Download or read book Initiation Ablation Precursor Formation and Instability Analysis of Thin Foil Liner Z pinches written by Isaac Curtis Blesener and published by . This book was released on 2012 with total page 135 pages. Available in PDF, EPUB and Kindle. Book excerpt: This dissertation presents the results of mostly experimental work studying the early-time behavior of thin foil liners as compared to wire-array Z-pinches. It involves three studies, covering initiation, ablation and precursor formation, and instability analysis. Initiation was studied by observing the optical emission of various thickness (0.6-23.5 um Cu) liners using a streak camera. It was found that thinner liners initiated sooner, more quickly, and more uniformly than thicker liners. This correlated well with both an increase in instantaneous dJ/dt at the time of first emission as well as the inductive voltage at the time of first emission. The threshold for uniform initiation was dJ/dt>3.5x1016 Acm[-]2 s[-]1 . Uniform initiation is important for liners because nonuniformities could lead to enhanced instabilities and poor liner performance (compression, x-ray production, etc.). Ablation and precursor formation of wire-arrays (16x75 um Cu) and liners (6 um Cu) were studied using r-[theta] density maps and radial mass profiles created by an axial X pinch radiography diagnostic. These images show very strong differences in this stage of the Z-pinch. Wire-arrays develop complex, azimuthally varying ablation structures that lead to dense precursors. Liners, however, show significantly reduced and azimuthally uniform ablation leading to an order of magnitude less dense precursor on axis. This is likely due to the discrete versus continuous nature of wire-arrays versus liners. With wire-arrays, plasma that is created on the outside of the wires can reach the array axis by being swept through the gaps between the stationary wire cores. In contrast, liners have no "gaps" for plasma to flow through. Therefore, any plasma that is created on the outside of the liner is trapped there until the bulk of the liner moves with the implosion. Consequently, only the plasma that is created on the inside of the liner is able to contribute to precursor formation. This is an important result because reduced precursor formation is important for fuel compression and heating in MagLIF. Less precursor can also lead to enhanced x-ray production because there is less mass on axis to cushion the conversion of kinetic energy into x-rays during the implosion and stagnation phases. Finally, in the instability studies, it was observed in laser shadowgraph images that liners develop a much larger amplitude instability on their outside surface as compared to wire-arrays. This is an important discovery and could be detrimental to liner performance (compression, x-ray production, etc.) because it could lead to enhanced magnetic Rayleigh-Taylor (MRT) instability during the implosion phase. The reason for the larger instability in liners is again probably due to the fact that plasma builds up on the outside of the liners with no where to go. A possible source of the enhanced instability was found using 2D (xy) PERSEUS simulations comparing the results of MHD and Hall MHD simulations. The instability only developed in the Hall MHD case. The 2D nature of the simulation, along with all simulation parameters being equal between the two cases, rules out the possibility of MRT or m=0 for the cause of the instability (in the simulation). It was found that the Hall term was responsible for causing a shear-flow instability that developed later in time to resemble the experimental results.
Download or read book Physics of High Density Z Pinch Plasmas written by Michael A. Liberman and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 285 pages. Available in PDF, EPUB and Kindle. Book excerpt: A "z pinch" is a deceptively simple plasma configuration in which a longitudinal current produces a magnetic field that confines the plasma. Z-pinch research is currently one of the fastest growing areas of plasma physics, with revived interest in z-pinch controlled fusion reactors along with investigations of new z-pinch applications, such as very high power x-ray sources, high-energy neutrons sources, and ultra-high magnetic fields generators. This book provides a comprehensive review of the physics of dense z pinches and includes many recent experimental results.
