Download or read book Additively Manufactured Inconel 718 written by Dunyong Deng and published by Linköping University Electronic Press. This book was released on 2018-01-24 with total page 82 pages. Available in PDF, EPUB and Kindle. Book excerpt: Additive manufacturing (AM), also known as 3D printing, has gained significant interest in aerospace, energy, automotive and medical industries due to its capabilities of manufacturing components that are either prohibitively costly or impossible to manufacture by conventional processes. Among the various additive manufacturing processes for metallic components, electron beam melting (EBM) and selective laser melting (SLM) are two of the most widely used powder bed based processes, and have shown great potential for manufacturing high-end critical components, such as turbine blades and customized medical implants. The futures of the EBM and SLM are doubtlessly promising, but to fully realize their potentials there are still many challenges to overcome. Inconel 718 (IN718) is a nickel-base superalloy and has impressive combination of good mechanical properties and low cost. Though IN718 is being mostly used as a turbine disk material now, the initial introduction of IN718 was to overcome the poor weldability of superalloys in 1960s, since sluggish precipitation of strengthening phases ?’/?’’ enables good resistance to strain-age cracking during welding or post weld heat treatment. Given the similarity between AM and welding processes, IN718 has been widely applied to the metallic AM field to facilitate the understandings of process-microstructure-property relationships. The work presented in this licentiate thesis aims to better understand microstructures and mechanical properties EBM and SLM IN718, which have not been systematically investigated. Microstructures of EBM and SLM IN718 have been characterized with scanning electron microscopy (SEM), transmission electron microscopy (TEM) and correlated with the process conditions. Monotonic mechanical properties (e.g., Vickers microhardness and tensile properties) have also been measured and rationalized with regards to the microstructure evolutions before and after heat treatments. For EBM IN718, the results show the microstructure is not homogeneous but dependant on the location in the components, and the anisotropic mechanical properties are probably attributed to alignment of porosities rather than texture. Post heat treatment can slightly increase the mechanical strength compared to the as-manufactured condition but does not alter the anisotropy. SLM IN718 shows significantly different microstructure and mechanical properties to EBM IN718. The as-manufactured SLM IN718 has very fine dendritic microstructure and Laves phases in the interdendrites, and is “work-hardened” by the residual strains and dislocations present in the material. Mechanical properties are different between horizontally and vertically built samples, and heat treatment can minimize this difference. Results from this licentiate thesis provide the basis for the further research on the cyclic mechanical properties of EBM and SLM IN718, which would be the focus of following phase of the Ph.D. research.

Download or read book Additive Manufacturing written by T.S. Srivatsan and published by CRC Press. This book was released on 2015-09-25 with total page 448 pages. Available in PDF, EPUB and Kindle. Book excerpt: Get Ready for the Future of Additive ManufacturingAdditive Manufacturing: Innovations, Advances, and Applications explores the emerging field of additive manufacturing (AM)-the use of 3D printing to make prototype parts on demand. Often referred to as the third industrial revolution, AM offers many advantages over traditional manufacturing. This pr

Download or read book Proceedings of the 9th International Symposium on Superalloy 718 Derivatives Energy Aerospace and Industrial Applications written by Eric Ott and published by Springer. This book was released on 2018-05-12 with total page 1092 pages. Available in PDF, EPUB and Kindle. Book excerpt: This technical meeting will focus on Alloy 718 and Superalloys in this class relative to alloy and process development, production, product applications, trends and the development of advanced modeling tools. The symposium provides an opportunity for authors to present technical advancements relative to a broad spectrum of areas while assessing their impact on related fields associated with this critical alloy group. There are continuing innovations relative to these alloys as well as novel processing techniques which continue to extend applications in very challenging environments ranging from corrosion resistance in the deep sea to high-stressed space applications.

