Download or read book Large Eddy Simulations of Motored Flow and Combustion in a Stratified Charge Direct Injection Spark Ignition Engine written by Samuel Kazmouz and published by . This book was released on 2020 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: Stratified-charge, spray-guided, spark-ignition, direct-injection operation offers efficiency improvements to conventional engines used in light-duty vehicles. However, cycle-to-cycle variability (CCV) impedes extracting the full efficiency potential of such advanced engine operation modes. In this dissertation, multi-cycle motored and fired large-eddy simulation (LES) results of an optically-accessible single-cylinder four-valve direct-injection spark- ignition engine, called G4VDI, are presented and compared to experimental results. The main objective is to investigate the root causes of CCV in stratified-charge engines. For motored operation, four sets of 60 consecutive LES cycles, with different operating conditions, are compared with experiments. LES is able to capture the wave dynamics of the ports and the in-cylinder pressure with a difference of 0.12%-2.5%, compared to experimental results. The LES velocity fields are compared with particle-image velocimetry measurements at six cutting planes. Based on the local and volume-averaged structure and magnitude indexes, it is found that LES is able to reproduce key flow events and capture large-scale in-cylinder flow structures, especially in high tumble/swirl conditions. Using proper orthogonal decomposition, LES shows that high tumble/swirl conditions produce low CCV flow fields. CCV of in-cylinder pressure ranged between 0.13% and 0.23%. For fired operation, and using the thickened flame model (TFM), 20 consecutive LES cycles of a homogeneous-charge engine operation mode are presented followed by spray-characterization in four different ambient conditions. These results lay the foundation for two stratified-charge engine operation modes, in which 20 and 35 consecutive LES cycles are compared with experiments, respectively. TFM-LES is extended for partially premixed flames and is able to reproduce experimental in-cylinder pressure (0.5%-10%), cyclic variability (20.5%-22.7%) in global and local quantities, local fuel vapor distributions, and heat release curves for homogeneous and stratified burn. Tuning TFM to reduce the burn rate increases the tendency to produce misfires, as well as the levels of CCV. Correlation analysis done on the stratified-charge LES results suggests that the influence of the early burn on the subsequent flame development is more subtle for stratified combustion compared to homogeneous combustion, that is the local conditions at the spark plug when the flame starts propagating are more influential than the conditions at spark timing, and that the injection event creates velocity conditions which might be favorable or unfavorable for the combustion event. The main contributions of this dissertation are extending TFM to highly stratified spray combustion, showing that LES can reproduce experimentally measured flow and combustion behavior in a realistic engine, including CCV, and analyzing LES to provide new insight into CCV and misfires of stratified-charge engines.

Download or read book Large Eddy Simulations of Motored Flow and Combustion in a Homogeneous Charge Spark Ignition Engine written by Yajuvendra Shekhawat and published by . This book was released on 2017 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: Cycle-to-cycle variations (CCV) of flow and combustion in internal combustion engines (ICE) limit their fuel efficiency and emissions potential. Large-eddy simulation (LES) is the most practical simulation tool to understand the nature of these CCV. In this research, multi-cycle LES of a two-valve, four-stroke, spark-ignition optical engine has been performed for motored and fired operations. The LES mesh quality is assessed using a length scale resolution parameter and a energy resolution parameter. For the motored operation, two 50-consecutive-cycle LES with different turbulence models (Smagorinsky model and dynamic structure model) are compared with the experiment. The pressure comparison shows that the LES is able to capture the wave-dynamics in the intake and exhaust ports. The LES velocity fields are compared with particle-image velocimetry (PIV) measurements at three cutting planes. Based on the structure and magnitude indices, the dynamic structure model is somewhat better than the Smagorinsky model as far asthe ensemble-averaged velocity fields are concerned. The CCV in the velocity fields is assessed by proper-orthogonal decomposition (POD). The POD analysis shows that LES is able to capture the level of CCV seen in the experiment. For the fired operation, two 60-cycle LES with different combustion models (thickened flame model and coherent flame model) are compared with experiment. The in-cylinderpressure and the apparent heat release rate comparison shows higher CCV for LES compared to the experiment, with the thickened flame model showing higher CCV than the coherent flame model. The correlation analysis for the LES using thickened flame model shows that the CCV in combustion/pressure is correlated with: the tumble at the intake valve closing, the resolved and subfilter-scale kinetic energy just before spark time, and the second POD mode (shear flow near spark gap) of the velocity fields just before spark time.

Download or read book Large eddy Simulations of Direct injection Spark ignition Engine Spray and Flow Variability written by and published by . This book was released on 2015 with total page 396 pages. Available in PDF, EPUB and Kindle. Book excerpt: Cycle-to-cycle variations (CCVs) in engines limit the ability of engine designers to reach the theoretical limits of engine efficiency. This study investigates CCVs in Direct-injection Spark-ignition (DISI) engines through Large-eddy Simulations (LES). Multi-cycle simulations of motored engine flow and spray simulations with variable boundary conditions were performed. The Dynamic Structure turbulence model, which is an advanced 1-equation non-viscosity turbulence model, was used to enable coarser, engineering type meshes and reasonable computational requirements. Multi-cycle motored engine simulations were run for an optical engine at several different engine operating conditions. Comparisons included both pressure and velocity measurements using Particle Image Velocimetry (PIV). Simulations were run using computational domains that either did or did not include intake and exhaust mixing plenums. Results from runners-only and full-domain simulations were overall similar, but there were differences in specific flow structures at certain times. Changes to engine speed or manifold pressure increased flow magnitudes, even after adjusting for different mean piston speeds, but had relatively minor effects on the flow structure. A spray model adapted from diesel spray simulations is presented. The adapted models were unable to match experimental trends with changing ambient density in both liquid and vapor phases simultaneously. Two spray break-up model parameters were changed to vary as functions of ambient density, which greatly improved the vapor predictions but worsened liquid predictions. Two methods from Uncertainty Quantification (UQ) were used to test the response of the spray models to prescribed uncertainty in spray boundary conditions. The effects of having uncertainty in two numerical model parameters and two physical boundary conditions was examined. Overall simulation uncertainty was much larger than the experimental uncertainty. Further tests showed the uncertainty in the simulation response variables was due primarily to uncertainty in the numerical modeling parameters. When examining the effects of uncertainty in the physical boundary conditions alone, the resulting variability in the response variables was approximately equal to the variability in the spray measurements.

Download or read book Modelling Spark Ignition Combustion written by P. A. Lakshminarayanan and published by Springer Nature. This book was released on with total page 678 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Flow and Combustion in Reciprocating Engines written by C. Arcoumanis and published by Springer Science & Business Media. This book was released on 2009-06-29 with total page 427 pages. Available in PDF, EPUB and Kindle. Book excerpt: Optimization of combustion processes in automotive engines is a key factor in reducing fuel consumption. This book, written by eminent university and industry researchers, investigates and describes flow and combustion processes in diesel and gasoline engines.

Download or read book Using Large Eddy Simulations to Study Diesel DI HCCI Engine Flow Structure Mixing and Combustion written by Rahul Jhavar and published by . This book was released on 2007 with total page 154 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Multi dimensional Modeling of Mixing and Combustion of Direct Injection Spark Ignition Engines written by Li Fan and published by . This book was released on 2000 with total page 214 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Spray Characterization in a Motored Direct injection Spark ignited Engine written by Scott Elmer Parrish and published by . This book was released on 1997 with total page 586 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Direct and Large Eddy Simulation X written by Dimokratis G.E. Grigoriadis and published by Springer. This book was released on 2017-10-06 with total page 523 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book addresses nearly all aspects of the state of the art in LES & DNS of turbulent flows, ranging from flows in biological systems and the environment to external aerodynamics, domestic and centralized energy production, combustion, propulsion as well as applications of industrial interest. Following the advances in increased computational power and efficiency, several contributions are devoted to LES & DNS of challenging applications, mainly in the area of turbomachinery, including flame modeling, combustion processes and aeroacoustics. The book includes work presented at the tenth Workshop on 'Direct and Large-Eddy Simulation' (DLES-10), which was hosted in Cyprus by the University of Cyprus, from May 27 to 29, 2015. The goal of the workshop was to establish a state of the art in DNS, LES and related techniques for the computation and modeling of turbulent and transitional flows. The book is of interest to scientists and engineers, both in the early stages of their career and at a more senior level.

Download or read book Test Stand Design for a High Compression Direct injection Spark ignition Methanol Fueled Engine and Results of Various Engine Configurations written by Steven Robert George and published by . This book was released on 2000 with total page 186 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book An Experimental Investigation of Direct Injection for Homogeneous and Fuel stratified Charge Compression Ignited Combustion Timing Control written by Craig David Marriott and published by . This book was released on 2001 with total page 664 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Stratified charge Operation of a Spark ignition Engine written by Lloyd Willard Jedeka and published by . This book was released on 1940 with total page 104 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Modelling Spark Ignition Combustion written by P. A. Lakshminarayanan and published by Springer. This book was released on 2024-05-02 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: The book provides a comprehensive overview of combustion models used in different types of spark ignition engines. In the first generation of spark ignition (SI) engines, the turbulence is created by the shear flow passing through the intake valves, and significantly decays during the intake and compression strokes. The residual turbulence enhances the laminar flame velocity, which is characteristic of the fuel and increases the relative effectiveness of the engine. In this simple two-zone model, the turbulence is estimated empirically; the spherical flame propagation model considers ignition delay, thermodynamics, heat transfer and chemical equilibrium, to obtain the performance and emissions of an SI engine. The model is used extensively by designers and research engineers to handle the fuel-air mixture prepared in the inlet and different geometries of open combustion chambers. The empiricism of the combustion model was progressively dismantled over the years. New 3D models for ignition considering the flow near a spark plug and flame propagation in the bulk gases were developed by incorporating solutions to Reynolds-averaged Navier-Stokes (RANS) equations for the turbulent flow with chemical reactions in the intense computational fluid dynamics. The models became far less empirical and enabled treating new generation direct-injection spark-ignition (DISI) gasoline and gas engines. The more complex layout of DISI engines with passive or active prechamber is successfully handled by them. This book presents details of models of SI engine combustion progressively increasing in complexity, making them accessible to designers, researchers, and even mechanical engineers who are curious to explore the field. This book is a valuable resource for anyone interested in spark ignition combustion.

Download or read book Direct and Large Eddy Simulation I written by Peter R. Voke and published by Springer Science & Business Media. This book was released on 1994-10-31 with total page 454 pages. Available in PDF, EPUB and Kindle. Book excerpt: It is a truism that turbulence is an unsolved problem, whether in scientific, engin eering or geophysical terms. It is strange that this remains largely the case even though we now know how to solve directly, with the help of sufficiently large and powerful computers, accurate approximations to the equations that govern tur bulent flows. The problem lies not with our numerical approximations but with the size of the computational task and the complexity of the solutions we gen erate, which match the complexity of real turbulence precisely in so far as the computations mimic the real flows. The fact that we can now solve some turbu lence in this limited sense is nevertheless an enormous step towards the goal of full understanding. Direct and large-eddy simulations are these numerical solutions of turbulence. They reproduce with remarkable fidelity the statistical, structural and dynamical properties of physical turbulent and transitional flows, though since the simula tions are necessarily time-dependent and three-dimensional they demand the most advanced computer resources at our disposal. The numerical techniques vary from accurate spectral methods and high-order finite differences to simple finite-volume algorithms derived on the principle of embedding fundamental conservation prop erties in the numerical operations. Genuine direct simulations resolve all the fluid motions fully, and require the highest practical accuracy in their numerical and temporal discretisation. Such simulations have the virtue of great fidelity when carried out carefully, and repre sent a most powerful tool for investigating the processes of transition to turbulence.

Download or read book Direct and Large Eddy Simulation XI written by Maria Vittoria Salvetti and published by Springer. This book was released on 2019-02-02 with total page 608 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book gathers the proceedings of the 11th workshop on Direct and Large Eddy Simulation (DLES), which was held in Pisa, Italy in May 2017. The event focused on modern techniques for simulating turbulent flows based on the partial or full resolution of the instantaneous turbulent flow structures, as Direct Numerical Simulation (DNS), Large-Eddy Simulation (LES) or hybrid models based on a combination of LES and RANS approaches. In light of the growing capacities of modern computers, these approaches have been gaining more and more interest over the years and will undoubtedly be developed and applied further. The workshop offered a unique opportunity to establish a state-of-the-art of DNS, LES and related techniques for the computation and modeling of turbulent and transitional flows and to discuss about recent advances and applications. This volume contains most of the contributed papers, which were submitted and further reviewed for publication. They cover advances in computational techniques, SGS modeling, boundary conditions, post-processing and data analysis, and applications in several fields, namely multiphase and reactive flows, convection and heat transfer, compressible flows, aerodynamics of airfoils and wings, bluff-body and separated flows, internal flows and wall turbulence and other complex flows.

Download or read book Large Eddy Simulation for Incompressible Flows written by P. Sagaut and published by Springer Science & Business Media. This book was released on 2006 with total page 600 pages. Available in PDF, EPUB and Kindle. Book excerpt: First concise textbook on Large-Eddy Simulation, a very important method in scientific computing and engineering From the foreword to the third edition written by Charles Meneveau: "... this meticulously assembled and significantly enlarged description of the many aspects of LES will be a most welcome addition to the bookshelves of scientists and engineers in fluid mechanics, LES practitioners, and students of turbulence in general."

Download or read book Direct and Large Eddy Simulation written by Bernard J. Geurts and published by Walter de Gruyter GmbH & Co KG. This book was released on 2022-12-05 with total page 320 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book presents a comprehensive overview of the mathematics and physics behind the simulation of turbulent flows and discusses in detail (i) the phenomenology of turbulence in fluid dynamics, (ii) the role of direct and large-eddy simulation in predicting these dynamics, (iii) the multiple considerations underpinning subgrid modelling, and, (iv) the issue of validation and reliability resulting from interacting modelling and numerical errors.