Download or read book Nonlinear Creep and Creep Recovery of Die cast Aluminum Alloys written by Jay C. Dandrea and published by . This book was released on 2008 with total page 102 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Creep and Relaxation in Die cast Aluminum Alloys at Elevated Temperature written by Aaron Nimityongskul and published by . This book was released on 2005 with total page 242 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Recovery Behavior of Cold worked Metals written by J. L. Lytton and published by . This book was released on 1963 with total page 88 pages. Available in PDF, EPUB and Kindle. Book excerpt: Recovery of tensile flow stress of four binary aluminum alloys and of the high-purity base alum inum was studied under no-load conditionat tem peratures of 80, 120, 160, and 200 C, and under conditions of creep strain at 160 C, for recovery times up to 1,000 hr. At the three higher recovery temperatures, 120, 160, and 200 C, and for the longer recovery times, the alloys Al-Mg, Al Zn, and Al-Cu all experienced a greater degree of recovery than the high-purity base aluminum. Of these three alloys, the Al-Cu alloy clearly exhibited the greatest degree of recovery. The Al-Ag alloy was excluded from the comparison be cause of an apparent strengthening process which occurred during recovery. All the alloys showed a strong increase in flow-stress recovery during creep strain over that experienced during no-load recovery; however, the relative order of recovery for the different alloys did not change.

Download or read book Compressive and Tensile Creep of 7075 T6 and 2024 T3 Aluminum alloy Sheet written by George J. Heimerl and published by . This book was released on 1959 with total page 44 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Creep and Stress rupture Properties of Some Permanent mold Casting Aluminum Alloys written by P. J. Pankaskie and published by . This book was released on 1951 with total page 36 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Creep Recovery of Aluminium Alloy DTD 2L42 written by James Henderson (B.Sc., A.Inst.P.) and published by . This book was released on 1964 with total page 31 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Creep of Cast 390 Aluminum Alloys written by Brenda R. Jones and published by . This book was released on 1989 with total page 268 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Creep and Creep Recovery of 2618 T61 Aluminum Under Variable Temperature written by Uee Wan Cho and published by . This book was released on 1983 with total page 25 pages. Available in PDF, EPUB and Kindle. Book excerpt: Creep and creep recovery data are reported for pure tension of 2618 aluminum alloy under variable temperature between 200 deg. C and 230 deg. C. Varying temperature experiments involved an abrupt temperature increase and a linearly increasing and decreasing temperature at a constant stress of 137.9 MPa (20 ksi). A temperature-compensated time by Sherby and Dorn was employed to represent the effect of temperature. The temperature history dependent theory described the test data quiet well for both increasing and decreasing temperature. The apparent activation energy of this alloy was found to be 49,000 cal/mole.

Download or read book Creep and Recovery of 2618 T61 Aluminum Alloy at Low Stress Levels written by Jow-Lian Ding and published by . This book was released on 1980 with total page 100 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Hot Deformation and Processing of Aluminum Alloys written by and published by . This book was released on 2011 with total page 585 pages. Available in PDF, EPUB and Kindle. Book excerpt: PREFACE This book offers readers a fairly comprehensive discussion of the hot working of aluminum and aluminum alloys. It is intended to provide an explanation of the possible microstructural developments that can occur with hot deformation of a variety of alloys and the kind of mechanical properties that can be anticipated. The microstructures that evolve with torsion, compression, extrusion and rolling are presented based on extensive analysis from polarized light optical microscopy (POM), transmission electron microscopy (TEM), x-ray diffraction (XRD) scanning electron-microscopy with electron backscatter imaging (SEM-EBSD) and orientation imaging microscopy (OIM). The microstructural analysis leads to detailed explanations of dynamic recovery (DRV), static recovery (SRV), discontinuous dynamic recrystallization (dDRX), discontinuous static recrystallization (dSRX), grain defining dynamic recovery (gDRV) (formerly geometric dynamic recrystallization gDRX) and continuous dynamic recrystallization involving a single phase (cDRX/1-phase) and multiple phases, (cDRX/2-phase). Hot working is carefully explained in the context of other elevated temperature phenomena, some of which overlap hot working. These include creep, superplasticity, cold working and annealing. Creep plasticity occurs at both warm and hot working temperatures, but is usually associated with lower strain-rates and relatively small strains. On the other hand superplasticity involves high tensile strains at similar temperatures, but lower strain rates than utilized in hot working--

Download or read book Chemical Abstracts written by and published by . This book was released on 2002 with total page 2566 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Viscoelastic Materials written by Roderic S. Lakes and published by Cambridge University Press. This book was released on 2009-04-27 with total page 481 pages. Available in PDF, EPUB and Kindle. Book excerpt: This graduate text on viscoelastic materials addresses design applications as diverse as earplugs, computer disks and medical diagnostics.

Download or read book Metals Abstracts written by and published by . This book was released on 1994 with total page 1620 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book ASM Handbook written by ASM International. Handbook Committee and published by ASM International(OH). This book was released on 2000 with total page 1242 pages. Available in PDF, EPUB and Kindle. Book excerpt: This index eliminates that need to search through multiple back-of-the-book indexes to find where a subject is addressed. The A-to-Z listing will help users find important handbook content in volumes where they may not have thought to look.

Download or read book Technical Abstract Bulletin written by and published by . This book was released on 1965 with total page 914 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Scientific and Technical Aerospace Reports written by and published by . This book was released on 1987 with total page 938 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Metals Abstracts Index written by and published by . This book was released on 1996 with total page 1622 pages. Available in PDF, EPUB and Kindle. Book excerpt: