Download or read book Management of Metal finishing Sludge written by E. P. Crumpler and published by . This book was released on 1977 with total page 76 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Management of Metal finishing Sludge written by E. P. Crumpler and published by . This book was released on 1977 with total page 62 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Control and Treatment Technology for the Metal Finishing Industry written by and published by . This book was released on 1980 with total page 64 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Wastewater and Sludge Control in the Canadian Metal Finishing Industry written by L. Buffa and published by Water Pollution Control Directorate : Supply and Services Canada. This book was released on 1976 with total page 52 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Hazardous Waste Reducation in the Metal Finishing Industry written by PRC Environmental Management, Inc and published by William Andrew. This book was released on 1989-12-31 with total page 232 pages. Available in PDF, EPUB and Kindle. Book excerpt: "From the Foreword: " This book presents the results of a waste audit study for the metal finishing industry. The study, carried out for the State of California but applicable for metal finishers elsewhere, identifies opportunities for waste reduction available to the metal finishing industry and develops procedures that can be used by metal finishers to assess their own waste reduction opportunities. The study emphasizes technologies available to small- and medium-sized metal finishing plants. Typically, these shops operate a variety of physical, chemical, and electrochemical processes. Chemical processes include degreasing, cleaning, pickling, etching, coating, and electroless plating. Electrochemical processes include plating and anodizing. The tasks included in the study were: (1) selecting metal finishing plants to include in the study, (2) performing a waste audit at each selected plant, (3) developing recommendations for implementing waste reduction technologies at each audited plant, (4) discussing with facility representatives the feasibility of implementing the waste reduction recommendations, and (5) developing this waste audit study report and methodology. The study identifies three categories of waste reduction technologies that are available to metal finishers: (1) source reduction, (2) recycling and resource recovery, and (3) alternative treatment. The costs associated with implementing these technologies range from a few hundred dollars for making simple improvements in housekeepiing and minor process modifications to tens of thousands of dollars for installing recovery or treatment units. The benefits realized from implementing such improvements include reductions inmaterial purchase and waste disposal costs, as well as reduction in the liability

Download or read book The Operation and Maintenance of Surface Finishing Wastewater Treatment Systems written by Clarence H. Roy and published by William Andrew. This book was released on 1988 with total page 216 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Environmental Pollution Control Alternatives written by and published by . This book was released on 1982 with total page 46 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Sludge Handling Dewatering and Disposal Alternatives for the Metal Finishing Industry written by Industrial Environmental Research Laboratory (Cincinnati, Ohio) and published by . This book was released on 1982 with total page 36 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Plating Waste Sludge Metal Recovery written by Malcolm T. Hepworth and published by . This book was released on 1985 with total page 198 pages. Available in PDF, EPUB and Kindle. Book excerpt: The U.S. Army Toxic and Hazardous Materials Agency has requested that AMAX Extractive Research & Development, Inc. conduct a five-phase program to review literature on the current state-of-the-art in metal recovery from plating wastes, to propose a typical plating sludge composition and aging treatment in lieu of actual U.S. Army plating wastes), to develop a research and design test plan for treating this typical plating sludge, to conduct the test program, and to summarize the results in a final report. The final report proposes a sulfuric acid leach of hydroxide plating sludges, containing copper, cadmium, zinc, nickel, iron, and chromium, to extract greater than 99 percent of the heavy metal values, followed by lime treatment of the resulting filter cake to render it nonhazardous to EP testing. The sulfuric acid leach extract may be treated by selective sulfide precipitation at a controlled pH regime in order to produce a mixed sulfide of copper and cadmium with most of the zinc present in the original extract separate from a leach liquor containing more than 98 percent of the chromium, which does not form a sulfide precipitate, Nickel and iron are not selectively separated under the sulfide precipitation conditions. However, a solvent extraction process using di(2-ethyl-hexyl) phosphoric acid can be used for recovering nickel, iron, and chromium from the resulting filtrate. Originator-supplied keywords: Plating sludge, Acid leach, EP toxicity, Metals, Separation, Extraction, and Recovery.

Download or read book Treatment of Metal Wastestreams written by United States. Environmental Protection Agency. Office of Water Programs and published by . This book was released on 2003 with total page 180 pages. Available in PDF, EPUB and Kindle. Book excerpt: This manual is designed to train personnel in the safe and effective operation and maintenance of wastewater treatment facilities for electroplanting, metal finishing, and printed circuit board manufacturing. It emphasizes how to operate and maintain facilities that neutralize acidic and basic waters, treat wastes containing metals, destroy cyanide, and also treat complexed metal wastes.

Download or read book A State of the art Review of Metal Finishing Waste Treatment written by Battelle Memorial Institute and published by . This book was released on 1968 with total page 100 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Control and Treatment Technology for the Metal Finishing Industry written by and published by . This book was released on 1981 with total page 52 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Waste Water Treatment and Reuse in a Metal Finishing Job Shop written by Williams (S.K.) Company and published by . This book was released on 1974 with total page 76 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Annual Conference on Advanced Pollution Control for the Metal Finishing Industry written by and published by . This book was released on 1978 with total page 166 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Water and Waste water Management in the Metal Finishing Industry written by Binnie & Partners and published by . This book was released on 1987 with total page 52 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Alternative Treatment of Organic Solvents and Sludges from Metal Finishing Operations written by and published by . This book was released on 1983 with total page 736 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Waste Treatment in the Metal Manufacturing Forming Coating and Finishing Industries written by Lawrence K. Wang and published by CRC Press. This book was released on 2016-04-19 with total page 508 pages. Available in PDF, EPUB and Kindle. Book excerpt: Comprehensive in its scope and directly applicable to daily waste management problems of specific industries, Waste Treatment in the Metal Manufacturing, Forming, Coating, and Finishing Industries covers hazardous industrial waste treatment, renovation, and reuse in the metal manufacturing, forming, coating, enameling, and finishing industries. It