Download or read book Welding Metallurgy and Weldability of Nickel Base Alloys written by John C. Lippold and published by John Wiley & Sons. This book was released on 2011-09-20 with total page 370 pages. Available in PDF, EPUB and Kindle. Book excerpt: The most up-to-date coverage of welding metallurgy aspects and weldability issues associated with Ni-base alloys Welding Metallurgy and Weldability of Nickel-Base Alloys describes the fundamental metallurgical principles that control the microstructure and properties of welded Ni-base alloys. It serves as a practical how-to guide that enables engineers to select the proper alloys, filler metals, heat treatments, and welding conditions to ensure that failures are avoided during fabrication and service. Chapter coverage includes: Alloying additions, phase diagrams, and phase stability Solid-solution strengthened Ni-base alloys Precipitation strengthened Ni-base alloys Oxide dispersion strengthened alloys and nickel aluminides Repair welding of Ni-base alloys Dissimilar welding Weldability testing High-chromium alloys used in nuclear power applications With its excellent balance between the fundamentals and practical problem solving, the book serves as an ideal reference for scientists, engineers, and technicians, as well as a textbook for undergraduate and graduate courses in welding metallurgy.

Download or read book Heat Treater s Guide written by Harry Chandler and published by ASM International. This book was released on 1996-01-01 with total page 690 pages. Available in PDF, EPUB and Kindle. Book excerpt: The material is contained in more than 500 datasheet articles, each devoted exclusively to one particular alloy, a proven format first used in the complementary guide for irons and steels. For even more convenience, the datasheets are arranged by alloy groups: nickel, aluminum, copper, magnesium, titanium, zinc and superalloys. The book provides very worthwhile and practical information in such areas as: compositions, trade names, common names, specifications (both U.S. and foreign), available products forms, typical applications, and properties (mechanical, fabricating, and selected others). This comprehensive resource also covers the more uncommon alloys by groups in the same datasheet format. Included are: refractory metals and alloys (molybdenum, tungsten, niobium, tantalum), beryllium copper alloys, cast and P/M titanium parts, P/M aluminum parts, lead and lead alloys, tin-rich alloys, and sintering copper-base materials (copper-tin, bronze, brass, nickel silvers).

Download or read book The Superalloys written by Roger C. Reed and published by Cambridge University Press. This book was released on 2008-07-31 with total page 363 pages. Available in PDF, EPUB and Kindle. Book excerpt: Superalloys are unique high-temperature materials used in gas turbine engines, which display excellent resistance to mechanical and chemical degradation. This book introduces the metallurgical principles which have guided their development. Suitable for graduate students and researchers, it includes exercises and additional resources at www.cambridge.org/9780521859042.

Download or read book Alloy Design and Characterization of Strengthened Nickel based Superalloys for Additive Manufacturing written by Jinghao Xu and published by Linköping University Electronic Press. This book was released on 2021-01-28 with total page 63 pages. Available in PDF, EPUB and Kindle. Book excerpt: Nickel-based superalloys, an alloy system bases on nickel as the matrix element with the addition of up to 10 more alloying elements including chromium, aluminum, cobalt, tungsten, molybdenum, titanium, and so on. Through the development and improvement of nickel-based superalloys in the past century, they are well proved to show excellent performance at the elevated service temperature. Owing to the combination of extraordinary high-temperature mechanical properties, such as monotonic and cyclic deformation resistance, fatigue crack propagation resistance; and high-temperature chemical properties, such as corrosion and oxidation resistance, phase stability, nickel-based superalloys are widely used in the critical hot-section components in aerospace and energy generation industries. The success of nickel-based superalloy systems attributes to both the well-tailored microstructures with the assistance of carefully doped alloying elements, and the intently developed manufacturing processes. The microstructure of the modern nickel-based superalloys consists of a two-phase configuration: the intermetallic precipitates (Ni,Co)3(Al,Ti,Ta) known as γ′ phase dispersed into the austenite γ matrix, which is firstly introduced in the 1940s. The recently developed additive manufacturing (AM) techniques, acting as the disruptive manufacturing process, offers a new avenue for producing the nickel-based superalloy components with complicated geometries. However, γ′ strengthened nickel-based superalloys always suffer from the micro-cracking during the AM process, which is barely eliminated by the process optimization. On this basis, the new compositions of γ′ strengthened nickel-based superalloy adapted to the AM process are of great interest and significance. This study sought to design novel γ′ strengthened nickel-based superalloys readily for AM process with limited cracking susceptibility, based on the understanding of the cracking mechanisms. A two-parameter model is developed to predict the additive manufacturability for any given composition of a nickel-based superalloy. One materials index is derived from the comparison of the deformation-resistant capacity between dendritic and interdendritic regions, while another index is derived from the difference of heat resistant capacity of these two spaces. By plotting the additive manufacturability diagram, the superalloys family can be categorized into the easy-to-weld, fairly-weldable, and non-weldable regime with the good agreement of the existed knowledge. To design a novel superalloy, a Cr-Co-Mo-W-Al-Ti-Ta-Nb-Fe-Ni alloy family is proposed containing 921,600 composition recipes in total. Through the examination of additive manufacturability, undesired phase formation propensity, and the precipitation fraction, one composition of superalloy, MAD542, out of the 921,600 candidates is selected. Validation of additive manufacturability of MAD542 is carried out by laser powder bed fusion (LPBF). By optimizing the LPBF process parameters, the crack-free MAD542 part is achieved. In addition, the MAD542 superalloy shows great resistance to the post-processing treatment-induced cracking. During the post-processing treatment, extensive annealing twins are promoted to achieve the recrystallization microstructure, ensuring the rapid reduction of stored energy. After ageing treatment, up to 60-65% volume fraction of γ′ precipitates are developed, indicating the huge potential of γ′ formation. Examined by the high-temperature slow strain rate tensile and constant loading creep testing, the MAD542 superalloy shows superior strength than the LPBF processed and hot isostatic pressed plus heat-treated IN738LC superalloy. While the low ductility of MAD542 is existed, which is expected to be improved by modifying the post-processing treatment scenarios and by the adjusting building direction in the following stages of the Ph.D. research. MAD542 superalloy so far shows both good additive manufacturability and mechanical potentials. Additionally, the results in this study will contribute to a novel paradigm for alloy design and encourage more γ′-strengthened nickel-based superalloys tailored for AM processes in the future.

Download or read book Multiscale Modeling of Additively Manufactured Metals written by Yi Zhang and published by Elsevier. This book was released on 2020-06-29 with total page 252 pages. Available in PDF, EPUB and Kindle. Book excerpt: Multiscale Modeling of Additively Manufactured Metals: Application to Laser Powder Bed Fusion Process provides comprehensive coverage on the latest methodology in additive manufacturing (AM) modeling and simulation. Although there are extensive advances within the AM field, challenges to predictive theoretical and computational approaches still hinder the widespread adoption of AM. The book reviews metal additive materials and processes and discusses multiscale/multiphysics modeling strategies. In addition, coverage of modeling and simulation of AM process in order to understand the process-structure-property relationship is reviewed, along with the modeling of morphology evolution, phase transformation, and defect formation in AM parts. Residual stress, distortion, plasticity/damage in AM parts are also considered, with scales associated with the spatial, temporal and/or material domains reviewed. This book is useful for graduate students, engineers and professionals working on AM materials, equipment, process, development and modeling. - Includes the fundamental principles of additive manufacturing modeling techniques - Presents various modeling tools/software for AM modeling - Discusses various design methods and how to optimize the AM process using these models

Download or read book Sustainable Manufacturing written by Kapil Gupta and published by Elsevier. This book was released on 2021-03-30 with total page 457 pages. Available in PDF, EPUB and Kindle. Book excerpt: Sustainable Manufacturing examines the overall sustainability of a wide range of manufacturing processes and industrial systems. With chapters addressing machining, casting, additive and gear manufacturing processes; and hot topics such as remanufacturing, life cycle engineering, and recycling, this book is the most complete guide to this topic available. Drawing on experts in both academia and industry, coverage addresses theoretical developments and practical improvements from research and innovations. This unique book will advise readers on how to achieve sustainable manufacturing processes and systems, and further the clean and safe environment. This handbook is a part of the four volume set entitled Handbooks in Advanced Manufacturing. The other three address Advanced Machining and Finishing, Advanced Welding and Deforming, and Additive Manufacturing. - Provides basic to advanced level information on various aspects of sustainable manufacturing - Presents the strategies and techniques to achieve sustainability in numerous areas of manufacturing and industrial engineering such as environmentally benign machining, sustainable additive manufacturing, remanufacturing and recycling, sustainable supply chain, and life cycle engineering - Combines contributions from experts in academia and industry with the latest research and case studies - Explains how to attain a clean, green, and safe environment via sustainable manufacturing - Presents recent developments and suggests future research directions

Download or read book Superalloys written by Matthew J. Donachie and published by ASM International. This book was released on 2002 with total page 439 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book covers virtually all technical aspects related to the selection, processing, use, and analysis of superalloys. The text of this new second edition has been completely revised and expanded with many new figures and tables added. In developing this new edition, the focus has been on providing comprehensive and practical coverage of superalloys technology. Some highlights include the most complete and up-to-date presentation available on alloy melting. Coverage of alloy selection provides many tips and guidelines that the reader can use in identifying an appropriate alloy for a specific application. The relation of properties and microstructure is covered in more detail than in previous books.

