Download or read book Intelligent CAD Systems I written by Paul J.W. ten Hagen and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 366 pages. Available in PDF, EPUB and Kindle. Book excerpt: CAD (Computer Aided Design) technology is now crucial for every division of modern industry, from a viewpoint of higher productivity and better products. As technologies advance, the amount of information and knowledge that engineers have to deal with is constantly increasing. This results in seeking more advanced computer technology to achieve higher functionalities, flexibility, and efficient performance of the CAD systems. Knowledge engineering, or more broadly artificial intelligence, is considered a primary candidate technology to build a new generation of CAD systems. Since design is a very intellectual human activity, this approach seems to make sense. The ideas of intelligent CAD systems (ICAD) are now increasingly discussed everywhere. We can observe many conferences and workshops reporting a number of research efforts on this particular subject. Researchers are coming from computer science, artificial intelligence, mechanical engineering, electronic engineering, civil engineering, architectural science, control engineering, etc. But, still we cannot see the direction of this concept, or at least, there is no widely accepted concept of ICAD. What can designers expect from these future generation CAD systems? In which direction must developers proceed? The situation is somewhat confusing.
Download or read book Intelligent CAD Systems III written by Paul J.W. ten Hagen and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 268 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book contains a selection of revised versions of papers presented at the Third Eurographics Workshop on Intelligent CAD Systems, which was held at Hotel Opduin on the island of Texel in The Netherlands, April 3-7, 1989. The workshop theme was Practical Experience and Evaluation. It included five paper presentation sessions, each followed by a discussion. The workshop closed with a general discussion. The book is therefore divided into five parts: design process, system architecture, languages, geometric reasoning, and user interface. A report on the discussion session, written by the session's moderator, concludes each part. These reports are not intended to be exact records of the discussion, but rather the moderators' summary of their contents. The aim of the workshop was to share the experience the participants gained by developing intelligent CAD (Computer Aided Design) systems, and to evaluate the developed systems to determine which features were still lacking. The workshop was organized as the last one in a series of three workshops under the same title. The first workshop focused on theoretical and methodological aspects, resulting in a sound theoretical basis for intelligent CAD systems. Implementational issues were discussed at the second workshop, paying attention to systems developed with reference to this basis. The experience and evaluation showed a dual outcome. Firstly, it resulted in the development of a new generation of intelligent CAD systems. Secondly, it led us to the development of new theories for intelligent CAD.
Download or read book Intelligent CAD Systems I written by Paul J.W. ten Hagen and published by Springer. This book was released on 1987-12-30 with total page 360 pages. Available in PDF, EPUB and Kindle. Book excerpt: CAD (Computer Aided Design) technology is now crucial for every division of modern industry, from a viewpoint of higher productivity and better products. As technologies advance, the amount of information and knowledge that engineers have to deal with is constantly increasing. This results in seeking more advanced computer technology to achieve higher functionalities, flexibility, and efficient performance of the CAD systems. Knowledge engineering, or more broadly artificial intelligence, is considered a primary candidate technology to build a new generation of CAD systems. Since design is a very intellectual human activity, this approach seems to make sense. The ideas of intelligent CAD systems (ICAD) are now increasingly discussed everywhere. We can observe many conferences and workshops reporting a number of research efforts on this particular subject. Researchers are coming from computer science, artificial intelligence, mechanical engineering, electronic engineering, civil engineering, architectural science, control engineering, etc. But, still we cannot see the direction of this concept, or at least, there is no widely accepted concept of ICAD. What can designers expect from these future generation CAD systems? In which direction must developers proceed? The situation is somewhat confusing.
Download or read book Intelligent CAD Systems II written by Varol Akman and published by Springer Science & Business Media. This book was released on 1989-06-22 with total page 342 pages. Available in PDF, EPUB and Kindle. Book excerpt: Records of the 2nd Eurographics Workshop on "Intelligent CAD Systems", Held on April 19-23, 1988, at Konigshof Congress Centre, Veldhoven, the Netherlands
Download or read book Intelligent CAD Systems I written by Paul J W Ten Hagen and published by . This book was released on 1987-12-30 with total page 376 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Intelligent CAD written by Hiroyuki Yoshikawa and published by North Holland. This book was released on 1989 with total page 264 pages. Available in PDF, EPUB and Kindle. Book excerpt: Current CAD (Computer-Aided Design) systems, as used in many industries, are able to manipulate geometrical shapes very successfully. However, some would say that CAD means Computer-Aided Drawing'', i.e. CAD is only a very sophisticated drawing board, never intended to assist the thought processes of the designer. Automated design systems do exist, but these are limited to specific products with only a few varying parameters. This book deals with Intelligent CAD'', the concept of a system that could assist designers throughout the design process, deal with any object, and be connected to any other information processing system, such as CAM. The research papers collected here are from designers, and from researchers in Artificial Intelligence and Computer Science.
Download or read book Artificial Intelligence in Design written by D.T. Pham and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 499 pages. Available in PDF, EPUB and Kindle. Book excerpt: Computers have been employed for some time in engineering design mainly as numerical or graphical tools to assist analysis and draughting. The advent of the technology of artificial intelligence and expert systems has enabled computers to be applied to less deterministic design tasks which require symbolic manipulation and reasoning, instead of only routine number processing. This book presents recent examples of such applications, focusing on mechanical and manufacturing design. The term 'design' is interpreted here in its wider sense to include creative activities such as planning. The book covers a wide spectrum of design operations ranging from component and product design through to process, tooling and systems design. Its aim is to expose researchers, engineers and engineering designers to several developments in the emerging field of intelligent CAD and to alert them of the possibilites and opportunities in this exciting field.
Download or read book Developing Expert CAD Systems written by V. Begg and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 117 pages. Available in PDF, EPUB and Kindle. Book excerpt: The importance of CAD to electronics technology Computer-aided design (CAD) is one way of coping with the problem of how to design and build very complex systems. This problem is particularly acute in electronics technology. Designs are now (1984) said to be design-limited, rather than technology-limited. It can take months to generate a design for a chip, so that it might be obsolete before it can be manufactured. Manual design of large-scale integration (LSI) chips (circa 10,000 gates) is almost impossible. However, using current technology it is possible to produce chips having 250,000 gates. It is understandable, therefore, that there is great interest in improving existing CAD systems. Designers of CAD systems are concerned with formalizing and automating as much of the design task as possible. Automating design of any kind has long been acknowledged as a project fraught with intractable problems. A human designer has to have an understanding of the nature of the materials used in manufacture, a knowledge of common problems and well-tried solutions, and above all, creativity in producing new designs. Understanding, knowledge and creativity are three properties even the most artificially intelligent of computer programs have been entirely lacking in until very recently. Some people would deny computers these qualities entirely, on philosophical grounds (eg Dreyfus 1979; Searle 1981). There are few theories in cognitive psychology which can help.
Download or read book Intelligent Systems in Design and Manufacturing written by Cihan H. Dagli and published by American Society of Mechanical Engineers. This book was released on 1994 with total page 512 pages. Available in PDF, EPUB and Kindle. Book excerpt: Focuses on solutions to problems in design and manufacturing engineering, presenting a variety of problem solving approaches and practical examples. Covers neural networks and other artificial intelligence tools, computational models for conceptual design, desirable functionalities of intelligent CA
Download or read book Knowledge Intensive CAD written by Martti Mäntylä and published by Springer. This book was released on 2016-01-09 with total page 338 pages. Available in PDF, EPUB and Kindle. Book excerpt: Knowledge-Intensive CAD clarifies and elaborates the concepts of knowledge-intensive design and CAD. In today's advanced manufacturing environment, CAD systems should not only assist designers and engineers during product design, but also in design information for use in later stages of the process such as production, distribution and operation. This book focuses on the sharing of knowledge across life-cycle stages and organizational boundaries.
Download or read book Applications of Artificial Intelligence in Engineering VI written by George Rzevski and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 1017 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book contains papers presented at the sixth International Conference on Application of Artificial Intelligence in Engineering held in Oxford, UK in was held in Southampton, UK July 1991. The first conference in this series the second in Cambridge, Massachusetts, USA in 1987, the third in 1986, 1989 in Palo Alto, California, USA in 1988, the fourth in Cambridge, UK in and the fifth in Boston, Massachusetts, USA in 1990. The conference series has now established itself as the unique forum for the presentation of the latest research, development and application of artificial intelligence (AI) in all fields of engineering. Consequently, books of conference proceedings provide a historical record of the application of AI in engineering design, analysis, simulation, planning, scheduling, monitoring, control, diagnosis, reliability and quality, as well as in robotics and manufacturing systems, from the early beginnings to mature applications of today. Whilst previously the field was dominated by knowledge-based systems, in this latest volume, for the first time, a significant proportion of papers cover the paradigms of neural networks and genetic algorithms. Learning and self organising behaviour of systems based on these paradigms are particularly important in engineering applications. From a large number of submitted proposals over sixty papers have been selected by members of the Advisory Committee who acted as referees. Pa pers have been grouped under the following headings.
Download or read book Multi Agent Systems for Concurrent Intelligent Design and Manufacturing written by Weiming Shen and published by CRC Press. This book was released on 2019-09-17 with total page 415 pages. Available in PDF, EPUB and Kindle. Book excerpt: Agent Technology, or Agent-Based Approaches, is a new paradigm for developing software applications. It has been hailed as 'the next significant breakthrough in software development', and 'the new revolution in software' after object technology or object-oriented programming. In this context, an agent is a computer system which is capable of act
Download or read book Intelligent CAD III written by Hiroyuki Yoshikawa and published by North Holland. This book was released on 1991 with total page 372 pages. Available in PDF, EPUB and Kindle. Book excerpt: Design is at least as much a process of discovery as it is a purposeful manipulation of facts into a contemplated solution. Although the aspect of design which involves discovery can perhaps never be fully automated, we can expect to build systems to aid or to automate various problem solving aspects of design. The concept of an intelligent CAD system as the computer side of an effective human-computer team working on a design problem is by now well established. Such a team should relieve human designers from the routine and more mundane tasks encountered in the course of a design, allowing them to concentrate on more creative aspects. A conventional CAD system merely documents the outcome of a design, while an intelligent CAD system makes a meaningful contribution to the actual progress of a design. This volume contains the results of the IFIP workshop on intelligent CAD. Included are reports from the chairpersons of the three subgroups and plenary sessions, invited papers, and papers selected from contributions. The selected papers were first reviewed by the program committee and chairpersons and then revised based on their comments.Together with the proceedings from the previous two workshops, this volume contains an exhaustive documentation of the development of intelligent CAD.
Download or read book Advances in Computer Graphics written by Gerald Garcia and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 451 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book is a collection of several tutorials from the EUROGRAPHICS '90 conference in Montreux. The conference was held under the motto "IMAGES: Synthesis, Analysis and Interaction", and the tutorials, partly presented in this volume, reflect the conference theme. As such, this volume provides a unique collection of advanced texts on 'traditional' com puter graphics as well as of tutorials on image processing and image reconstruction. As with all the volumes of the series "Advances in Computer Graphics", the contributors are leading experts in their respective fields. The chapter Design and Display of Solid Models provides an extended introduction to interactive graphics techniques for design, fast display, and high-quality rendering of solid models. The text focuses on techniques for Constructive Solid Geometry (CSG). The follow ing topics are treated in depth: interactive design techniques (specification of curves, surfaces and solids; graphical user interfaces; procedural languages and direct manipulation) and display techniques (depth-buffer, scan-line and ray-tracing techniques; CSG classification techniques; efficiency-improving methods; software and hardware implementations).
Download or read book Advances in Production Management Systems written by E. Eloranta and published by Elsevier. This book was released on 2012-12-02 with total page 602 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book is divided into four sections: invited papers, principles, systems and techniques. The invited papers form an extensive overview of the state-of-the-art of production management. The themes range from the everlasting hunt for better productivity to the implications of CIM architectures (particularly CIM-OSA) for production management. The other three sections of the book look at the various problems affecting production management. One of the characteristics of modern production management is the need for better principles, systems and techniques for interorganizational production management. Another topic of crucial relevance is the necessity to master not only repetitive manufacturing but also one-of-a-kind product manufacturing. From the managerial point of view, the forecast-based make-to-stock principles have proven insufficient, with market forces demanding fast and reliable deliveries of customer-oriented products. The goals of production management have been re-evaluated as a result.
Download or read book CAD Systems Using AI Techniques written by Gōtarō Odawara and published by North Holland. This book was released on 1989 with total page 252 pages. Available in PDF, EPUB and Kindle. Book excerpt: Recent advances in VLSI technologies have allowed larger and more complex designs. CAD systems using Artificial Intelligence (AI) techniques play the most important role in their short-term realization. This book contains 27 research papers reporting on the various technical fields in VLSI CAD. It is a coordinated collection of papers from researchers in the USA, Europe and Japan. The main topics covered are logic design using AI techniques, and expert systems, every paper offering an effective solution applying AI techniques to difficult problems in the CAD field.
Download or read book Human Aspects in Computer Integrated Manufacturing written by G.J. Olling and published by Elsevier. This book was released on 2013-10-22 with total page 938 pages. Available in PDF, EPUB and Kindle. Book excerpt: The papers in this volume reflect the current research and development of advanced manufacturing software. They may be categorized as follows: New Concepts towards CIM, Product Realization through Product/Process Modelling, Intelligent Management and Control of Manufacturing Activities, and Development of CIM Systems.
