Download or read book Integrated Video Frequency Continuous Time Filters written by Scott D. Willingham and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 266 pages. Available in PDF, EPUB and Kindle. Book excerpt: Advances in the state of the art mean the signal processing ICs of ever-increasing complexity are being introduced. While the typical portion of a large IC devoted to analog circuits has diminished, the performance of those surviving analog signal processing circuits remains vital and their design challenging. Moreover, the emerging high-definition TV technology has created a new area for IC development, one with formidable signal processing requirements. The antialiasing filters needed for one proposed HDTV decoder motivated the research documented in this book. Sharply selective filters place tight constraints on the permitted excess phase shifts of their constituent circuits. Combined with stringent requirements for low distortion at video frequencies, these constraints challenge the IC filter designer. Integrated Video-Frequency Continuous-Time Filters: High-Performance Realizations in BiCMOS deals with what is arguably the mainstay of analog signal processing circuits. Prominent applications in computer disk-drive read channels, video receivers, rf circuits, and antialiasing and reconstruction in data converters testifies to their importance. Moreover, they are excellent benchmarks for more general analog signal processors. Bipolar and MOSFET transistors, freely combined at the lowest circuit levels, provide the designer with an opportunity to develop potent variations on the standard idioms. The book considers the general principles of BiCMOS circuit design, through to a demanding design problem. This case-study approach allows a concrete discussion of the justification for and practical trade-offs of each design decision. Audience: A reference work for experienced IC designers and a text for advanced IC design students.

Download or read book Continuous Time Low Pass Filters for Integrated Wideband Radio Receivers written by Ville Saari and published by Springer Science & Business Media. This book was released on 2012-03-15 with total page 207 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book presents a new filter design approach and concentrates on the circuit techniques that can be utilized when designing continuous-time low-pass filters in modern ultra-deep-submicron CMOS technologies for integrated wideband radio receivers. Coverage includes system-level issues related to the design and implementation of a complete single-chip radio receiver and related to the design and implementation of a filter circuit as a part of a complete single-chip radio receiver. Presents a new filter design approach, emphasizing low-voltage circuit solutions that can be implemented in modern, ultra-deep-submicron CMOS technologies;Includes filter circuit implementations designed as a part of a single-chip radio receiver in modern 1.2V 0.13um and 65nm CMOS;Describes design and implementation of a continuous-time low-pass filter for a multicarrier WCDMA base-station;Emphasizes system-level considerations throughout.

Download or read book High Frequency Continuous Time Filters in Digital CMOS Processes written by Shanthi Pavan and published by Springer Science & Business Media. This book was released on 2007-05-08 with total page 228 pages. Available in PDF, EPUB and Kindle. Book excerpt: There is an ever increasing trend towards putting entire systems on a single chip. This means that analog circuits will have to coexist on the same substrate along with massive digital systems. Since technologies are optimized with these digital systems in mind, designers will have to make do with standard CMOS processes in the years to come. We address analog filter design from this perspective. Filters form important blocks in applications ranging from computer disc-drive chips to radio transceivers. In this book, we develop the theory and techniques necessary for the implementation of high frequency (hundreds of megahertz) programmable continuous time filters in standard CMOS processes. Since high density poly-poly capacitors are not available in these technologies, alternative capacitor structures have to be found. Met- metal capacitors have low specific capacitance. An alternative is to use the (inherently nonlinear) capacitance formed by MOSFET gates. In Chapter 2, we focus on the use of MOS capacitors as integrating elements. A physics-based model which predicts distortion accurately is presented for a two-terminal MOS structure in accumulation. Distortion in these capacitors as a function of signal swing and bias voltage is computed. Chapter 3 reviews continuous-time filter architectures in the light of bias-dependent integrating capacitors. We also discuss the merits and demerits of various CMOS transconductance elements. The problems encountered in designing high frequency programmable filters are discussed in detail.

Download or read book Design of High Frequency Integrated Analogue Filters written by Yichuang Sun and published by IET. This book was released on 2002-04-15 with total page 258 pages. Available in PDF, EPUB and Kindle. Book excerpt: Sun (communication electronics, U. of Hertfordshire, UK), this volume's editor, also contributed a chapter on the architectures and design of OTA/gm-C filters. The other papers describe on-chip automatic tuning of filters, analog adaptive filters, low voltage techniques for switched-current filters, log domain filters, the MOSFET-C technique and active filters using integrated inductors. The contributors teach electrical engineering in the US, the UK, Thailand, and Canada. Annotation copyrighted by Book News, Inc., Portland, OR

Download or read book Continuous Time Delta Sigma Modulators for High Speed A D Conversion written by James A. Cherry and published by Springer Science & Business Media. This book was released on 2006-04-18 with total page 272 pages. Available in PDF, EPUB and Kindle. Book excerpt: Among analog-to-digital converters, the delta-sigma modulator has cornered the market on high to very high resolution converters at moderate speeds, with typical applications such as digital audio and instrumentation. Interest has recently increased in delta-sigma circuits built with a continuous-time loop filter rather than the more common switched-capacitor approach. Continuous-time delta-sigma modulators offer less noisy virtual ground nodes at the input, inherent protection against signal aliasing, and the potential to use a physical rather than an electrical integrator in the first stage for novel applications like accelerometers and magnetic flux sensors. More significantly, they relax settling time restrictions so that modulator clock rates can be raised. This opens the possibility of wideband (1 MHz or more) converters, possibly for use in radio applications at an intermediate frequency so that one or more stages of mixing might be done in the digital domain. Continuous-Time Delta-Sigma Modulators for High-Speed A/D Conversion: Theory, Practice and Fundamental Performance Limits covers all aspects of continuous-time delta-sigma modulator design, with particular emphasis on design for high clock speeds. The authors explain the ideal design of such modulators in terms of the well-understood discrete-time modulator design problem and provide design examples in Matlab. They also cover commonly-encountered non-idealities in continuous-time modulators and how they degrade performance, plus a wealth of material on the main problems (feedback path delays, clock jitter, and quantizer metastability) in very high-speed designs and how to avoid them. They also give a concrete design procedure for a real high-speed circuit which illustrates the tradeoffs in the selection of key parameters. Detailed circuit diagrams, simulation results and test results for an integrated continuous-time 4 GHz band-pass modulator for A/D conversion of 1 GHz analog signals are also presented. Continuous-Time Delta-Sigma Modulators for High-Speed A/D Conversion: Theory, Practice and Fundamental Performance Limits concludes with some promising modulator architectures and a list of the challenges that remain in this exciting field.

Download or read book VLSI Integrated Systems on Silicon written by Ricardo A. Reis and published by Springer. This book was released on 2013-06-05 with total page 569 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book contains the papers that have been presented at the ninth Very Large Scale Integrated Systems conference VLSI'97 that is organized biannually by IFIP Working Group 10.5. It took place at Hotel Serra Azul, in Gramado Brazil from 26-30 August 1997. Previous conferences have taken place in Edinburgh, Trondheim, Vancouver, Munich, Grenoble and Tokyo. The papers in this book report on all aspects of importance to the design of the current and future integrated systems. The current trend towards the realization of versatile Systems-on-a-Chip require attention of embedded hardware/software systems, dedicated ASIC hardware, sensors and actuators, mixed analog/digital design, video and image processing, low power battery operation and wireless communication. The papers as presented in Jhis book have been organized in two tracks, where one is dealing with VLSI System Design and Applications and the other presents VLSI Design Methods and CAD. The following topics are addressed: VLSI System Design and Applications Track • VLSI for Video and Image Processing. • Microsystem and Mixed-mode design. • Communication And Memory System Design • Cow-voltage & Low-power Analog Circuits. • High Speed Circuit Techniques • Application Specific DSP Architectures. VLSI Design Methods and CAD Track • Specification and Simulation at System Level. • Synthesis and Technology Mapping. • CAD Techniques for Low-Power Design. • Physical Design Issues in Sub-micron Technologies. • Architectural Design and Synthesis. • Testing in Complex Mixed Analog and Digital Systems.

Download or read book Low Voltage Low Power Analog Integrated Circuits written by Wouter A. Serdijn and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 117 pages. Available in PDF, EPUB and Kindle. Book excerpt: Low-Voltage Low-Power Analog Integrated Circuits brings together in one place important contributions and state-of-the-art research results in this rapidly advancing area. Low-Voltage Low-Power Analog Integrated Circuits serves as an excellent reference, providing insight into some of the most important issues in the field.

Download or read book Symbolic Analysis in Analog Integrated Circuit Design written by Henrik Floberg and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 171 pages. Available in PDF, EPUB and Kindle. Book excerpt: Symbolic Analysis in Analog Integrated Circuit Design provides an introduction to computer-aided circuit analysis and presents systematic methods for solving linear (i.e. small-signal) and nonlinear circuit problems, which are illustrated by concrete examples. Computer-aided symbolic circuit analysis is useful in analog integrated circuit design. Analytic expressions for the network transfer functions contain information that is not provided by a numerical simulation result. However, these expressions are generally extremely long and difficult to interpret; therefore, it is necessary to be able to approximate them guided by the magnitude of the individual circuit parameters. Engineering has been described as `the art of making approximations'. The inclusion of symbolic analysis in analog circuit design reduces the implied risk of ambiguity during the approximation process. A systematic method based on the nullor concept is used to obtain the basic feedback transistor amplifier configurations. Approximate expressions for the locations of poles and zeros for linear networks are obtained using the extended pole-splitting technique. An unusual feature in Symbolic Analysis in Analog Integrated Circuit Design is the consistent use of the transadmittance element with finite (linear or nonlinear) or infinite (i.e. nullor) gain as the only requisite circuit element. The describing function method is used to obtain approximate symbolic expressions for the harmonic distortion generated by a soft or hard transconductance nonlinearity embedded in an arbitrary linear network. The design and implementation of a program (i.e. CASCA) for symbolic analysis of time-continuous networks is described. The algorithms can also be used to solve other linear problems, e.g. the analysis of time-discrete switched-capacitor networks. Symbolic Analysis in Analog Integrated Circuit Design serves as an excellent resource for students and researchers as well as for industry designers who want to familiarize themselves with circuit analysis. This book may also be used for advanced courses on the subject.

Download or read book Distortion Analysis of Analog Integrated Circuits written by Piet Wambacq and published by Springer Science & Business Media. This book was released on 2013-04-17 with total page 528 pages. Available in PDF, EPUB and Kindle. Book excerpt: The analysis and prediction of nonlinear behavior in electronic circuits has long been a topic of concern for analog circuit designers. The recent explosion of interest in portable electronics such as cellular telephones, cordless telephones and other applications has served to reinforce the importance of these issues. The need now often arises to predict and optimize the distortion performance of diverse electronic circuit configurations operating in the gigahertz frequency range, where nonlinear reactive effects often dominate. However, there have historically been few sources available from which design engineers could obtain information on analysis tech niques suitable for tackling these important problems. I am sure that the analog circuit design community will thus welcome this work by Dr. Wambacq and Professor Sansen as a major contribution to the analog circuit design literature in the area of distortion analysis of electronic circuits. I am personally looking forward to hav ing a copy readily available for reference when designing integrated circuits for communication systems.

Download or read book Highly Linear Integrated Wideband Amplifiers written by Henrik Sjöland and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 171 pages. Available in PDF, EPUB and Kindle. Book excerpt: Highly Linear Integrated Wideband Amplifiers: Design and Analysis Techniques for Frequencies from Audio to RF deals with the complicated issues involved in the design of high-linearity integrated wideband amplifiers for different operating frequencies. The book demonstrates these principles using a number of high-performance designs. New topologies for high linearity are presented, as well as a novel method for estimating the intermodulation distortion of a wideband signal. One of the most exciting results presented is an enhanced feedback configuration called feedback boosting that is capable of very low distortion. Also important is a statistical method for relating the intermodulation distortion of a wideband signal to the total harmonic distortion (THD) of a single tone. The THD, as opposed to the intermodulation distortion of the wideband signal, is easy to measure and use as a design parameter. Three different applications where high linearity is needed are identified, namely audio power amplifiers, wideband IF amplifiers and RF power amplifiers. For these applications high-performance integrated amplifier designs using novel topologies are presented together with measurement results. The audio amplifiers are built in CMOS and are capable of driving 8Omega loudspeaker loads directly without using any external components. One of the designs can operate on a supply voltage down to 1.5V. Both bipolar and CMOS wideband IF amplifiers are built; they are fully differential and have linearity from DC to 20 MHz. Finally, an RF power amplifier is built in CMOS, without using inductors, in order to investigate what performance can be achieved without them. Highly Linear Integrated Wideband Amplifiers: Design and Analysis Techniques for Frequencies from Audio to RF is an excellent reference for researchers and designers of integrated amplifiers, and may be used as a text for advanced courses on the topic.

Download or read book CMOS Telecom Data Converters written by Angel Rodríguez-Vázquez and published by Springer Science & Business Media. This book was released on 2013-03-09 with total page 610 pages. Available in PDF, EPUB and Kindle. Book excerpt: CMOS Telecom Data Converters compiles the latest achievements regarding the design of high-speed and high-resolution data converters in deep submicron CMOS technologies. The four types of analog-to-digital converter architectures commonly found in this arena are covered, namely sigma-delta, pipeline, folding/interpolating and flash. For all these types, latest achievements regarding the solution of critical architectural and circuital issues are presented, and illustrated through IC prototypes with measured state-of-the-art performances. Some of these prototypes are conceived to be employed at the chipset of newest generation wireline modems (ADSL and ADSL+). Others are intended for wireless transceivers. Besides analog-to-digital converters, the book also covers other functions needed for communication systems, such as digital-to-analog converters, analog filters, programmable gain amplifiers, digital filters, and line drivers.

Download or read book Top Down Design of High Performance Sigma Delta Modulators written by Fernando Medeiro and published by Springer Science & Business Media. This book was released on 2013-04-18 with total page 303 pages. Available in PDF, EPUB and Kindle. Book excerpt: The interest for :I:~ modulation-based NO converters has significantly increased in the last years. The reason for that is twofold. On the one hand, unlike other converters that need accurate building blocks to obtain high res olution, :I:~ converters show low sensitivity to the imperfections of their building blocks. This is achieved through extensive use of digital signal pro cessing - a desirable feature regarding the implementation of NO interfaces in mainstream CMOS technologies which are better suited for implementing fast, dense, digital circuits than accurate analog circuits. On the other hand, the number of applications with industrial interest has also grown. In fact, starting from the earliest in the audio band, today we can find :I:~ converters in a large variety of NO interfaces, ranging from instrumentation to commu nications. These advances have been supported by a number of research works that have lead to a considerably large amount of published papers and books cov ering different sub-topics: from purely theoretical aspects to architecture and circuit optimization. However, so much material is often difficultly digested by those unexperienced designers who have been committed to developing a :I:~ converter, mainly because there is a lack of methodology. In our view, a clear methodology is necessary in :I:~ modulator design because all related tasks are rather hard.

Download or read book Integrated Video Frequency Continuous Time Filters written by Scott D. Willingham and published by Springer. This book was released on 2012-10-06 with total page 249 pages. Available in PDF, EPUB and Kindle. Book excerpt: Advances in the state of the art mean the signal processing ICs of ever-increasing complexity are being introduced. While the typical portion of a large IC devoted to analog circuits has diminished, the performance of those surviving analog signal processing circuits remains vital and their design challenging. Moreover, the emerging high-definition TV technology has created a new area for IC development, one with formidable signal processing requirements. The antialiasing filters needed for one proposed HDTV decoder motivated the research documented in this book. Sharply selective filters place tight constraints on the permitted excess phase shifts of their constituent circuits. Combined with stringent requirements for low distortion at video frequencies, these constraints challenge the IC filter designer. Integrated Video-Frequency Continuous-Time Filters: High-Performance Realizations in BiCMOS deals with what is arguably the mainstay of analog signal processing circuits. Prominent applications in computer disk-drive read channels, video receivers, rf circuits, and antialiasing and reconstruction in data converters testifies to their importance. Moreover, they are excellent benchmarks for more general analog signal processors. Bipolar and MOSFET transistors, freely combined at the lowest circuit levels, provide the designer with an opportunity to develop potent variations on the standard idioms. The book considers the general principles of BiCMOS circuit design, through to a demanding design problem. This case-study approach allows a concrete discussion of the justification for and practical trade-offs of each design decision. Audience: A reference work for experienced IC designers and a text for advanced IC design students.

Download or read book Compact Low Voltage and High Speed CMOS BiCMOS and Bipolar Operational Amplifiers written by Klaas-Jan de Langen and published by Springer Science & Business Media. This book was released on 2013-03-14 with total page 258 pages. Available in PDF, EPUB and Kindle. Book excerpt: Compact Low-Voltage and High-Speed CMOS, BiCMOS and Bipolar Operational Amplifiers discusses the design of integrated operational amplifiers that approach the limits of low supply voltage or very high bandwidth. The resulting realizations span the whole field of applications from micro-power CMOS VLSI amplifiers to 1-GHz bipolar amplifiers. The book presents efficient circuit topologies in order to combine high performance with simple solutions. In total twelve amplifier realizations are discussed. Two bipolar amplifiers are discussed, a 1-GHz operational amplifier and an amplifier with a high ratio between the maximum output current and the quiescent current. Five amplifiers have been designed in CMOS technology, extremely compact circuits that can operate on supply voltages down to one gate-source voltage and two saturation voltages which equals about 1.4 V and, ultimate-low-voltage amplifiers that can operate on supply voltages down to one gate-source voltage and one saturation voltage which amounts to about 1.2 V. In BiCMOS technology five amplifiers have been designed. The first two amplifiers are based on a compact topology. Two other amplifiers are designed to operate on low supply voltages down to 1.3 V. The final amplifier has a unity-gain frequency of 200 MHz and can operate down to 2.5 V. Compact Low-Voltage and High-Speed CMOS, BiCMOS and Bipolar Operational Amplifiers is intended for the professional analog designer. Also, it is suitable as a text book for advanced courses in amplifier design.

Download or read book Neuromorphic Systems Engineering written by Tor Sverre Lande and published by Springer. This book was released on 2007-08-26 with total page 462 pages. Available in PDF, EPUB and Kindle. Book excerpt: Neuromorphic Systems Engineering: Neural Networks in Silicon emphasizes three important aspects of this exciting new research field. The term neuromorphic expresses relations to computational models found in biological neural systems, which are used as inspiration for building large electronic systems in silicon. By adequate engineering, these silicon systems are made useful to mankind. Neuromorphic Systems Engineering: Neural Networks in Silicon provides the reader with a snapshot of neuromorphic engineering today. It is organized into five parts viewing state-of-the-art developments within neuromorphic engineering from different perspectives. Neuromorphic Systems Engineering: Neural Networks in Silicon provides the first collection of neuromorphic systems descriptions with firm foundations in silicon. Topics presented include: large scale analog systems in silicon neuromorphic silicon auditory (ear) and vision (eye) systems in silicon learning and adaptation in silicon merging biology and technology micropower analog circuit design analog memory analog interchipcommunication on digital buses £/LIST£ Neuromorphic Systems Engineering: Neural Networks in Silicon serves as an excellent resource for scientists, researchers and engineers in this emerging field, and may also be used as a text for advanced courses on the subject.

Download or read book Design of Modulators for Oversampled Converters written by Feng Wang and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 162 pages. Available in PDF, EPUB and Kindle. Book excerpt: Oversampled A/D converters have become very popular in recent years. Some of their advantages include relaxed requirements for anti-alias filters, relaxed requirements for component matching, high resolution and compatibility with digital VLSI technology. There is a significant amount of literature discussing the principle, theory and implementation of various oversampled converters. Such converters are likely to continue to proliferate in the foreseeable future. Additionally, more recently there has been great interest in low voltage and low power circuit design. New design techniques have been proposed for both the digital domain and the analog domain. Both trends point to the importance of the low-power design of oversampled A/D converters. Unfortunately, there has been no systematic study of the optimal design of modulators for oversampled converters. Design has generally focused on new architectures with little attention being paid to optimization. The goal of Design of Modulators for Oversampled Converters is to develop a methodology for the optimal design of modulators in oversampled converters. The primary focus of the presentation is on minimizing power consumption and understanding and limiting the nonlinearities that result in such converters. Design of Modulators for Oversampled Converters offers a quantitative justification for the various design tradeoffs and serves as a guide for designing low-power highly linear oversampled converters. Design of Modulators for Oversampled Converters will serve as a valuable guide for circuit design practitioners, university researchers and graduate students who are interested in this fast-moving area.

Download or read book Design of Low Voltage Low Power CMOS Delta Sigma A D Converters written by Vincenzo Peluso and published by Springer Science & Business Media. This book was released on 2013-03-09 with total page 178 pages. Available in PDF, EPUB and Kindle. Book excerpt: Design of Low-Voltage Low-Power CMOS Delta-Sigma A/D Converters investigates the feasibility of designing Delta-Sigma Analog to Digital Converters for very low supply voltage (lower than 1.5V) and low power operation in standard CMOS processes. The chosen technique of implementation is the Switched Opamp Technique which provides Switched Capacitor operation at low supply voltage without the need to apply voltage multipliers or low VtMOST devices. A method of implementing the classic single loop and cascaded Delta-Sigma modulator topologies with half delay integrators is presented. Those topologies are studied in order to find the parameters that maximise the performance in terms of peak SNR. Based on a linear model, the performance degradations of higher order single loop and cascaded modulators, compared to a hypothetical ideal modulator, are quantified. An overview of low voltage Switched Capacitor design techniques, such as the use of voltage multipliers, low VtMOST devices and the Switched Opamp Technique, is given. An in-depth discussion of the present status of the Switched Opamp Technique covers the single-ended Original Switched Opamp Technique, the Modified Switched Opamp Technique, which allows lower supply voltage operation, and differential implementation including common mode control techniques. The restrictions imposed on the analog circuits by low supply voltage operation are investigated. Several low voltage circuit building blocks, some of which are new, are discussed. A new low voltage class AB OTA, especially suited for differential Switched Opamp applications, together with a common mode feedback amplifier and a comparator are presented and analyzed. As part of a systematic top-down design approach, the non-ideal charge transfer of the Switched Opamp integrator cell is modeled, based upon several models of the main opamp non-ideal characteristics. Behavioral simulations carried out with these models yield the required opamp specifications that ensure that the intended performance is met in an implementation. A power consumption analysis is performed. The influence of all design parameters, especially the low power supply voltage, is highlighted. Design guidelines towards low power operation are distilled. Two implementations are presented together with measurement results. The first one is a single-ended implementation of a Delta-Sigma ADC operating with 1.5V supply voltage and consuming 100 &mgr;W for a 74 dB dynamic range in a 3.4 kHz bandwidth. The second implementation is differential and operates with 900 mV. It achieves 77 dB dynamic range in 16 kHz bandwidth and consumes 40 &mgr;W. Design of Low-Voltage Low-Power CMOS Delta-Sigma A/D Converters is essential reading for analog design engineers and researchers.