Download or read book Light Trapping in Crystalline Silicon Solar Cells written by Ulf Blieske and published by . This book was released on 1989 with total page 108 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Light Trapping in Thin Crystalline Silicon Solar Cells written by James A. Rand and published by . This book was released on 1990 with total page 336 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Light Trapping in High efficiency Crystalline Silicon Solar Cells written by Johannes Eisenlohr and published by . This book was released on 2017 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Light Trapping in Thin Film Crystalline Silicon Solar Cells written by Javaneh Boroumand Azad and published by . This book was released on 2017 with total page 99 pages. Available in PDF, EPUB and Kindle. Book excerpt: This dissertation presents numerical and experimental studies of a unified light trapping approach that is extremely important for all practical solar cells. A 2D hexagonal Bravais lattice diffractive pattern is studied in conjunction with the verification of the reflection mechanisms of single and double layer anti-reflective coatings in the broad range of wavelength 400 nm - 1100 nm. By varying thickness and conformity, we obtained the optimal parameters which minimize the broadband reflection from the nanostructured crystalline silicon surface over a wide range of angle 0°-65°. While the analytical design of broadband, angle independent anti-reflection coatings on nanostructured surfaces remains a scientific challenge, numerical optimization proves a viable alternative, paving the path towards practical implementation of the light trapping solar cells. A 3 [micrometer] thick light trapping solar cell is modeled in order to predict and maximize combined electron-photon harvesting in ultrathin crystalline silicon solar cells. It is shown that the higher charge carrier generation and collection in this design compensates the absorption and recombination losses and ultimately results in an increase in energy conversion efficiency. Further, 20 [micrometer] and 100 [micrometer] thick functional solar cells with the light trapping scheme are studied. The efficiency improvement is observed numerically and experimentally due to photon absorption enhancement in the light trapping cells with respect to a bare cell of same thickness.

Download or read book Thin Film Crystalline Silicon Solar Cells written by Rolf Brendel and published by John Wiley & Sons. This book was released on 2011-02-15 with total page 306 pages. Available in PDF, EPUB and Kindle. Book excerpt: This introduction to the physics of silicon solar cells focuses on thin cells, while reviewing and discussing the current status of the important technology. An analysis of the spectral quantum efficiency of thin solar cells is given as well as a full set of analytical models. This is the first comprehensive treatment of light trapping techniques for the enhancement of the optical absorption in thin silicon films.

Download or read book Crystalline Silicon Solar Cells written by Saleem Hussain Zaidi and published by Springer Nature. This book was released on 2021-08-02 with total page 271 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book focuses on crystalline silicon solar cell science and technology. It is written from the perspective of an experimentalist with extensive hands-on experience in modeling, fabrication, and characterization. A practical approach to solar cell fabrication is presented in terms of its three components: materials, electrical, and optical. The materials section describes wafer processing methods including saw damage removal, texturing, diffusion, and surface passivation. The electrical section focuses on formation of ohmic contacts on n and p-doped surfaces. The optical section illustrates light interaction with textured silicon surfaces in terms of geometrical, diffractive and physical optics, transmission, and surface photovoltage (SPV) spectroscopy. A final chapter analyzes performance of solar cells, fabricated with a wide range of process parameters. A brief economic analysis on the merits of crystalline silicon-based photovoltaic technology as a cottage industry is also included./div This professional reference will be an important resource for practicing engineers and technicians working with solar cell and PV manufacturing and renewable energy technologies, as well as upper-level engineering and material science students. Presents a practical approach to solar cell fabrication, and characterization; Offers modular methodology with detailed equipment and process parameters supported by experimental results; Includes processing diagrams and tables for 16% efficient solar cell fabrication.

Download or read book Light Trapping and Reflection Control in a Crystalline Silicon Solar Cell written by Patrick Ross Campbell and published by . This book was released on 1989 with total page 292 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Ultrathin Crystalline Silicon Solar Cells Incorporating Advanced Light trapping Structures written by Matthew S. Branham and published by . This book was released on 2015 with total page 110 pages. Available in PDF, EPUB and Kindle. Book excerpt: Solar photovoltaics, which convert the energy potential of photons from the sun directly into electrical power, hold immense promise as a cornerstone of a clean energy future. Yet their cost remains greater than that of conventional energy sources in most markets and a barrier to large-scale adoption. Crystalline silicon modules, with a 90% share of the worldwide photovoltaic market, have witnessed a precipitous drop in price over the last decade. But going forward, further evolutionary cost reduction will be difficult given the significant cost of the silicon wafer alone - roughly 35% of the module. Dramatically reducing the thickness of silicon used to make a solar cell from the current 350 [mu]m could rewrite the economics of photovoltaics. For thin-film crystalline silicon solar cells to deliver the anticipated cost benefits of reduced material requirements, it is essential that they also yield power conversion efficiencies comparable to commercial solar cells. A significant hurdle to realizing elevated efficiency in crystalline silicon films thinner than 20 [mu]m is the loss of current resulting from reduced photon absorption. A range of light management structures have been proposed in the literature to address this issue and many have been demonstrated to provide high absorption across the spectral range relevant to crystalline silicon, but their promise has yet to be realized in an active photovoltaic device. The focus of this thesis is the development of an experimental platform and fabrication process to evaluate the effectiveness of theoretically-designed light-trapping structures in functional photovoltaic devices. The experimental effort yielded 10-pm-thick crystalline silicon solar cells with a peak short-circuit current of 34.5 mA cm-2 and power conversion efficiency of 15.7%. The record performance for a crystalline silicon photovoltaic of such thinness is enabled by an advanced light-trapping design incorporating a 2D photonic crystal and a rear dielectric/reflector stack. A parallel line of questioning addressed in this thesis is whether periodic wavelength-scale optical structures are superior to periodic or random structures with geometric-optics-scale features. Through the synthesis of experimental and theoretical evidence, the case is constructed that wavelength-scale light-trapping structures are in fact comparable to conventional random pyramid surface structures for broad-spectrum absorption in silicon solar cells as thin as 5 [mu]m. These results have important implications for the design of cost-effective and manufacturable light-trapping structures for ultrathin crystalline silicon solar cells.

Download or read book Light Trapping in Monocrystalline Silicon Solar Cells Using Random Upright Pyramids written by Salman Manzoor and published by . This book was released on 2014 with total page 109 pages. Available in PDF, EPUB and Kindle. Book excerpt: Crystalline silicon has a relatively low absorption coefficient, and therefore, in thin silicon solar cells surface texturization plays a vital role in enhancing light absorption. Texturization is needed to increase the path length of light through the active absorbing layer. The most popular choice for surface texturization of crystalline silicon is the anisotropic wet-etching that yields pyramid-like structures. These structures have shown to be both simple to fabricate and efficient in increasing the path length; they outperform most competing surface texture. Recent studies have also shown these pyramid-like structures are not truly square-based 54.7 degree pyramids but have variable base angles and shapes. In addition, their distribution is not regular -- as is often assumed in optical models -- but random. For accurate prediction of performance of silicon solar cells, it is important to investigate the true nature of the surface texture that is achieved using anisotropic wet-etching, and its impact on light trapping. We have used atomic force microscopy (AFM) to characterize the surface topology by obtaining actual height maps that serve as input to ray tracing software. The height map also yields the base angle distribution, which is compared to the base angle distribution obtained by analyzing the angular reflectance distribution measured by spectrophotometer to validate the shape of the structures. Further validation of the measured AFM maps is done by performing pyramid density comparison with SEM micrograph of the texture. Last method employed for validation is Focused Ion Beam (FIB) that is used to mill the long section of pyramids to reveal their profile and so from that the base angle distribution is measured. After that the measured map is modified and the maps are generated keeping the positional randomness (the positions of pyramids) and height of the pyramids the same, but changing their base angles. In the end a ray tracing software is used to compare the actual measured AFM map and also the modified maps using their reflectance, transmittance, angular scattering and most importantly path length enhancement, absorbance and short circuit current with lambertian scatterer.

Download or read book Anti reflection and Light Trapping in c Si Solar Cells written by Chetan Singh Solanki and published by Springer. This book was released on 2017-06-30 with total page 210 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book offers essential insights into c-Si based solar cells and fundamentals of reflection, refraction, and light trapping. The basic physics and technology for light trapping in c-Si based solar cells are covered, from traditional to advanced light trapping structures. Further, the book discusses the latest developments in plasmonics for c-Si solar cell applications, along with their future scope and the requirements for further research. The book offers a valuable guide for graduate students, researchers and professionals interested in the latest trends in solar cell technologies.

Download or read book Light Trapping by Micro and Nano hole Texturing of Single crystalline Silicon Solar Cells written by and published by . This book was released on 2016 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Texturization and Light Trapping in Silicon Solar Cells written by U. Gangopadhyay and published by . This book was released on 2009 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: Reduction of optical losses in both mono and multicrystalline silicon solar cells by surface texturing is one of the important issues of modern silicon photovoltaics. Texturing of the front surface of silicon solar cells has been modeled and analysed with reference to the reduction in reflection co-efficient and increase in optical trapping. Significant enhancement in open circuit voltage and short circuit current has been achieved through such texturing of the front surface of mono-silicon solar cells. A proper optimisation of texture angle appears to be important for the best performance of the solar cells. An alternative way of reducing the surface reflection and enhancement of the cell parameters is to produce to passive front surface porous silicon layer. An analysis of the characteristics of a porous silicon layer shows that the morphology of the layer is an important design parameter. To realise the structures in practice, several methods are available, but many of this method are either not cost effective or commercially non available. In order to achieve good uniformity of pyramidal textured structure of the silicon surface, a mixture of NaOH/KOH and isopropyl alcohol (IPA) is generally used for texturization of mono crystalline solar cells. However, due to high cost of IPA, there is always search for alternative source. This source should not only be cost effective but should also result in reduced interfacial energy between silicon and ionised electrolyte chemical solution to achieve sufficient wet-ability for the silicon surface in order to enhance pyramid nucleation. Different novel texturization techniques for monocrystalline silicon are descried in this chapter including solar cells performance. For multicrystalline silicon (mc-Si) solar cells, the standard alkaline solution of NaOH/KOH does not produced textured surface of good quality so as to give satisfactory open circuit voltage and efficiency. This is because of grain boundary delineation with step formed between successive grains of different orientations. Different novel texturization techniques for multicrystalline silicon are also included in this book including solar cells performance.

Download or read book Photon Management in Solar Cells written by Ralf B. Wehrspohn and published by John Wiley & Sons. This book was released on 2015-06-08 with total page 376 pages. Available in PDF, EPUB and Kindle. Book excerpt: Written by renowned experts in the field of photon management in solar cells, this one-stop reference gives an introduction to the physics of light management in solar cells, and discusses the different concepts and methods of applying photon management. The authors cover the physics, principles, concepts, technologies, and methods used, explaining how to increase the efficiency of solar cells by splitting or modifying the solar spectrum before they absorb the sunlight. In so doing, they present novel concepts and materials allowing for the cheaper, more flexible manufacture of solar cells and systems. For educational purposes, the authors have split the reasons for photon management into spatial and spectral light management. Bridging the gap between the photonics and the photovoltaics communities, this is an invaluable reference for materials scientists, physicists in industry, experimental physicists, lecturers in physics, Ph.D. students in physics and material sciences, engineers in power technology, applied and surface physicists.

Download or read book Low Cost Manufacturing of Light Trapping Features on Multi crystalline Silicon Solar Cells written by Amine Berrada Sounni and published by . This book was released on 2010 with total page 132 pages. Available in PDF, EPUB and Kindle. Book excerpt: An experimental study was conducted in order to determine low cost methods to improve the light trapping ability of multi-crystalline solar cells. We focused our work on improving current wet etching methods to achieve the desired light trapping features which consists in micro-scale trenches with parabolic cross-sectional profiles with a target aspect ratio of 1.0. The jet etching with a hard mask method, which consists in impinging a liquid mixture of hydrofluoric, nitric and acetic acids through the opening of hard mask, was developed. First, a computational fluid dynamics simulation was conducted to determine the desired jet velocity and angle to be used in our experiments. We find that using a jet velocity of 3 m/s and a jetting angle of 45° yields the necessary flow characteristics for etching high aspect ratio features. Second, we performed experiments to determine the effect of jet etching using a photo-resist mask and thermally grown silicon oxide mask on multiple silicon substrates : 100, 110, 111 and multi-crystalline silicon. Compared to a baseline of etching with no jet, we find that the jet etching process can improve the light trapping ability of the baseline features by improving their aspect ratio up to 65.2% and their light trapping ability up to 38.1%. The highest aspect ratio achieved using the jet etching process was 0.62. However, it must be noted that the repeatability of the results was not consistent: significant variations in the results of the same experiment occurred, making the jet etching process promising but difficult to control. Finally, we performed a cost analysis in order to determine the minimum efficiency that a jet etching process would have to achieve to be cost competitive and its corresponding features aspect ratio. We find that a minimum cell efficiency of 16.63% and feature aspect ratios of 0.57 are necessary for cost competitiveness with current solar cell manufacturing technology.

Download or read book Introduction to Light Trapping in Solar Cell and Photo detector Devices written by Stephen J. Fonash and published by Elsevier. This book was released on 2014-09-15 with total page 76 pages. Available in PDF, EPUB and Kindle. Book excerpt: New Approaches to Light Trapping in Solar Cell Devices discusses in detail the use of photonic and plasmonic effects for light trapping in solar cells. It compares and contrasts texturing, the current method of light-trapping design in solar cells, with emerging approaches employing photonic and plasmonic phenomena. These new light trapping methods reduce the amount of absorber required in a solar cell, promising significant cost reduction and efficiency. This book highlights potential advantages of photonics and plasmonics and describes design optimization using computer modeling of these approaches. Its discussion of ultimate efficiency possibilities in solar cells is grounded in a review of the Shockley-Queisser analysis; this includes an in-depth examination of recent analyses building on that seminal work.

Download or read book Light Trapping for Thin Silicon Solar Cells by Femtosecond Laser Texturing written by and published by . This book was released on 2012 with total page 5 pages. Available in PDF, EPUB and Kindle. Book excerpt: Femtosecond laser texturing is used to create nano- to micron-scale surface roughness that strongly enhances light-trapping in thin crystalline silicon solar cells. Light trapping is crucial for thin solar cells where a single light-pass through the absorber is insufficient to capture the weakly absorbed red and near-infrared photons, especially with an indirect-gap semiconductor absorber layer such as crystalline Si which is less than 20 um thick. We achieve enhancement of the optical absorption from light-trapping that approaches the Yablonovitch limit.

Download or read book Pigmented Materials for Light Trapping in Thin film Polycrystalline Silicon Solar Cells written by Jeffrey Ellis Cotter and published by . This book was released on 1996 with total page 282 pages. Available in PDF, EPUB and Kindle. Book excerpt: