Download or read book Investigation of Foaming Behaviors in Injection Molding Using Mold Pressure Profile written by John Won S. Lee and published by . This book was released on 2009 with total page 466 pages. Available in PDF, EPUB and Kindle. Book excerpt: This thesis is intended to improve the understanding of foaming behaviors in various foam injection molding processes: structural foam molding, gas counter pressure molding, and gas counter pressure with mold opening. The foaming behavior in foam injection molding is different from foam extrusion in two ways. First, foaming occurs in a confined volume, which consists of a mold, whereas, it occurs in an open environment in foam extrusion. And second, while the foaming behavior in foam extrusion does not change with time once the steady state is reached, foam injection molding is on the other hand, time-dependent. These differences made it very challenging to study the foaming behaviors in foam injection molding. In this thesis, experiments were first conducted in foam extrusion to understand the effects of processing and material parameters on cell nucleation and growth behaviors. Subsequently, the knowledge obtained from the foam extrusion experiments was transferred to the foam injection molding process and the fundamental foaming mechanisms in foam injection molding were developed by conducting extensive experiments. Four processing parameters were mainly studied in this thesis: injection speed, void fraction setting (i.e., shot size), nitrogen content, and gate resistance. The experimental results revealed that the mold pressure profile during the foam injection molding process governed its foaming behaviors. Furthermore, by analyzing the mold pressure profile during the structural foam molding, it was possible to predict the achievable cell density in structural foam molding based on the foam extrusion results. When the gas counter pressure was employed, the analysis of the foaming behavior was relatively easier since the cell nucleation did not occur during the injection stage. However, the cell density that was achieved by using the gas counter pressure was generally lower than that obtained in structural foam molding due to the lower pressure drop rate caused by the use of the gas counter pressure. It was also discovered that the use of mold opening in combination with the gas counter pressure was very effective when uniform cell structure with a high void fraction was desired in addition to class-A surface quality.

Download or read book Quantitative Analysis of the Shrinkage and Warpage Behavior of Injection Molded Parts Using Conventional and Microcellular Injection Molding and Microcellular Co injection Molding written by Adam Jon Kramschuster and published by . This book was released on 2005 with total page 174 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Handbook of Polymeric Foams and Foam Technology written by Daniel Klempner and published by Hanser Gardner Publications. This book was released on 2004 with total page 584 pages. Available in PDF, EPUB and Kindle. Book excerpt: Describing all classes of polymeric foams, including their chemistry, synthesis, commercial production methods, properties, and applications, this handbook is designed to support engineers in their effort to develop practical solutions for industrial design and manufacturing challenges.

Download or read book Dissertation Abstracts International written by and published by . This book was released on 1978 with total page 674 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Some Critical Issues for Injection Molding written by Jian Wang and published by BoD – Books on Demand. This book was released on 2012-03-23 with total page 285 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book is composed of different chapters which are related to the subject of injection molding and written by leading international academic experts in the field. It contains introduction on polymer PVT measurements and two main application areas of polymer PVT data in injection molding, optimization for injection molding process, Powder Injection Molding which comprises Ceramic Injection Molding and Metal Injection Molding, ans some special techniques or applications in injection molding. It provides some clear presentation of injection molding process and equipment to direct people in plastics manufacturing to solve problems and avoid costly errors. With useful, fundamental information for knowing and optimizing the injection molding operation, the readers could gain some working knowledge of the injection molding.

Download or read book Advances in Design Simulation and Manufacturing VII written by Vitalii Ivanov and published by Springer Nature. This book was released on with total page 467 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Phenolic Based Foams written by Sandhya P.K and published by Springer Nature. This book was released on 2022-01-13 with total page 374 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book covers the latest developments in phenolic foams and their applications. Compared with polystyrene and polyurethane foams, phenolic foams are known as third-generation polymeric foams. Phenolic foams exhibit excellent fire-retardant properties, including low flammability, low peak heat release rate, no dripping during combustion, and low toxicity. This book discusses various aspects of phenolic foams including properties, synthesis, fabrication methodologies, and applications. The contents also cover the methods for toughening of phenolic foams to make them more widely applicable. This book is of interest to both academics and industry alike. It is also a useful reference for fire safety regulators and policy-makers looking for new materials and methods for sustainable fire protection.

Download or read book Polylactide Foams written by Mohammadreza Nofar and published by William Andrew. This book was released on 2017-09-18 with total page 274 pages. Available in PDF, EPUB and Kindle. Book excerpt: Polylactide Foams: Fundamentals, Manufacturing, and Applications provides an introduction to the fundamental science behind plastic foams, polylactic acid) and polylactide foaming, giving designers tactics to replace traditional resins with sustainable and biodegradable materials. The book then delves deeper into the technology behind PLA foaming, such as PLA/gas mixture characteristics, solubility, interfacial tension behaviors and crystallization kinetics of various types of PLA and their compounds. The foaming behaviors and mechanisms of various types of PLA and PLA compounds are extensively analyzed and discussed through different manufacturing technologies, namely extrusion foaming, foam injection molding and bead foaming. Interest in Poly(lactic acid) and PLA foams is extremely high – particularly as a potential replacement for styrenic resins – and the price of PLA resin is lower than ever before. This biopolymer has significant potential to improve the sustainability of the plastics industry. Polylactide Foams have a range of potential applications, such as in construction, packaging, insulation, biomedical scaffolds, and others. However, processing and performance of PLA are not at the same level as other non-biodegradable resins. Introduces the concepts behind foaming, poly(lactic acid) and PLA foaming Supports further research and development in PLA foams by covering the state-of-the-art in different manufacturing and processing methods Provides practical guidance for materials scientists and engineers in industry looking to replace traditional polymer resins with a sustainable, biodegradable alternative

Download or read book Microcellular Injection Molding written by Jingyi Xu and published by John Wiley & Sons. This book was released on 2011-01-06 with total page 503 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book presents the most important aspects of microcellular injection molding with applications for science and industry. The book includes: experimental rheology and pressure-volume-temperature (PVT) data for different gas materials at real injection molding conditions, new mathematical models, micrographs of rheological and thermodynamic phenomena, and the morphologies of microcellular foam made by injection molding. Further, the author proposes two stages of processing for microcellular injection molding, along with a methodology of systematic analysis for process optimization. This gives critical guidelines for quality and quantity analyses for processing and equipment design.

Download or read book Scientific and Technical Aerospace Reports written by and published by . This book was released on 1980 with total page 748 pages. Available in PDF, EPUB and Kindle. Book excerpt: Lists citations with abstracts for aerospace related reports obtained from world wide sources and announces documents that have recently been entered into the NASA Scientific and Technical Information Database.

Download or read book Polymer Processing written by Donald G. Baird and published by John Wiley & Sons. This book was released on 2014-03-24 with total page 422 pages. Available in PDF, EPUB and Kindle. Book excerpt: Fundamental concepts coupled with practical, step-by-step guidance With its emphasis on core principles, this text equips readers with the skills and knowledge to design the many processes needed to safely and successfully manufacture thermoplastic parts. The first half of the text sets forth the general theory and concepts underlying polymer processing, such as the viscoelastic response of polymeric fluids and diffusion and mass transfer. Next, the text explores specific practical aspects of polymer processing, including mixing, extrusion dies, and post-die processing. By addressing a broad range of design issues and methods, the authors demonstrate how to solve most common processing problems. This Second Edition of the highly acclaimed Polymer Processing has been thoroughly updated to reflect current polymer processing issues and practices. New areas of coverage include: Micro-injection molding to produce objects weighing a fraction of a gram, such as miniature gears and biomedical devices New chapter dedicated to the recycling of thermoplastics and the processing of renewable polymers Life-cycle assessment, a systematic method for determining whether recycling is appropriate and which form of recycling is optimal Rheology of polymers containing fibers Chapters feature problem sets, enabling readers to assess and reinforce their knowledge as they progress through the text. There are also special design problems throughout the text that reflect real-world polymer processing issues. A companion website features numerical subroutines as well as guidance for using MATLAB®, IMSL®, and Excel to solve the sample problems from the text. By providing both underlying theory and practical step-by-step guidance, Polymer Processing is recommended for students in chemical, mechanical, materials, and polymer engineering.

Download or read book Databook of Blowing and Auxiliary Agents written by George Wypych and published by Elsevier. This book was released on 2022-03-11 with total page 473 pages. Available in PDF, EPUB and Kindle. Book excerpt: Databook of Blowing and Auxiliary Agents, Second Edition includes the most current information on foaming technology, guiding users on the proper selection of formulation, which is highly dependent on the mechanisms of action of blowing agents and foaming agents, as well as dispersion and solubility. The book includes properties of 23 groups of blowing agents and the typical range of technical performance for each group, including general properties, physical-chemical properties, health and safety, environmental impact, and applications in different products and polymers. All information is illustrated by chemical reactions and diagrams. Chapters in the book look at foaming mechanisms with the use of solid blowing agents, which are decomposed to the gaseous products by application of heat, production of gaseous products by chemical reaction, and foaming by gases and evaporating liquids. Introduces the fundamental mechanisms of action of blowing agents and foaming Includes best practice guidance to help engineers and technicians improve the efficiency of their existing foaming processes Enables practitioners to select blowing agents and foaming methods more effectively, thus reducing the risk of poor specification Introduces useful analytical techniques for foaming Discusses the environmental impact of foaming processes

Download or read book Handbook of Foaming and Blowing Agents written by George Wypych and published by Elsevier. This book was released on 2022-03-12 with total page 309 pages. Available in PDF, EPUB and Kindle. Book excerpt: Handbook of Foaming and Blowing Agents, Second Edition includes the most current information on foaming technology, guiding users on the proper selection of formulation, which is highly dependent on the mechanisms of action of blowing agents and foaming agents, as well as dispersion and solubility. The book includes properties of 23 groups of blowing agents and the typical range of technical performance for each group, including general properties, physical-chemical properties, health and safety, environmental impact, and applications in different products and polymers. All information is illustrated by chemical reactions and diagrams. Chapters in the book look at foaming mechanisms with the use of solid blowing agents, which are decomposed to the gaseous products by application of heat, production of gaseous products by chemical reaction, and foaming by gases and evaporating liquids. Introduces the fundamental mechanisms of action of blowing agents and foaming Includes best practice guidance to help engineers and technicians improve the efficiency of their existing foaming processes Enables practitioners to select blowing agents and foaming methods more effectively, thus reducing the risk of poor specification Introduces useful analytical techniques for foaming Discusses the environmental impact of foaming processes

Download or read book Moldflow Design Guide written by Jay Shoemaker and published by . This book was released on 2006-01-01 with total page 326 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Applied Plastics Engineering Handbook written by Myer Kutz and published by William Andrew. This book was released on 2011-07-20 with total page 661 pages. Available in PDF, EPUB and Kindle. Book excerpt: A practical reference for all plastics engineers who are seeking to answer a question, solve a problem, reduce a cost, improve a design or fabrication process, or even venture into a new market. Applied Plastics Engineering Handbook covers both polymer basics – helpful to bring readers quickly up to speed if they are not familiar with a particular area of plastics processing – and recent developments – enabling practitioners to discover which options best fit their requirements. Each chapter is an authoritative source of practical advice for engineers, providing authoritative guidance from experts that will lead to cost savings and process improvements. Throughout the book, the focus is on the engineering aspects of producing and using plastics. The properties of plastics are explained along with techniques for testing, measuring, enhancing and analyzing them. Practical introductions to both core topics and new developments make this work equally valuable for newly qualified plastics engineers seeking the practical rules-of-thumb they don’t teach you in school, and experienced practitioners evaluating new technologies or getting up to speed on a new field The depth and detail of the coverage of new developments enables engineers and managers to gain knowledge of, and evaluate, new technologies and materials in key growth areas such as biomaterials and nanotechnology This highly practical handbook is set apart from other references in the field, being written by engineers for an audience of engineers and providing a wealth of real-world examples, best practice guidance and rules-of-thumb

Download or read book Powder Injection Molding written by Randall M. German and published by . This book was released on 2003 with total page 282 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Handbook of Polymer Crystallization written by Ewa Piorkowska and published by John Wiley & Sons. This book was released on 2013-07-01 with total page 514 pages. Available in PDF, EPUB and Kindle. Book excerpt: Polymeric crystals are more complex in nature than other materials' crystal structures due to significant structural disorder present. The only comprehensive reference on polymer crystallization, Handbook of Polymer Crystallization provides readers with a broad, in-depth guide on the subject, covering the numerous problems encountered during crystallization as well as solutions to resolve those problems to achieve the desired result. Edited by leading authorities in the field, topics explored include neat polymers, heterogeneous systems, polymer blends, polymer composites orientation induced crystallization, crystallization in nanocomposites, and crystallization in complex thermal processing conditions.