Download or read book Assessment of Inertial Confinement Fusion Targets written by National Research Council and published by National Academies Press. This book was released on 2013-07-17 with total page 119 pages. Available in PDF, EPUB and Kindle. Book excerpt: In the fall of 2010, the Office of the U.S. Department of Energy's (DOE's) Secretary for Science asked for a National Research Council (NRC) committee to investigate the prospects for generating power using inertial confinement fusion (ICF) concepts, acknowledging that a key test of viability for this concept-ignition -could be demonstrated at the National Ignition Facility (NIF) at Lawrence Livermore National Laboratory (LLNL) in the relatively near term. The committee was asked to provide an unclassified report. However, DOE indicated that to fully assess this topic, the committee's deliberations would have to be informed by the results of some classified experiments and information, particularly in the area of ICF targets and nonproliferation. Thus, the Panel on the Assessment of Inertial Confinement Fusion Targets ("the panel") was assembled, composed of experts able to access the needed information. The panel was charged with advising the Committee on the Prospects for Inertial Confinement Fusion Energy Systems on these issues, both by internal discussion and by this unclassified report. A Panel on Fusion Target Physics ("the panel") will serve as a technical resource to the Committee on Inertial Confinement Energy Systems ("the Committee") and will prepare a report that describes the R&D challenges to providing suitable targets, on the basis of parameters established and provided to the Panel by the Committee. The Panel on Fusion Target Physics will prepare a report that will assess the current performance of fusion targets associated with various ICF concepts in order to understand: 1. The spectrum output; 2. The illumination geometry; 3. The high-gain geometry; and 4. The robustness of the target design. The panel addressed the potential impacts of the use and development of current concepts for Inertial Fusion Energy on the proliferation of nuclear weapons information and technology, as appropriate. The Panel examined technology options, but does not provide recommendations specific to any currently operating or proposed ICF facility.
Download or read book Impactful Times written by James R. Asay and published by Springer. This book was released on 2017-05-02 with total page 676 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book presents a history of shock compression science, including development of experimental, material modeling, and hydrodynamics code technologies over the past six decades at Sandia National Laboratories. The book is organized into a discussion of major accomplishments by decade with over 900 references, followed by a unique collection of 45 personal recollections detailing the trials, tribulations, and successes of building a world-class organization in the field. It explains some of the challenges researchers faced and the gratification they experienced when a discovery was made. Several visionary researchers made pioneering advances that integrated these three technologies into a cohesive capability to solve complex scientific and engineering problems. What approaches worked, which ones did not, and the applications of the research are described. Notable applications include the turret explosion aboard the USS Iowa and the Shoemaker-Levy comet impact on Jupiter. The personal anecdotes and recollections make for a fascinating account of building a world-renowned capability from meager beginnings. This book will be inspiring to the expert, the non expert, and the early-career scientist. Undergraduate and graduate students in science and engineering who are contemplating different fields of study should find it especially compelling.
Download or read book An Assessment of the Prospects for Inertial Fusion Energy written by National Research Council and published by National Academies Press. This book was released on 2013-07-05 with total page 247 pages. Available in PDF, EPUB and Kindle. Book excerpt: The potential for using fusion energy to produce commercial electric power was first explored in the 1950s. Harnessing fusion energy offers the prospect of a nearly carbon-free energy source with a virtually unlimited supply of fuel. Unlike nuclear fission plants, appropriately designed fusion power plants would not produce the large amounts of high-level nuclear waste that requires long-term disposal. Due to these prospects, many nations have initiated research and development (R&D) programs aimed at developing fusion as an energy source. Two R&D approaches are being explored: magnetic fusion energy (MFE) and inertial fusion energy (IFE). An Assessment of the Prospects for Inertial Fusion Energy describes and assesses the current status of IFE research in the United States; compares the various technical approaches to IFE; and identifies the scientific and engineering challenges associated with developing inertial confinement fusion (ICF) in particular as an energy source. It also provides guidance on an R&D roadmap at the conceptual level for a national program focusing on the design and construction of an inertial fusion energy demonstration plant.
Download or read book Textbook of Plastic and Reconstructive Surgery written by Deepak K. Kalaskar and published by UCL Press. This book was released on 2016-08-02 with total page 491 pages. Available in PDF, EPUB and Kindle. Book excerpt: Written by experts from London’s renowned Royal Free Hospital, Textbook of Plastic and Reconstructive Surgery offers a comprehensive overview of the vast topic of reconstructive plastic surgery and its various subspecialties for introductory plastic surgery and surgical science courses. The book comprises five sections covering the fundamental principles of plastic surgery, cancer, burns and trauma, paediatric plastic surgery and aesthetic surgery, and covers the breadth of knowledge that students need to further their career in this exciting field. Additional coverage of areas in which reconstructive surgery techniques are called upon includes abdominal wall reconstruction, ear reconstruction and genital reconstruction. A chapter on aesthetic surgery includes facial aesthetic surgery and blepharoplasty, aesthetic breast surgery, body contouring and the evolution of hair transplantation.The broad scope of this volume and attention to often neglected specialisms such as military plastic surgery make this a unique contribution to the field. Heavily illustrated throughout, Textbook of Plastic and Reconstructive Surgery is essential reading for anyone interested in furthering their knowledge of this exciting field. This book was produced as part of JISC's Institution as e-Textbook Publisher project. Find out more at https://www.jisc.ac.uk/rd/projects/institution-as-e-textbook-publisher
Download or read book Metal Nanoparticles in Microbiology written by Mahendra Rai and published by Springer Science & Business Media. This book was released on 2011-04-02 with total page 306 pages. Available in PDF, EPUB and Kindle. Book excerpt: Following an introduction to biogenic metal nanoparticles, this book presents how they can be biosynthesized using bacteria, fungi and yeast, as well as their potential applications in biomedicine. It is shown that the synthesis of nanoparticles using microbes is eco-friendly and results in reproducible metal nanoparticles of well-defined sizes, shapes and structures. This biotechnological approach based on the process of biomineralization exploits the effectiveness and flexibility of biological systems. Chapters include practical protocols for microbial synthesis of nanoparticles and microbial screening methods for isolating a specific nanoparticle producer as well as reviews on process optimization, industrial scale production, biomolecule-nanoparticle interactions, magnetosomes, silver nanoparticles and their numerous applications in medicine, and the application of gold nanoparticles in developing sensitive biosensors.
Download or read book Laboratory Astrophysics written by Guillermo M. Muñoz Caro and published by Springer. This book was released on 2018-10-11 with total page 237 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book focuses on the most recent, relevant, comprehensive and significant aspects in the well-established multidisciplinary field Laboratory Astrophysics. It focuses on astrophysical environments, which include asteroids, comets, the interstellar medium, and circumstellar and circumplanetary regions. Its scope lies between physics and chemistry, since it explores physical properties of the gas, ice, and dust present in those systems, as well as chemical reactions occurring in the gas phase, the bare dust surface, or in the ice bulk and its surface. Each chapter provides the necessary mathematical background to understand the subject, followed by a case study of the corresponding system. The book provides adequate material to help interpret the observations, or the computer models of astrophysical environments. It introduces and describes the use of spectroscopic tools for laboratory astrophysics. This book is mainly addressed to PhD graduates working in this field or observers and modelers searching for information on ice and dust processes.
Download or read book Nondestructive Characterization of Materials IV written by J.F. Bussière and published by Springer Science & Business Media. This book was released on 2013-11-11 with total page 506 pages. Available in PDF, EPUB and Kindle. Book excerpt: There is a great deal of interest in extending nondestructive technologies beyond the location and identification of cracks and voids. Specifically there is growing interest in the application of nondestructive evaluation (NOEl to the measurement of physical and mechanical properties of materials. The measurement of materials properties is often referred to as materials characterization; thus nondestructive techniques applied to characterization become nondestructive characterization (NDCl. There are a number of meetings, proceedings and journals focused upon nondestructive technologies and the detection and identification of cracks and voids. However, the series of symposia, of which these proceedings represent the fourth, are the only meetings uniquely focused upon nondestructive characterization. Moreover, these symposia are especially concerned with stimulating communication between the materials, mechanical and manufacturing engineer and the NDE technology oriented engineer and scientist. These symposia recognize that it is the welding of these areas of expertise that is necessary for practical development and application of NDC technology to measurements of components for in service life time and sensor technology for intelligent processing of materials. These proceedings are from the fourth international symposia and are edited by c.o. Ruud, J. F. Bussiere and R.E. Green, Jr. . The dates, places, etc of the symposia held to date area as follows: Symposia on Nondestructive Methods for TITLE: Material Property Determination DATES: April 6-8, 1983 PLACE: Hershey, PA, USA CHAIRPERSONS: C.O. Ruud and R.E. Green, Jr.
Download or read book The Physics Of Laser Plasma Interactions written by William Kruer and published by CRC Press. This book was released on 2019-08-20 with total page 176 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book focuses on the physics of laser plasma interactions and presents a complementary and very useful numerical model of plasmas. It describes the linear theory of light wave propagation in plasmas, including linear mode conversion into plasma waves and collisional damping.
Download or read book High Energy Density Physics written by R. Paul Drake and published by Springer Science & Business Media. This book was released on 2006-08-31 with total page 542 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book has two goals. One goal is to provide a means for those new to high-energy-density physics to gain a broad foundation from one text. The second goal is to provide a useful working reference for those in the ?eld. This book has at least four possible applications in an academic c- text. It can be used for training in high-energy-density physics, in support of the growing number of university and laboratory research groups working in this area. It also can be used by schools with an emphasis on ultrafast lasers, to provide some introduction to issues present in all laser–target - perimentswithhigh-powerlasers,andwiththoroughcoverageofthematerial in Chap. 11 on relativistic systems. In addition, it could be used by physics, applied physics, or engineering departments to provide in a single course an introduction to the basics of ?uid mechanics and radiative transfer, with d- matic applications. Finally, it could be used by astrophysics departments for a similar purpose, with the parallel bene?t of training the students in the similarities and di?erences between laboratory and astrophysical systems. The notation in this text is deliberately sparse and when possible a given symbol has only one meaning. A de?nition of the symbols used is given in Appendix A. In various cases, additional subscripts are added to distinguish among cases of the same quantity, as for example in the use of ? and ? 1 2 to distinguish the mass density in two di?erent regions.
Download or read book Webster s New World Medical Dictionary written by and published by . This book was released on 2008 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: Webster's New World Medical Dictionary, Third Edition will help you understand and communicate your medical needs when it matters the most. Written by doctors and the experts at WebMD, this edition includes 8500 entries, including 500 new terms, a vitamin appendix, and a companion website to give you access to medical language.
Download or read book Hot Embossing written by Matthias Worgull and published by William Andrew. This book was released on 2009-09-28 with total page 368 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book is an overview of replication technology for micro- and nanostructures, focusing on the techniques and technology of hot embossing, a scaleable and multi-purpose technology for the manufacture of devices such as BioMEMS and microfluidic devices which are expected to revolutionize a wide range of medical and industrial processes over the coming decade.The hot embossing process for replicating microstructures was developed by the Forschungszentrum Karlsruhe (Karlsruhe Institute of Technology) where the author is head of the Nanoreplication Group. Worgull fills a gap in existing information by fully detailing the technology and techniques of hot embossing. He also covers nanoimprinting, a process related to hot embossing, with examples of actual research topics and new applications in nanoreplication. - A practical and theoretical guide to selecting the materials, machinery and processes involved in microreplication using hot embossing techniques - Compares different replication processes such as: micro injection molding, micro thermoforming, micro hot embossing, and nanoimprinting - Details commercially available hot embossing machinery and components like tools and mold inserts
Download or read book Future Spacecraft Propulsion Systems written by Paul A. Czysz and published by Springer Science & Business Media. This book was released on 2006-09-19 with total page 488 pages. Available in PDF, EPUB and Kindle. Book excerpt: An understandable perspective on the types of space propulsion systems necessary to enable low-cost space flights to Earth orbit and to the Moon and the future developments necessary for exploration of the solar system and beyond to the stars.
Download or read book Handbook of Inductively Coupled Plasma Spectrometry written by Michael Thompson and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 452 pages. Available in PDF, EPUB and Kindle. Book excerpt: The first edition of our Handbook was written in 1983. In the preface to the first edition we noted the rapid development of inductively coupled plasma atomic emission spectrometry and its considerable potential for elemental analysis. The intervening five years have seen a substantial growth in ICP applications; much has happened and this is an appropriate time to present a revised edition. The basic approach of the book remains the same. This is a handbook, addressed to the user of the technique who seeks direct, practical advice. A concise summary of the technique is attempted. Detailed, theoretical treatment of the background to the method is not covered. We have, however, thoroughly revised much of the text, and new chapters have been added. These reflect the changes and progress in recent years. We are grateful to Mr Stephen Walton, Dr Gwendy Hall and London and Scandinavian Metallurgical Co. Ltd for their contributions. Chapter 3 (Instrumentation) has been rewritten by Mr Walton, the new Chapter on ICP-mass spectrometry has been written by Dr Hall, and London and Scandinavian provided much of the information for the chapter on metals analysis by ICP-AES. These chapters have been integrated into the book, and a conscious effort has been made to retain the unity of style within the book. New material has been added elsewhere in the book, archaeological materials are considered, pre concentration methods and chemometrics covered more fully.
Download or read book Plastics Materials and Processes written by Charles A. Harper and published by John Wiley & Sons. This book was released on 2003-10-10 with total page 1008 pages. Available in PDF, EPUB and Kindle. Book excerpt: Plastics Materials and Processes: A Concise Encyclopedia is a resource for anyone with an interest in plastic materials and processes, from seasoned professionals to laypeople. Arranged in alphabetical order, it clearly explains all of the materials and processes as well as their major application areas and usages. Plastics Materials and Processes: A Concise Encyclopedia: Discusses and describes applications and practical uses of the materials and processes. Clear definitions and sufficient depth to satisfy the information seekers needs
Download or read book J C Martin on Pulsed Power written by T. H. Martin and published by . This book was released on 2014-01-15 with total page 568 pages. Available in PDF, EPUB and Kindle. Book excerpt:
