Download or read book Learning Autodesk Inventor 2022 bundled with Robot Kit written by Randy Shih and published by . This book was released on 2021-08 with total page 500 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Learning Autodesk Inventor 2022 written by Randy Shih and published by SDC Publications. This book was released on 2021-08 with total page 510 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book will teach you everything you need to know to start using Autodesk Inventor 2022 with easy to understand, step-by-step tutorials. This book features a simple robot design used as a project throughout the book. You will learn to model parts, create assemblies, run simulations and even create animations of your robot design. An unassembled version of the same robot used throughout the book can be bundled with the book. No previous experience with Computer Aided Design(CAD) is needed since this book starts at an introductory level. The author begins by getting you familiar with the Inventor interface and its basic tools. You will start by learning to model simple robot parts and before long you will graduate to creating more complex parts and multi-view drawings. Along the way you will learn the fundamentals of parametric modeling through the use of geometric constraints and relationships. You will also become familiar with many of Inventor's powerful tools and commands that enable you to easily construct complex features in your models. Also included is coverage of gears, gear trains and spur gear creation using Autodesk Inventor. This book continues by examining the different mechanisms commonly used in walking robots. You will learn the basic types of planar four-bar linkages commonly used in mechanical designs and how to use the GeoGebra Dynamic Geometry software to simulate and analyze 2D linkages. Using the knowledge you gained about linkages and mechanism, you will learn how to modify your robot and change its behavior by modifying or creating new parts. In the final chapter of this book you learn how to combine all the robot parts into assemblies and then run motion analysis. You will finish off your project by creating 3D animations of your robot in action. There are many books that show you how to perform individual tasks with Autodesk Inventor, but this book takes you through an entire project and shows you the complete engineering process. By the end of this book you will have modeled and assembled nearly all the parts that make up the TAMIYA® Mechanical Tiger and can start building your own robot.

Download or read book Learning Autodesk Inventor 2024 written by Randy Shih and published by SDC Publications. This book was released on 2023-06 with total page 515 pages. Available in PDF, EPUB and Kindle. Book excerpt: • Teaches beginners how to use Autodesk Inventor with easy to understand tutorials • Features a simple robot design used as a project throughout the book • Covers modeling, gear creation, linkage analysis, assemblies, simulations and 3D animation • Available with an optional robot kit This book will teach you everything you need to know to start using Autodesk Inventor 2024 with easy to understand, step-by-step tutorials. This book features a simple robot design used as a project throughout the book. You will learn to model parts, create assemblies, run simulations and even create animations of your robot design. An unassembled version of the same robot used throughout the book can be bundled with the book. No previous experience with Computer Aided Design(CAD) is needed since this book starts at an introductory level. The author begins by getting you familiar with the Inventor interface and its basic tools. You will start by learning to model simple robot parts and before long you will graduate to creating more complex parts and multi-view drawings. Along the way you will learn the fundamentals of parametric modeling through the use of geometric constraints and relationships. You will also become familiar with many of Inventor's powerful tools and commands that enable you to easily construct complex features in your models. Also included is coverage of gears, gear trains and spur gear creation using Autodesk Inventor. This book continues by examining the different mechanisms commonly used in walking robots. You will learn the basic types of planar four-bar linkages commonly used in mechanical designs and how to use the GeoGebra Dynamic Geometry software to simulate and analyze 2D linkages. Using the knowledge you gained about linkages and mechanism, you will learn how to modify your robot and change its behavior by modifying or creating new parts. In the final chapter of this book you learn how to combine all the robot parts into assemblies and then run motion analysis. You will finish off your project by creating 3D animations of your robot in action. There are many books that show you how to perform individual tasks with Autodesk Inventor, but this book takes you through an entire project and shows you the complete engineering process. By the end of this book you will have modeled and assembled nearly all the parts that make up the TAMIYA® Mechanical Tiger and can start building your own robot.

Download or read book Learning Autodesk Inventor 2025 with Robot Kit written by Randy Shih and published by . This book was released on 2024-07 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Learning Autodesk Inventor 2020 Book Robot Kit written by Randy H. Shih and published by . This book was released on 2019-07 with total page 500 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Learning Autodesk Inventor 2021 with Robot Kit written by Randy Shih and published by . This book was released on 2020-08 with total page 512 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Learning SOLIDWORKS 2022 bundled with Robot Kit written by Randy Shih and published by . This book was released on 2022-03 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Learning Autodesk Inventor 2025 written by Randy Shih and published by SDC Publications. This book was released on with total page 515 pages. Available in PDF, EPUB and Kindle. Book excerpt: • Teaches beginners how to use Autodesk Inventor with easy to understand tutorials • Features a simple robot design used as a project throughout the book • Covers modeling, gear creation, linkage analysis, assemblies, simulations and 3D animation • Available with an optional robot kit This book will teach you everything you need to know to start using Autodesk Inventor 2025 with easy to understand, step-by-step tutorials. This book features a simple robot design used as a project throughout the book. You will learn to model parts, create assemblies, run simulations and even create animations of your robot design. An unassembled version of the same robot used throughout the book can be bundled with the book. No previous experience with Computer Aided Design (CAD) is needed since this book starts at an introductory level. The author begins by getting you familiar with the Inventor interface and its basic tools. You will start by learning to model simple robot parts and before long you will graduate to creating more complex parts and multi-view drawings. Along the way you will learn the fundamentals of parametric modeling through the use of geometric constraints and relationships. You will also become familiar with many of Inventor's powerful tools and commands that enable you to easily construct complex features in your models. Also included is coverage of gears, gear trains and spur gear creation using Autodesk Inventor. This book continues by examining the different mechanisms commonly used in walking robots. You will learn the basic types of planar four-bar linkages commonly used in mechanical designs and how to use the GeoGebra Dynamic Geometry software to simulate and analyze 2D linkages. Using the knowledge you gained about linkages and mechanism, you will learn how to modify your robot and change its behavior by modifying or creating new parts. In the final chapter of this book you learn how to combine all the robot parts into assemblies and then run motion analysis. You will finish off your project by creating 3D animations of your robot in action. There are many books that show you how to perform individual tasks with Autodesk Inventor, but this book takes you through an entire project and shows you the complete engineering process. By the end of this book you will have modeled and assembled nearly all the parts that make up the TAMIYA® Mechanical Tiger and can start building your own robot.

Download or read book Autodesk Inventor 2022 A Tutorial Introduction written by L. Scott Hansen and published by SDC Publications. This book was released on with total page 490 pages. Available in PDF, EPUB and Kindle. Book excerpt: This unique text and video set presents a thorough introduction to Autodesk Inventor for anyone with little or no prior experience with CAD software. It can be used in virtually any setting from four year engineering schools to on-the-job use or self-study. Unlike other books of its kind, it begins at a very basic level and ends at a very advanced level. It’s perfect for anyone interested in learning Autodesk Inventor quickly and effectively using a “learning by doing” approach. Additionally, the extensive videos that are included with this book make it easier than ever to learn Inventor by clearly demonstrating how to use its tools. The philosophy behind this book is that learning computer aided design programs is best accomplished by emphasizing the application of the tools. Students also seem to learn more quickly and retain information and skills better if they are actually creating something with the software program. The driving force behind this book is “learning by doing.” The instructional format of this book centers on making sure that students learn by doing and that students can learn from this book on their own. In fact, this is one thing that differentiates this book from others: the emphasis on being able to use the book for self-study. The presentation of Autodesk Inventor is structured so that no previous knowledge of any CAD program is required. This book uses the philosophy that Inventor is mastered best by concentrating on applying the program to create different types of solid models, starting simply and then using the power of the program to progressively create more complex solid models. The Drawing Activities at the end of each chapter are more complex iterations of the part developed by each chapter’s objectives. Since CAD programs are highly visual, there are graphical illustrations showing how to use the program. This reinforces the “learn by doing” philosophy since a student can see exactly what the program shows, and then step through progressive commands to implement the required operations. Rather than using a verbal description of the command, a screen capture of each command is replicated. Included Videos Each book includes access to extensive video training created by author Scott Hansen. The videos follow along with the table of contents of the book. Each chapter has one or more videos in which the author demonstrates how to use the tools that are covered in that chapter. Most videos follow an exercise from start to finish. The exercises created in the video are very similar to the exercise found in the corresponding chapter. Throughout the videos Scott Hansen describes how to perform each step, the reason behind these steps, and some of the other options available with the various tools. The author's clear and simple description of each exercise is a perfect companion to the text and makes learning Autodesk Inventor easier than ever. There are twenty-seven videos with three hours and forty-five minutes of training in total.

Download or read book Learning Autodesk Inventor 2023 written by Randy Shih and published by SDC Publications. This book was released on 2022-07 with total page 510 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book will teach you everything you need to know to start using Autodesk Inventor 2023 with easy to understand, step-by-step tutorials. This book features a simple robot design used as a project throughout the book. You will learn to model parts, create assemblies, run simulations and even create animations of your robot design. An unassembled version of the same robot used throughout the book can be bundled with the book. No previous experience with Computer Aided Design(CAD) is needed since this book starts at an introductory level. The author begins by getting you familiar with the Inventor interface and its basic tools. You will start by learning to model simple robot parts and before long you will graduate to creating more complex parts and multi-view drawings. Along the way you will learn the fundamentals of parametric modeling through the use of geometric constraints and relationships. You will also become familiar with many of Inventor's powerful tools and commands that enable you to easily construct complex features in your models. Also included is coverage of gears, gear trains and spur gear creation using Autodesk Inventor. This book continues by examining the different mechanisms commonly used in walking robots. You will learn the basic types of planar four-bar linkages commonly used in mechanical designs and how to use the GeoGebra Dynamic Geometry software to simulate and analyze 2D linkages. Using the knowledge you gained about linkages and mechanism, you will learn how to modify your robot and change its behavior by modifying or creating new parts. In the final chapter of this book you learn how to combine all the robot parts into assemblies and then run motion analysis. You will finish off your project by creating 3D animations of your robot in action. There are many books that show you how to perform individual tasks with Autodesk Inventor, but this book takes you through an entire project and shows you the complete engineering process. By the end of this book you will have modeled and assembled nearly all the parts that make up the TAMIYA® Mechanical Tiger and can start building your own robot.

Download or read book Learning Autodesk Inventor 2021 written by Randy Shih and published by SDC Publications. This book was released on 2020-07-22 with total page 510 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book will teach you everything you need to know to start using Autodesk Inventor 2021 with easy to understand, step-by-step tutorials. This book features a simple robot design used as a project throughout the book. You will learn to model parts, create assemblies, run simulations and even create animations of your robot design. An unassembled version of the same robot used throughout the book can be bundled with the book. No previous experience with Computer Aided Design(CAD) is needed since this book starts at an introductory level. The author begins by getting you familiar with the Inventor interface and its basic tools. You will start by learning to model simple robot parts and before long you will graduate to creating more complex parts and multi-view drawings. Along the way you will learn the fundamentals of parametric modeling through the use of geometric constraints and relationships. You will also become familiar with many of Inventor's powerful tools and commands that enable you to easily construct complex features in your models. Also included is coverage of gears, gear trains and spur gear creation using Autodesk Inventor. This book continues by examining the different mechanisms commonly used in walking robots. You will learn the basic types of planar four-bar linkages commonly used in mechanical designs and how to use the GeoGebra Dynamic Geometry software to simulate and analyze 2D linkages. Using the knowledge you gained about linkages and mechanism, you will learn how to modify your robot and change its behavior by modifying or creating new parts. In the final chapter of this book you learn how to combine all the robot parts into assemblies and then run motion analysis. You will finish off your project by creating 3D animations of your robot in action. There are many books that show you how to perform individual tasks with Autodesk Inventor, but this book takes you through an entire project and shows you the complete engineering process. By the end of this book you will have modeled and assembled nearly all the parts that make up the TAMIYA® Mechanical Tiger and can start building your own robot.

Download or read book Learning Autodesk Inventor 2018 written by Randy Shih and published by SDC Publications. This book was released on 2017-07-19 with total page 512 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book will teach you everything you need to know to start using Autodesk Inventor 2018 with easy to understand, step-by-step tutorials. This book features a simple robot design used as a project throughout the book. You will learn to model parts, create assemblies, run simulations and even create animations of your robot design. An unassembled version of the same robot used throughout the book can be bundled with the book. No previous experience with Computer Aided Design(CAD) is needed since this book starts at an introductory level. The author begins by getting you familiar with the Inventor interface and its basic tools. You will start by learning to model simple robot parts and before long you will graduate to creating more complex parts and multi-view drawings. Along the way you will learn the fundamentals of parametric modeling through the use of geometric constraints and relationships. You will also become familiar with many of Inventor's powerful tools and commands that enable you to easily construct complex features in your models. Also included is coverage of gears, gear trains and spur gear creation using Autodesk Inventor. This book continues by examining the different mechanisms commonly used in walking robots. You will learn the basic types of planar four-bar linkages commonly used in mechanical designs and how to use the GeoGebra Dynamic Geometry software to simulate and analyze 2D linkages. Using the knowledge you gained about linkages and mechanism, you will learn how to modify your robot and change its behavior by modifying or creating new parts. In the final chapter of this book you learn how to combine all the robot parts into assemblies and then run motion analysis. You will finish off your project by creating 3D animations of your robot in action. There are many books that show you how to perform individual tasks with Autodesk Inventor, but this book takes you through an entire project and shows you the complete engineering process. By the end of this book you will have modeled and assembled nearly all the parts that make up the TAMIYA® Mechanical Tiger and can start building your own robot.

Download or read book The LEGO MINDSTORMS Robot Inventor Activity Book written by Daniele Benedettelli and published by No Starch Press. This book was released on 2021-09-21 with total page 250 pages. Available in PDF, EPUB and Kindle. Book excerpt: An introduction to the LEGO Mindstorms Robot Inventor Kit through seven engaging projects. With its amazing assortment of bricks, motors, and smart sensors, the LEGO® MINDSTORMS® Robot Inventor set opens the door to a physical-meets-digital world. The LEGO MINDSTORMS Robot Inventor Activity Book expands that world into an entire universe of incredibly fun, uniquely interactive robotic creations! Using the Robot Inventor set and a device that can run the companion app, you’ll learn how to build bots beyond your imagination—from a magical monster that gobbles up paper and answers written questions, to a remote-controlled transformer car that you can drive, steer, and shape-shift into a walking humanoid robot at the press of a button. Author and MINDSTORMS master Daniele Benedettelli, a robotics expert, takes a project-based approach as he leads you through an increasingly sophisticated collection of his most captivating robot models, chapter by chapter. Each project features illustrated step-by-step building instructions, as well as detailed explanations on programming your robots through the MINDSTORMS App—no coding experience required. As you build and program an adorable pet turtle, an electric guitar that lets you shred out solos, a fully functional, whiz-bang pinball machine and more, you’ll discover dozens of cool building and programming techniques to apply to your own LEGO creations, from working with gears and motors, to smoothing out sensor measurement errors, storing data in variables and lists, and beyond. By the end of this book, you’ll have all the tools, talent and inspiration you need to invent your own LEGO MINDSTORMS robots.

Download or read book Learning Autodesk Inventor 2020 written by Randy Shih and published by SDC Publications. This book was released on 2019-07 with total page 512 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book will teach you everything you need to know to start using Autodesk Inventor 2020 with easy to understand, step-by-step tutorials. This book features a simple robot design used as a project throughout the book. You will learn to model parts, create assemblies, run simulations and even create animations of your robot design. An unassembled version of the same robot used throughout the book can be bundled with the book. No previous experience with Computer Aided Design(CAD) is needed since this book starts at an introductory level. The author begins by getting you familiar with the Inventor interface and its basic tools. You will start by learning to model simple robot parts and before long you will graduate to creating more complex parts and multi-view drawings. Along the way you will learn the fundamentals of parametric modeling through the use of geometric constraints and relationships. You will also become familiar with many of Inventor's powerful tools and commands that enable you to easily construct complex features in your models. Also included is coverage of gears, gear trains and spur gear creation using Autodesk Inventor. This book continues by examining the different mechanisms commonly used in walking robots. You will learn the basic types of planar four-bar linkages commonly used in mechanical designs and how to use the GeoGebra Dynamic Geometry software to simulate and analyze 2D linkages. Using the knowledge you gained about linkages and mechanism, you will learn how to modify your robot and change its behavior by modifying or creating new parts. In the final chapter of this book you learn how to combine all the robot parts into assemblies and then run motion analysis. You will finish off your project by creating 3D animations of your robot in action. There are many books that show you how to perform individual tasks with Autodesk Inventor, but this book takes you through an entire project and shows you the complete engineering process. By the end of this book you will have modeled and assembled nearly all the parts that make up the TAMIYA® Mechanical Tiger and can start building your own robot.

Download or read book Smart Robotics with LEGO MINDSTORMS Robot Inventor written by Aaron Maurer and published by Packt Publishing Ltd. This book was released on 2021-05-07 with total page 438 pages. Available in PDF, EPUB and Kindle. Book excerpt: Discover how to use the LEGO MINDSTORMS Inventor kit and boost your confidence in robotics Key FeaturesGain confidence in building robots using creative designsLearn advanced robotic features and find out how to integrate them to build a robotWork with the block coding language used in robotics software in a practical wayBook Description LEGO MINDSTORMS Robot Inventor is the latest addition to the LEGO MINDSTORMS theme. It features unique designs that you can use to build robots, and also enable you to perform activities using the robot inventor application. You'll begin by exploring the history of LEGO MINDSTORMS, and then delve into various elements of the Inventor kit. Moving on, you'll start working on different projects which will prepare you to build a variety of smart robots. The first robotic project involves designing a claw to grab objects, and helps you to explore how a smart robot is used in everyday life and in industry. The second project revolves around building a working guitar that can be played and modified to meet the needs of the user. As you advance, you'll explore the concept of biomimicry as you discover how to build a scorpion robot. In addition to this, you'll also work on a classic robotic challenge by building a sumobot. Throughout the book, you'll come across a variety of projects that will provide you with hands-on experience in building creative robots, such as building a Dragster, Egg Decorator, and Plankton from Spongebob Squarepants. By the end of this LEGO book, you'll have got to grips with the concepts behind building a robot, and also found creative ways to integrate them using the application based on your creative insights and ideas. What you will learnDiscover how the Robot Inventor kit works, and explore its parts and the elements inside themDelve into the block coding language used to build robotsFind out how to create interactive robots with the help of sensorsUnderstand the importance of real-world robots in today's landscapeRecognize different ways to build new ideas based on existing solutionsDesign basic to advanced level robots using the Robot Inventor kitWho this book is for This book is for robot enthusiasts, LEGO lovers, hobbyists, educators, students, and anyone looking to learn about the new LEGO Robot Inventor kit. This book is designed to go beyond the basic build through to intermediate and advanced builds, and enables you to add your personal flair to the builds and codes.

Download or read book Tools for Design Using AutoCAD 2022 and Autodesk Inventor 2022 written by Randy Shih and published by SDC Publications. This book was released on 2021-07 with total page 644 pages. Available in PDF, EPUB and Kindle. Book excerpt: Tools for Design is intended to provide you with an overview of computer aided design using two popular CAD software packages from Autodesk: AutoCAD and Autodesk Inventor. This book explores the strengths of each package and shows how they can be used in design, both separately and in combination with each other. What you'll learn • How to create and dimension 2D multiview drawings using AutoCAD • How to freehand sketch using axonometric, oblique and perspective projection techniques • How to create 3D parametric models and 2D multiview drawings using Autodesk Inventor • How to reuse design information between AutoCAD and Autodesk Inventor • How to combine parts into assemblies including assembly modeling with a LEGO® MINDSTORMS® Education Base Set, with a TETRIX® kit and a VEX Robot Kit • How to perform basic finite element stress analysis using Inventor Stress Analysis Module Who this book is for This book is designed for high school and college age students wanting to learn the fundamentals of computer aided design with AutoCAD and Inventor and how the two can be used together. No prior CAD experience is required. Table of Contents Introduction: Getting Started 1. Fundamentals of AutoCAD 2. Basic Object Construction and Dynamic Input - AutoCAD 3. Geometric Construction and Editing Tools - AutoCAD 4. Orthographic Views in Multiview Drawings - AutoCAD 5. Basic Dimensioning and Notes - AutoCAD 6. Pictorials and Sketching 7. Parametric Modeling Fundamentals - Autodesk Inventor 8. Constructive Solid Geometry Concepts - Autodesk Inventor 9. Model History Tree - Autodesk Inventor 10. Parametric Constraints Fundamentals - Autodesk Inventor 11. Geometric Construction Tools - Autodesk Inventor 12. Parent/Child Relationships and the BORN Technique - Autodesk Inventor 13. Part Drawings and 3D Model-Based Definition - Autodesk Inventor 14. Symmetrical Features in Design - Autodesk Inventor 15. Design Reuse Using AutoCAD and Autodesk Inventor 16. Assembly Modeling - Putting It All Together - Autodesk Inventor 17. Design Analysis - Autodesk Inventor Stress Analysis Module

Download or read book STEM Education with Robotics written by Purvee Chauhan and published by Taylor & Francis. This book was released on 2023-05-11 with total page 261 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book offers a synthesis of research, curriculum examples, pedagogy models, and classroom recommendations for the effective use of robotics in STEM teaching and learning. Authors Chauhan and Kapila demonstrate how the use of educational robotics can catalyze and enhance student learning and understanding within the STEM disciplines. The book explores the implementation of design-based research (DBR); technological, pedagogical, and content knowledge (TPACK); and the 5E instructional model; among others. Chapters draw on a variety of pedagogical scaffolds to help teachers deploy educational robotics for classroom use, including research-driven case studies, strategies, and standards-aligned lesson plans from real-life settings. This book will benefit STEM teachers, STEM teacher educators, and STEM education researchers.