Download or read book Rapid Prototyping of Biomaterials written by Roger Narayan and published by Woodhead Publishing. This book was released on 2014-02-13 with total page 333 pages. Available in PDF, EPUB and Kindle. Book excerpt: Rapid Prototyping of Biomaterials: Principles and Applications provides a comprehensive review of established and emerging rapid prototyping technologies (such as bioprinting) for medical applications. Rapid prototyping, also known as layer manufacturing, additive manufacturing, solid freeform fabrication, or 3D printing, can be used to create complex structures and devices for medical applications from solid, powder, or liquid precursors. Following a useful introduction, which provides an overview of the field, the book explores rapid prototyping of nanoscale biomaterials, biosensors, artificial organs, and prosthetic limbs. Further chapters consider the use of rapid prototyping technologies for the processing of viable cells, scaffolds, and tissues. With its distinguished editor and international team of renowned contributors, Rapid Prototyping of Biomaterials is a useful technical resource for scientists and researchers in the biomaterials and tissue regeneration industry, as well as in academia. - Comprehensive review of established and emerging rapid prototyping technologies (such as bioprinting) for medical applications - Chapters explore rapid prototyping of nanoscale biomaterials, biosensors, artificial organs, and prosthetic limbs - Examines the use of rapid prototyping technologies for the processing of viable cells, scaffolds, and tissues

Download or read book Superalloys written by Elihu F. Bradley and published by ASM International(OH). This book was released on 1988 with total page 296 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Additive Manufacturing Applications for Metals and Composites written by Balasubramanian, K.R. and published by IGI Global. This book was released on 2020-06-19 with total page 348 pages. Available in PDF, EPUB and Kindle. Book excerpt: Additive manufacturing (AM) of metals and composites using laser energy, direct energy deposition, electron beam methods, and wire arc melting have recently gained importance due to their advantages in fabricating the complex structure. Today, it has become possible to reliably manufacture dense parts with certain AM processes for many materials, including steels, aluminum and titanium alloys, superalloys, metal-based composites, and ceramic matrix composites. In the near future, the AM material variety will most likely grow further, with high-performance materials such as intermetallic compounds and high entropy alloys already under investigation. Additive Manufacturing Applications for Metals and Composites is a pivotal reference source that provides vital research on advancing methods and technological developments within additive manufacturing practices. Special attention is paid to the material design of additive manufacturing of parts, the choice of feedstock materials, the metallurgical behavior and synthesis principle during the manufacturing process, and the resulted microstructures and properties, as well as the relationship between these factors. While highlighting topics such as numerical modeling, intermetallic compounds, and statistical techniques, this publication is ideally designed for students, engineers, researchers, manufacturers, technologists, academicians, practitioners, scholars, and educators.

Download or read book TMS 2018 147th Annual Meeting Exhibition Supplemental Proceedings written by The Minerals, Metals & Materials Society and published by Springer. This book was released on 2018-02-03 with total page 898 pages. Available in PDF, EPUB and Kindle. Book excerpt: This collection features papers presented at the 147th Annual Meeting & Exhibition of The Minerals, Metals & Materials Society.

Download or read book Laser Based Additive Manufacturing written by Narendra B. Dahotre and published by John Wiley & Sons. This book was released on 2022-08-01 with total page 308 pages. Available in PDF, EPUB and Kindle. Book excerpt: Laser-Based Additive Manufacturing Explore laser-based additive manufacturing processes via multi-scale modeling and computer simulation In Laser-Based Additive Manufacturing: Modeling, Simulation, and Experiments, a distinguished team of researchers delivers an incisive framework for understanding materials processing using laser-based additive manufacturing (LAM). The book describes the use of computational modeling and simulation to explore and describe the LAM technique, to improve the compositional, phase, and microstructural evolution of the material, and to enhance the mechanical, chemical, and functional properties of the manufactured components. The accomplished authors combine a comprehensive overview of multi-scale modeling and simulation with experimental and practical observations, offering a systematic review of laser-material interactions in advanced LAM processes. They also describe the real-world applications of LAM, including component processing and surface functionalization. In addition to explorations of residual stresses, three-dimensional defects, and surface physical texture in LAM, readers will also find: A thorough introduction to additive manufacturing (AM), including the advantages of AM over conventional manufacturing and the challenges involved with using the technology A comprehensive exploration of computation materials science, including length- and time-scales in materials modeling and the current state of computational modeling in LAM Practical discussions of laser-material interaction in LAM, including the conversion of light energy to heat, modes of heat dissipation, and the dynamics of the melt-pool In-depth examinations of the microstructural and mechanical aspects of LAM integrated with modeling Perfect for materials scientists, mechanical engineers, and physicists, Laser-Based Additive Manufacturing: Modeling, Simulation, and Experiments is perfect for anyone seeking an insightful treatment of this cutting-edge technology in the areas of alloys, ceramics, and composites.

Download or read book Laser Cladding of Metals written by Pasquale Cavaliere and published by Springer Nature. This book was released on 2020-11-05 with total page 444 pages. Available in PDF, EPUB and Kindle. Book excerpt: Laser cladding is an additive manufacturing technology capable of producing coatings due to the surface fusion of metals. The selected powder is fed into a focused laser beam to be melted and deposited as coating. This allows to apply material in a selected way onto those required sections of complex components. The process main properties are the production of a perfect metallurgically bonded and fully dense coatings; the minimal heat affected zone and low dilution between the substrate and filler material resulting in functional coatings that perform at reduced thickness, so fewer layers are applied; fine, homogeneous microstructure resulting from the rapid solidification rate that promotes wear resistance of carbide coatings; near net-shape weld build-up requires little finishing effort; extended weldability of sensitive materials like carbon-rich steels or nickel-based superalloys that are difficult or even impossible to weld using conventional welding processes; post-weld heat treatment is often eliminated as the small heat affected zone minimizes component stress; excellent process stability and reproducibility because it is numerical controlled welding process. The typical applications are the dimensional restoration; the wear and corrosion protection; additive manufacturing. The wide range of materials that can be deposited and its suitability for treating small areas make laser cladding particularly appropriate to tailor surface properties to local service requirements and it opens up a new perspective for surface engineered materials. The main key aspect to be scientifically and technologically explored are the type of laser; the powders properties; the processing parameters; the consequent microstructural and mechanical properties of the processed material; the capability of fabrication of prototypes to rapid tooling and rapid manufacturing. Distills critical concepts, methods, and applications from leading full-length chapters, along with the authors’s own deep understanding of the material taught, into a concise yet rigorous graduate and advanced undergraduate text; Reinforces concepts covered with detailed solutions to illuminating and challenging industrial applications; Discusses current and future applications of laser cladding in additive manufacturing.

Download or read book Additive Manufacturing of Shape Memory Materials written by Mehrshad Mehrpouya and published by Elsevier. This book was released on 2024-10-23 with total page 546 pages. Available in PDF, EPUB and Kindle. Book excerpt: Additive Manufacturing of Shape Memory Materials: Techniques, Characterization, Modeling, and Applications outlines an array of techniques and applications for additive manufacturing (AM) and the use of various shape memory materials, covering corrosion properties, material sensitivity to thermal, magnetic, and electrical effects, as well as sensitivity of shape memory properties to AM parameters, including part geometry effects and post-process treatments.Design for AM and a number of different AM methods are discussed, with materials covered including shape memory alloys, shape memory polymers, high-temperature shape memory alloys, and magnetic shape memory alloys. Characterization and modeling methods are also included, as is a chapter dedicated to real-world applications of these production techniques and materials. - Provides an overview of various shape memory materials, their additive manufacturing techniques and processes, their applications, and opportunities and challenges related to their production and use - Outlines the thermomechanical and functional properties of shape memory alloys that can be applied to their additive manufacturing processes - Covers techniques for additive manufacturing of shape memory polymers, shape memory alloys, high-temperature shape memory alloys, and magnetic shape memory alloys - Discusses characterization, post-processing, modeling, and applications of shape memory materials