, were found to be very close to the theoretical value.

Download or read book Air coupled Capacitive Micromachined Ultrasonic Transducers Based on Annular Cell Geometry written by Shuai Na and published by . This book was released on 2017 with total page 130 pages. Available in PDF, EPUB and Kindle. Book excerpt: Air-coupled ultrasound is gaining increasing industry momentum due to the demands and development of non-destructive evaluation (NDE) of aerospace composite materials. Currently, the micromachining technology has advanced such that vacuum cavities sealed by thin plates, known as Capacitive Micromachined Ultrasonic Transducers (CMUTs), can be fabricated through silicon micromachining processes in a low cost manner. Given the thin plates, a CMUT is able to vibrate with a low mechanical impedance and thus a high coupling efficiency with the ambient atmosphere. Nevertheless, air-coupled applications are still highly limited by the transmit power of air-coupled CMUTs. A circle is the routine geometry in most CMUT cell designs. Even though efforts have been put forward to address the limitations of circular design in terms of sensitivity, more investigation about other cell geometries is prudent. In this work, a novel air-coupled CMUT design with annular cell geometry is proposed. Finite element analysis and experimental studies demonstrated its significant improvement in transmit efficiency over the conventional circular-cell CMUTs. A lumped element model was constructed to facilitate a better understanding and provide an efficient design technique of the annular CMUT. Three optimization schemes were developed to optimize the transmit efficiency and achieve a reasonable comparison between the novel annular and conventional circular CMUT cells. Based on the lumped models, a design optimization flow chart was constructed to facilitate the analytical optimization of the three schemes. To further enhance the transmit power as well as offer depth focusing, a 9-element concentric annular-cell array was designed, fabricated, and characterized. A pillar-free etching process was developed to create the deep large-area cavities. The cross-talk between neighbouring cells and the plate-cracking phenomenon were discussed with suggestions for improvement being provided. This study provides a systematic framework for designing and studying annular-cell CMUTs and demonstrates their great potential in transmitting high-power ultrasound in air.